how to reset the anti theft ford explorer 2002

You search Auto repair manual PDF about how to reset the anti theft ford explorer 2002, search results will appear below. If search results do not exist, please search by others keyword.

2002 FORD EXPLORER TRANSMISSION NO 3RD GEAR OR SLIPPING 2-3 SHIFT

Filed Under (Ford) by admin on 23-01-2014

Download FORD: MERCURY: 2002 EXPLORER 2002 MOUNTAINEER This article supersedes TSB 03-25-4 to update the 1. Loosen the intermediate band locknut on the description for labor operation “B”. There have been band adjustment screw. no changes made to the TSB procedure. 2. Using the special service tool (307-S022), tighten the suspect band adjustment screw to ISSUE 10 lb-ft (14 N•m). Some 2002 Explorer/Mountaineer vehicles built prior to 3/4/2002 with 5R55W transmission, may exhibit a. If the band adjustment torque cannot be no 3rd gear or slipping 2-3 shift with diagnostic achieved, both bands will need to be trouble codes (DTCs) P0733 and P0745 present. replaced. Proceed to PROCEDURE “B”. This may be due to a broken intermediate band. b. If the proper torque is achieved, the band is ACTION OK and does not need to be replaced. If the conditions described are verified: Proceed to Step 3 of PROCEDURE “A”. •Follow Service Procedure “A” to confirm band is 3.… Read More

1998 – 2001 Ford Explorer 4WD Ford Ranger Explorer Sport Trac / Edge Mountaineer 4WD Torsion bar key front leveling kit

Filed Under (Ford) by admin on 15-02-2014

Download Part # 22907 1998 – 2001 Ford Explorer 4WD 1998 – 2007 Ford Ranger / Explorer Sport Trac Edge / Mountaineer 4WD Torsion bar key front leveling kit Part# Description Qty. 22907-01 Torsion bar keys 2 22907INST Instruction manual (customer copy) 1 22907INST Instruction manual (installer copy) 1 WARNINGDECAL Warning decal 1 MIRRORHANGER Rear view mirror hanger 1. Important customer information: Tuff Country EZ-Ride Suspension highly recommends that a qualified and/or certified mechanic performs this installation. If you desire to return your vehicle to stock, it is the customers responsibility to save all stock hardware. This vehicles reaction and handling characteristics may differ from standard cars and/or trucks. Modifications to improve and/or enhance off road performance may raise the intended center of gravity. Extreme caution must be utilized when encountering driving conditions which may cause vehicle imbalance or loss of control. DRIVE SAFELY! Avoid abrupt maneuvers, such as sudden sharp turns which could cause a roll over, resulting in serious injury or death.… Read More

FORD PATS (PASSIVE ANTI THEFT SYSTEM) INITIALIZATION WITH THE 2534 GLOBAL PROGRAMMER

Filed Under (Ford) by admin on 01-01-2014

Download There are five types of PATS implementations from Ford (A, B, C, D, E). Refer to Table 1 (page 11) to identify what type of PATS your vehicle is equipped with. PATS initialization is generally performed after programming. The A or D version of PATS does not store the key information in the PCM, therefore NO PATS KEY RELEARN IS REQUIRED after programming. The B or C versions of PATS store the key information within the PCM and MUST be transferred to the new PCM, or relearned on the vehicle after the new PCM is installed. The E version of PATS also stores the key information within the PCM, but CANNOT be transferred to the new PCM. This type MUST be relearned on the vehicle after the new PCM is installed. Note: If you are just updating the existing PCM calibration with an update calibration, you must select the MODULE REPROGRAMMING function (not Programmable Module Installation).… Read More

2000-2004 Ford Focus ZX3 SVT Suspension Kit INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 17-03-2013

DownloadPARTS IN KIT: ITEM # QTY DESCRIPTION SERVICE PART # REPLACEMENT SOURCE 1 2 Spring, rear 2M5Z-5B669-AA Ford Dealer 2 2 Shock, rear 2M5Z-18125-BA Ford Dealer 3 1 Anti-roll bar, rear 1S4Z-5A772-BA Ford Dealer 4 1 Strut, RF 2M5Z-18124-BA Ford Dealer 5 1 Strut, LF 2M5Z-18124-BB Ford Dealer 6 2 Bump stop 2M5Z-3020-AA Ford Dealer 7 2 Spring, front 2M5Z-5310-AA Ford Dealer 8 2 Nut, upper strut piston W700212-S3091 Ford Dealer. TORQUE SPECIFICATIONS: FASTENER TORQUE (ft./lbs.) (EXCEPT WHERE NOTED) Rear shock upper mount nut 13 Rear shock lower mount nut 85 Rear lower control arm to knuckle 85 Rear anti-roll bar to control arm bolts 11 Rear anti-roll bar bushing clamp bolts 35 Upper strut piston nut 35 Strut tower nuts 18 Knuckle to strut bolt 66 Front anti-roll bar link to strut bolt 94 Caliper to Knuckle 21 Wheel nuts 37. REAR SUSPENSION INSTALLATION INSTRUCTIONS: STEP 1: Raise vehicle off ground and support with jack stands.… Read More

1999 – 2002 Ford F-150 2WD and Ford Expedition Front Big Brake Update

Filed Under (Ford) by admin on 01-01-2014

Download Kit Contents Your StopTech Big Brake kit includes the following: 1 pair of ST-40 four-piston calipers, sized specifically for the vehicle 1 set of high-performance street pads (not suitable for track use) 1 pair of 355 X 32mm two-piece rotor assemblies 1 pair of aluminum caliper adapter brackets 2 pair of 7/16-20 self-locking Jet nuts 2 pair of 12mm washers 1 pair of hub assemblies 1 pair of stainless steel brake lines 1 pair of Adel clamps 1 pair of 10mm button-head bolts (for use with the Adel clamps) 1 pair of self-locking nuts (for use with the Adel clamps) 1 pair of banjo bolts 2 pair of copper crush washer s 1 pair of rubber end caps. Tools and Equipment Required Different models and years of vehicle use different-sized fasteners, and every effort has been taken to correctly identify the proper sized tool for each step of the installation.… Read More

FORD LIMITED SLIP DIFFERENTIAL INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 11-01-2014

Download -IMPORTANT LUBRICANT NOTE- The Auburn Gear limited-slip differential design has been extensively tested with high quality non-synthetic 80W90 hypoid oils treated with GM or Ford friction additives (3 oz. of additive will treat 1 quart of oil). To avoid differential clutch chatter (noise) and for optimum performance, use the oil and additive described above. Use of other additive and oil types may cause differential clutch chatter. Ford Part Number: C8A219B546A GM Part Number: 1052358 PINION SHAFT MODIFICATION Certain “C” clip axle applications with high gear ratios will require pinion shaft modification due to the thickness of the ring gear. The thick ring gear will prohibit the pinion shaft from being removed making “C” clip installation impossible. Use the following procedure to modify the pinion shaft. 1. Modification to be 90º to the pinion shaft lock screw hole as shown. It is recommended that this be accomplished through grinding. 2. Remove sharp edge from modified section by buffing.… Read More

1995-1997 FORD EXPLORER TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS

Filed Under (Ford) by admin on 12-02-2014

Download FORD: 1995-1997 EXPLORER 2. Connect the New Generation Star (NGS) Tester ISSUE to the Data Link Connector (DLC) underneath The diagnostic procedure for binding or shudder the steering wheel. Monitor for any Diagnostic from transfer case in slow, tight turns while in 4 Trouble Codes (DTCs) set by the transfer case Auto mode may be inaccurate for some vehicles. that could indicate incorrect speed sensor function. Codes could include, but are not ACTION limited to: Diagnose transfer case binding or shudder concerns using the following Diagnostic Procedure. •P1836 – Front propshaft sensor circuit failure •P1837 – Rear propshaft sensor circuit failure DIAGNOSTIC PROCEDURE •P1874 – Hall effect sensor power short circuit to battery 1997 EXPLORER •P1875 – Hall effect sensor power circuit 1. Test drive the vehicle in 4 Auto, 4 High and 4 failure Low. Evaluate the vehicle in each of these NOTE modes. The vehicle should bind in turns in both ADDITIONAL CODES COULD BE SET AS WELL.… Read More

2002 Ford Explorer/Mountaineer Workshop Manual

Filed Under (Ford) by admin on 01-01-2014

Download CAUTION: Since the engine is not free-wheeling, timing procedures must be followed exactly or piston and valve damage may occur. 1. Remove the engine front cover (6019). For additional information, refer to Engine Front Cover in this section. 2. NOTE: Procedure is for either RH or LH ignition coil (12029); LH ignition coil is shown. Disconnect the ignition coil electrical connector and remove the retaining bolt. 3. Tilt the coil away from the fuel injection supply manifold. 4. Remove the ignition coil. 5. NOTE: Remove any foreign material from the spark plug wells with compressed air before removing the spark plugs. Remove the spark plugs. 6. Position the lobe of the camshaft up. 7. Install the special tool between the valve spring coils to prevent valve stem seal damage. 8. NOTE: The roller followers are positional. Mark the followers for installation in their original locations. NOTE: The last three roller followers must be removed with special service tool 303-581.… Read More

COMP Cams® Ford Timing Set Installation Instructions

Filed Under (Ford) by admin on 09-12-2013

Download Ford Timing Set Installation Instructions Thank you for choosing COMP Cams® products! We know you have options in valve train component selection and we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and also take a moment to review the included limited warranty information. Engine Application High Energy Magnum Hi-Tech Ford V6, 144-200 3223 Ford V6, 171 (2600-2800cc) 3236 Ford V8, 255, 289, 302 & Boss 302, 1965-1988 2120 3120 Ford V8, 289-351W & Boss 302, pre 1972 3220 Ford V8, 302-351W, 1972 & up 3230 Ford V8, 352-428, 1964-1974 3208 2108 3108 Ford V8, 351C, 351M, 400M, 1970-1982 3221 2121 3121 Ford V8, 429-460, 1968-1971 3222 2122 3122 Ford V8, 429-460, 1972-1987 2130 3130 Ford V8, 429-460 w/nine keyway crank gear 2134* Ford V8, 351W, 351W H.O., 1969-¹84 2135 3135 Ford V8, 5.0L 302 H.O., 1980-March 21, 1984 2131 3131 Ford V8, 5.0L 302, 351W, March 22, 1984-1992 2138 3138 Notes: * #2120 or #3120 should not be installed on 351W engines as they are designed for 255, 289, 302 or Boss 302 engines.… Read More

1999 Ford EXPLORER TRANSMISSION SLIPPING SHIFT/DELAYED

Filed Under (Ford) by admin on 02-04-2014

Download FORD: 1999 EXPLORER, RANGER MERCURY: 1999 MOUNTAINEER 6. Inspect the fluid pan for major contamination. ISSUE Slipping transmission shifts and/or delayed or no •If contamination is minimal, clean the main transmission engagements may occur on some control, but do not replace. vehicles. The Electronic Pressure Control (EPC) •If major contamination is present, perform solenoid may cause stress on the attaching bracket. normal transmission overhaul as required, This stress causes the bracket to break and the including main control replacement. Pay EPC solenoid to back out of its bore causing line particular attention to the condition of the pressure to drop too low or fluctuate, allowing friction plates. Repair as required. friction clutches to slip. 7. After repairs are completed, verify concern has ACTION been fixed. Diagnose and inspect for damaged EPC attachment PART NUMBER PART NAME bracket, and replace the bracket and EPC solenoid with new bracket and revised EPC solenoid.… Read More

You might also likeclose