2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More

2000 Chevy Truck S10/T10 Transfer Case Replacement

Download 2000 Chevy Truck S10/T10 Blazer 4WD V6-4.3L VIN W Vehicle Level Transmission and Drivetrain Transfer Case Service and Repair NVG 233/243-NP1 Transfer Case Replacement. Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 7. Remove any wiring harness from the transfer case. 8. Support the transfer case with a transmission jack. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case. 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case.… Read More

2005 Chevy Truck Silverado 1500 Blower Motor Resistor Replacement

Download 2005 Chevy Truck Silverado 1500 2WD V8-5.3L VIN T Vehicle Level Heating and Air Conditioning Blower Motor Resistor Service and Repair Blower Motor Resistor Replacement. BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor. 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.… Read More

1997 Chevy Truck C Tahoe Interior Lighting Module Locations

Download 1997 Chevy Truck C Tahoe 2WD V8-5.7L VIN R View: Under Center Of Instrument Panel Zoom Sized for Print Interior Lamp Control Module, Remote Control Door Lock Receiver Manufacturer supplied 2 different possible locations. Look for 5 wire connector with wire colors: gray, white, orange, pink & black. #PIT3819: Location of Interior Lamp Control Module – keywords control dim dome electrical entry ground illumination inoperative keyless lens light remort resistor RKE short – (Dec 23, 2005) Subject: Location of Interior Lamp Control Module. Models: 1995-2000 Chevrolet C/K Trucks, Suburban and Tahoe 1995-2000 GMC Yukon and C/K Trucks Classic Body Style Only The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this P1. Condition/Concern When diagnosing a dome lamp concern on one of the vehicles listed above, you may be unable to locate the Interior Lamp Control Module that is called out in the Service Manual.… Read More

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

2004 Chevrolet Chevy K Silverado Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

Download Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages.… Read More

2001 Ford Lincoln LS Intake Manifold Upper

Download 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01. 2. Drain the engine cooling system. For additional information, refer to Section 303-03 . 3. Remove the engine appearance cover. 4. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 5. Disconnect the throttle position (TP) sensor and the idle air control (IAC) solenoid electrical connectors. 6. Disconnect the accelerator and speed control cables. 7. Remove the cable bracket. 1. Remove the bolts. 2. Remove the bracket. 8. Disconnect the throttle body hoses. 1. Disconnect the coolant hoses. 2. Disconnect the positive crankcase ventilation (PCV) hose. 3. Disconnect the vapor purge hose. 9. Disconnect the vacuum hose. 10. Disconnect the EGR to exhaust manifold tube nut. 11. Remove the cowl vent screen. For additional information, refer to Section 501-02 . 12. Remove the brace. 13. Remove the vacuum hoses from the mounting bracket.… Read More

2002 Mercury Sable Upper Intake Manifold

Download 1. Remove the air cleaner outlet tube. 2. Remove the pin-type retainers and the accelerator cable splash shield. 3. Disconnect the throttle cable and the cruise control cable. 4. Disconnect the Throttle Position Sensor (TPS) and Idle Air Control (IAC) valve electrical connectors. 5. Disconnect the harness Tom the throttle body stud. 6. Disconnect the Exhaust Gas Recirculation (EGR) vacuum regulator and vacuum supply hoses. 7. Disconnect the Positive Crankcase Ventilation (PCV) and Evaporative Emissions (EVAP) vacuum hoses. 8. Remove the EGR valve. 1 Disconnect the vacuum hose. 2 Remove the nuts. 3 Remove the bolts. 4 Remove the EGR valve. 9. Remove the EGR Vacuum Regulator (EVR) valve. 1 Disconnect the vacuum hose. 2 Disconnect the electrical connector. 3 Remove the bolts. 4 Remove the valve. 10. Remove the eight bolts and the upper intake manifold. * Remove and discard the gaskets. * Clean all mating surfaces. Installation 1.… Read More

Audi MK5/EOS/B6/A3 TURBOPOD™ INSTALLATION

Download 1. Please review this document before attempting your installation. PARTS LIST: Mk5/EOS, Audi B6 or Audi A3 ColumnPod 90° brass female elbow with barb connector Black rubber boot Rubber tubing – 2 – 5″ lengths Indigo, Spectrum or VDO boost gauge 6′ black nylon tubing NoBuzz T-fitting 2 – hose clamps 2 auto-tap electrical connectors 2 – 3′ electrical wire (for VDO gauge) 4 nylon zip ties TriLED bulb (for VDO gauge only) 2 electrical flag connectors (for VDO gauge) SUGGESTED TOOLS: Metric wrenches or sockets Torx drivers (star-shaped) Small flat-bladed screwdriver Wire cutter or electrical crimping tool Utility or X-Acto type knife Double-sided foam tape – 3M acrylic automotive tape recommended Teflon tape. INSTALLATION INSTRUCTIONS Use appropriate safety precautions at all times. Make sure car in securely parked and on a level surface. Remove positive terminal of battery when working with electricity. Remove engine cover 1. Disconnect the air intake hose with Torx driver 2.… Read More

1997 Explorer/Mountaineer Intake Manifold Service and Repair

Download 1. Disconnect the battery ground cable. 2. Remove the air cleaner outlet tube; refer to Section 303-12 3. Disconnect the ignition coil electrical connector and the noise suppressor electrical connector. 4. Disconnect the idle air control (IAC) electrical connector. 5. Disconnect the EGR backpressure transducer electrical connector. 6. Disconnect the EVR solenoid electrical and vacuum connectors. 7. Disconnect the brake booster vacuum hose from the upper intake manifold. 8. Disconnect the vacuum connector from the upper intake manifold. 9. Disconnect the vacuum connector from the fuel pressure regulator and remove the vacuum harness from the engine. 10. Disconnect the throttle position (TP) sensor electrical connector. 11. Disconnect the hoses from the EGR backpressure transducer ports. 12. Disconnect the six spark plug wires from the spark plugs. 13. Disconnect the spark plug wires from the seven retaining clips. 14. Remove the four ignition coil bolts and the ignition coil from the upper intake manifold.… Read More