Download 1994 Chevy Truck C 1500 Truck 2WD V6-262 4.3L VIN Z Vehicle Level Maintenance Tune-up and Engine Performance Checks Ignition Timing Technical Service Bulletins Ignition – Timing Connector Location Change. INFORMATION SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1).… Read More
Download 1996 Chevrolet Chevy K Pickup – 4WD | Chevy Pickup, GMC Pickup, Suburban, Tahoe, Yukon (VIN C/K) Service Manual DTC P1351 Ignition Coil Control Circuit High Voltage. Circuit Description The enhanced ignition system uses the crank sensor in order to provide the timing input to the VCM. The VCM uses this reference pulse in order to determine the individual ignition spark timing for each cylinder. Once the VCM calculates the ignition timing, the ignition coil module on the IC circuit receives the timing signal. Each timing pulse received by the ignition coil module on the IC circuit triggers the coil module in order to operate the ignition coil. The secondary ignition voltage is induced, and then the secondary ignition voltage is sent to the distributor for distribution to each spark plug. This DTC is a type A DTC. The IC signal voltage ranges from about 0.5 volt to 4.5 volts.… Read More
Download Malfunction Indicator Lamp (MIL) On, Transmission Stuck in Second or Third Gear, Instrument Cluster Inoperative (Verify and Repair Source of Voltage Loss In Transmission Solenoid Power Supply Circuit ) Models: 2006 and Prior GM Passenger Cars and Light Duty Trucks 2005-2006 HUMMER H2 2006 HUMMER H3 2005-2006 Saab 9-7X with 4L60-E, 4L65-E, 4L80-E or 4L85-E Automatic Transmission (RPOs M30, M32, M33, MT1, MN8) Condition Some customers may comment on one or more of the following conditions: Upon investigation, one or all of the diagnostic trouble codes (DTCs) P0740, P0753, P0758, P0785, P0787, P0973, P0976, P1860, P2761, P2764 and P2769 may be set depending on the vehicle. Cause The most likely cause of this condition may be a loss of voltage to the transmission solenoid power supply circuit. This condition may also be the result of an incorrect installation of an aftermarket electronic device such as a remote starter or alarm system.… Read More
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More
Download 2005 Chevy Truck Silverado 1500 2WD V8-5.3L VIN T Vehicle Level Heating and Air Conditioning Blower Motor Resistor Service and Repair Blower Motor Resistor Replacement. BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor. 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.… Read More
Download 1999-2000 Cadillac Escalade (Old Style) 2002-2004 Cadillac Escalade, Escalade EXT 2003-2004 Cadillac Escalade ESV 1996-1999 Chevrolet 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 Chevrolet 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 Chevrolet Silverado Extended Cab Short Box (New Style) 1999-2004 Chevrolet Silverado 1500 Series Regular Cab (New Style) 2000-2004 Chevrolet 1500 Series Avalanche, Suburban and Tahoe 2001-2004 Chevrolet Silverado 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 Chevrolet Silverado 2500 Series Crew Cab, Short Box (New Style) 1996-1999 GMC 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 GMC 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 GMC Sierra Extended Cab Short Box (New Style) 1999-2004 GMC Sierra 1500 Series Regular Cab (New Style) 2000-2004 GMC 1500 Series Yukon, Yukon XL 2001-2004 GMC Sierra 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 GMC Sierra 2500 Series Crew Cab, Short Box (New Style) 2003-2005 HUMMER H2 with Four Wheel Drive (4WD) or All Wheel Drive (AWD) and One-Piece Propeller Shaft ONLY.… Read More
Download CAUTION: MAKE SURE THE IGNITION SWITCH IS OFF!! The wire from the ignition switch to the ignition coil primary terminal is NOT fused in many applications. If this wire is allowed to touch vehicle or engine ground, with the ignition switch on, it can cause a direct short on the battery possibly causing permanent damage to the vehicle wiring and a fire. Cypress Engineering assumes no liability for damage caused from this occurrence or due to any faults in the existing vehicle wiring. 5. Remove the ignition switch wire from the ignition coil primary positive (+) terminal. Make sure this wire does not come into contact with vehicle or engine ground. 6. Remove the ignition coil and mounting strap from the fan housing and set them aside. 7. Remove the stock distributor and set it aside. 8. Install the Compu-Tronix DIS4-2.3 L Ford Electronic Distributor. Tighten the clamp just enough so that the distributor can still be turned by hand.… Read More
Download Removing – Remove driver’s-side airbag unit and steering wheel. Repair Manual, Body Interior, Repair Group 69 – Remove steering column switches Page 94-37 . – Insert spare or shop key and switch ignition on: access hole will appear in front of switch next to ignition key slot. Installing – Insert length of steel wire or small screwdriver (approx. 2 mm dia.) as far as it will go, as illustrated, and pull lock cylinder out of steering lock housing in direction of arrow. – Ignition switch must be in “ignition on” position. – Push lock cylinder with ignition key all way into steering lock housing and press in firmly until catch engages audibly. – Install steering column switches and steering wheel. Ignition switch, removing and installing Removing Note: It is not necessary to remove the lock cylinder. – Disconnect battery Ground (GND) strap. – Remove driver’s-side airbag unit and steering wheel.… Read More
Download Mode 1 Mode 2 ? Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 2002-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More
Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More