1999 Chrysler Truck Blend Door Actuator Replacement

Download 1999 Chrysler Truck Town & Country LWB FWD V6-3.8L VIN L Vehicle Level Heating and Air Conditioning Air Door Air Door Actuator / Motor Service and Repair Blend Door Actuator Replacement. REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes.… Read More

2005 HONDA CR-V DOOR VISORS INSTALLATION INSTRUCTIONS

Download
PARTS LIST Left front door visor Right front door visor Left rear door visor Right rear door visor Installing the Front Door Visor 1. Lower the front door glass completely. Remove the door glass run channel from the door sash in the area shown. Do not remove the glass run channel from the door mirror base or the rear end of the door. AII 27171 TOOLS REQUIRED Isopropyl alcohol Shop towel Masking tape INSTALLATION NOTE: •These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors. Be careful not to damage the paint finish or glass run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours.… Read More

2003 Chevy Truck TrailBlazer Cooling System-Electro-Viscous Fan Clutch Operation

Download 2003 Chevy Truck TrailBlazer 2WD L6-4.2L VIN S Cooling System – Electro-Viscous Fan Clutch Operation. Subject: Operating Characteristics of the Electro-Viscous (EV) Fan Clutch and Diagnostic Tips for Cooling Fan Noise, Delayed Transmission Shifts and/or Engine Revving Too High Models: 2004-2006 Buick Rainier 2002-2006 Chevrolet TrailBlazer, TrailBlazer EXT 2006 Chevrolet TrailBlazer SS 2002-2006 GMC Envoy, Envoy XL 2004-2005 GMC Envoy XUV 2002-2004 Oldsmobile Bravada 2005-2006 Saab 9-7X with 4.2L I-6, 5.3L V-8 or 6.0L V-8 Engine (VINs S, P, M, H – RPOs LL8, LM4, LH6, LS2) Date/VIN Breakpoints for Vehicles with New EV Fan Clutch. Vehicles built after and including the Date or VIN Breakpoints listed in the table shown are equipped with the new electro-viscous (EV) fan clutch . Vehicles of any model year listed in “Models Affected” with labor code J3390 (claimed after June 8, 2005) with P/N 15293048 in Claim History may also be equipped with this new EV fan clutch .… Read More

2001-2006 Toyota Sequoia BACK DOOR POWER WINDOW INOPERATIVE

Download 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9.… Read More

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

2001 Mazda Truck MPV DX FRONT DOOR DISASSEMBLY/ASSEMBLY

Download 1. Lower or raise the front door glass so that the distance from the top of the front door glass at the rear end to the upper part of the front molding is 185 mm {7.3 in} 2. Disconnect the negative battery cable. 3. Remove the front door trim.4. Disassemble in the order indicated below. 1. Inner handle 2. Front door trim bracket 3. Door screen 4. Front door glass 5. Front manual window regulator 6. Front power window regulator 7. Glass run channel 8. Front door lock 9. Outer handle 10. Door key cylinder 11. Door weatherstrip 12. Door lower weatherstrip 5. Assemble in the reverse order of disassembly. Front Door Glass Disassembly Note 1. Remove the front door glass installation bolts. 2. Slant the front door glass as shown, and remove the front door glass from the inside of the front door. Outer Handle Assembly Note 1. Connect the door key cylinder harness of outer handle as shown.… Read More

1997-2003 Honda CRV Signal Mirror Manual Installation Instructions

Download
Door Panel & Mirror Housing Removal 2002-2003 Honda CRV:1. Open door and lower window. 2. Remove plastic cover from corner of door. 3. Pop-out and remove plastic inserts. 4. Remove door handle plastic cover. 5. Unscrew the (2) screws revealed by the removal of the door handle cover. 6. Pry out door handle as shown. Disengage latch behind door handle and remove door handle. 7. Remove the (2) screws beneath armrest. 8. Lift up and pull door panel out slightly as shown. Disconnect any wiring connection behind door panel. Remove door panel from door. 9. Unscrew the (3) nuts holding the mirror housing to the door. Remove mirror housing from door.
Door Panel & Mirror Housing Removal 1997-2001 Honda CRV : 1. Open door and lower window. 2. Remove screw and plastic grommet on inside corner of door. 3. Remove plastic cover from corner of door. 4. Disconnect the mirror wire harness.… Read More

2000-UP FORD FOCUS 4 Door Sedan / Wagon, 3 Door Hatchback Audio Installation Instructions

Download Preliminary: disconnect the negative battery cable. Antenna: the factory antenna is located in the center front of vehicles roof. Radio removal and in-dash installation: note: the factory radio provision is a custom ford double din. When installing an aftermarket din stereo a dash kit is needed. We recommend the scosche fm1375 or fmc1370 installation kit. A set of din removal tools is also needed to remove the factory head unit. We recommend the scosche dt-1 ford din removal tools. 1. Insert ford din removal tools to release clips, pull out stereo, disconnect and remove. Front door speaker installation: note : the factory speaker provision is for a 6 x 8″ speaker. When installing an aftermarket 5 ¼ or 6 ½ speaker, a speaker adapter is required. We recommend the scosche sa68. 1. Extract (7) t-15 torx screws from the perimeter of door panel. 2. Remove screw cover from door opener cup, and extract (1) # 2 philips head screw from behind.… Read More

2002 Buick Truck Rendezvous Trim Panel Replacement

Download Tools Required J 38778 Door Trim Pad and Garnish Clip Remover Removal Procedure 1. Open the door. 2. Disconnect the power window switch assembly. 3. Remove the screws from the front door trim panel 4. Use the J 38778 to remove the trim panel. 1. Reposition the electrical harness connectors. 2. Remove the trim panel from the vehicle. Installation Procedure Important: Before installing the front door trim panel , discard the old trim panel retainers and replace with NEW trim panel retainers. 1. Install the new retainers to the front door trim panel . 2. Route the electrical connectors through the trim panel . 3. Align the trim panel to the door inner panel, guiding the door handle through the trim panel. 4. Install the upper edge of the trim panel to the top edge of the inner door panel, pressing down firmly until the trim panel is fully seated.… Read More

Ford Focus PRO-FIT Linear Fuel Doors Installation Instructions

Download Tools you will need: ? Ratchet set ? Flathead screwdriver ? Drill and drill bits (for electric locking fuel door only) ? Small file ? Degreaser ? Clear Rags Parts list (items not to scale):1) Fuel door with pull cable attached (pull cable is on electric locking fuel door only) 2) Wiring harnesses (long and short) with actuator (electric locking fuel door only) 3) L-bracket (x 4) 4) Washer (x 4) 5) Nylock nut (x 4) 6) Long hex bolt (x 4) 7) Short hex bolt (x 6) 8) Fuse taps (3 sizes – electric locking fuel door only) 9) Fuse (electric locking fuel door only) 10) Switch (electric locking fuel door only) 11) Sticky pads (electric locking fuel door only) 12) Tie wraps (electric locking fuel door only) 13) Gas cap 14) Wrenches 15) Black strip caulk (not pictured) PRO-FIT Linear Fuel Doors Ford Focus – Installation Instructions Prep WARNING: Do not perform this install near a flame source due to the risk of fire or explosion from gas fumes.… Read More