Download kit Torx T-35 screwdriver Soldering iron Solder Heat gun or other heat source to heat shrink tubing Drill with 3/8″ bit Small wire cutters Wire strippers that go down to 20 gage wire Electrical Tape Drop or Flash Light Hanger for pulling wire Step Description Completed (check) 1 Place Telematics box in Service Mode. 2 Remove Fuse SB13. 3 Remove driver’s side trim and Telematics box from under carpet. 4 Disconnect wiring from Telematics box. Drill hole for wiring harness. Modify six connections on the 42 pin connector. 5 Install cover on 42 pin connector, plug into Telematics box, install Fuse SB13. Plug all components into HCB- 30 brain box, turn on ignition and test. 6 Mount HCB-30 brain box, run wiring. 7 Replace Telematics box, replace carpet. 8 Mount and route the microphone and wire. 9 Mount and route the touch pad and wire. 10 Take Telematics box out of Service Mode.… Read More

Download Mode 1 Mode 2 ? Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 2002-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

Download
PRE-INSTALLATION CHECKS : (For the Installer) – Disconnect the negative terminal of the battery and only re- connect after the installation is complete. – Remove the cover from the rear of the unit, these allow access to the SW2- SW3. SW1 is located next to the connectors. Arrange the central unit as follows: a. SW1 in position A. Voltage drop sensor activated. SW1 in position B. Voltage drop sensor isolated. This sensor must be isolated if on the vehicle there are loads that can operate once the ignition has been switched off (i.e. cooling fan). b. SW2 in position A o B as shown in central locking diagrams. c. SW3 in position A. Continous signal. SW3 in position B. Intermittent signal. For connecting vehicle’s own horn select position B (intermittent signal). d. To de-activate the passive arming function, cut the YELLOW- GREEN wire loop. WIRING INSTRUCTIONS – Check that all wires of the harnesses are fitted in the correct positions on the connectors (checking against alarm wiring diagrams).… Read More

Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

Download Models Honda Accord: 1999-2002 Honda Odyssey: 1999-2002 Honda Prelude 1999 Acura CL 2001-2002 Acura Integra: 2001-2002 Acura MDX: 2001-2002 Acura TL: 2001-2002. Installation Instructions 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide . 3. Wire the 555H as shown in the wiring diagram. Wire Color Guide SYNCH BLUE, ORANGE/BLUE, or BLUE/WHITE DATA RED OR BLUE/GREEN KEY SENSE BLUE/WHITE. Wire Connection Guide BLUE/WHITE: Connect this wire to the (-) key sense wire at the ignition cylinder. The key sense wire rests at ground when the key is inserted into the ignition switch. BLACK: Connect this wire to a quality chassis ground (preferably scraped sheet metal) separate from other component ground locations. BLUE: Connect this wire to the BLUE status output of the remote start.… Read More

Download Civic EX/Si 92-00, Del Sol Si/VTEC 92-95, Integra GSR/Type R 94-01,Prelude 97-01 S2000. Installation 1. Locate the original ECU. On most cars it is in the passenger side “kick panel” near the passenger’s feet. On the Prelude models, it is on the floor directly below the passenger’s feet. On the S2000 the ECU is located in the left side kick panel. 2. Locate the plugs needed for the VPAC wiring connections by looking at the illustration for your model and year. 3. Mount the VPAC using the “hook and loop” fastener tape to a convenient location on the dash or in the glove box. Route the wires to the ECU location. 4. Follow the instructions for your vehicle to complete the wiring. 5. Reinstall the ECU, ECU cover/kick panel/carpeting in the reverse order of removal. 6. Go have fun with your new VPAC. Civic EX/Si 92-95 and Del Sol SI/VTEC 92-95 1.… Read More