how to replace vent actuator on a 2010 f150

You search Auto repair manual PDF about how to replace vent actuator on a 2010 f150, search results will appear below. If search results do not exist, please search by others keyword.

Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit

Filed Under (Other Manuals) by admin on 15-01-2014

Download DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit) Models: 1999-2007 Chevrolet Silverado (Classic) Models 1999-2007 GMC Sierra (Classic) Models 2007-2009 Chevrolet Silverado Models (Excluding Hybrid) 2007-2009 GMC Sierra Models (Excluding Hybrid) This bulletin is being revised to provide an updated picture of the remote filter box and to add an important statement to not replace the EVAP canister. Please discard Corporate Bulletin Number 02-06-04-037E (Section 06 — Engine/Propulsion System). Condition Some customers whose vehicles are operated in dusty type environments, such as farming or mining off*road type applications, may comment about the illumination of the check engine light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set. Cause Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition. Correction (1999-2007 Classic/Old Style Models) After following the published SI diagnostics for P0446 and determining that the EVAP canister vent valve is the cause of the MIL light, replace the existing EVAP canister vent valve assembly with a new assembly.… Read More

2005-2007 NISSAN PATHFINDER MIL “ON” WITH DTC P0442/P0448/P0455/P0456/P1446

Filed Under (Nissan) by admin on 02-01-2014

Download IF YOU CONFIRM: A MIL “ON” with one or more of the following DTC(s) stored: • P0442 / P0448 / P0455 / P0456 / P1446 AND • EVAP Vent Control S/V is stuck open or will not seal when operated/closed. ACTIONS: 1. Replace the EVAP Vent Control S/V. 2. Install the Filter Kit (refer to the Service Procedure in this bulletin). 3. Clear any DTCs stored in the ECM. SERVICE PROCEDURE Replace Vent Control Valve 1. Replace the EVAP Vent Control S/V. • Refer to section EC in the Service Manual for replacement information. Install Filter Kit 1. Remove the spare tire. 2. Remove the EVAP canister mounting bolt (see Figure 1). • The canister will drop about 3 inches which will give you working room at the top. 3. Disconnect the vent hose (see Figure 1). 4. Reach above the EVAP canister and disconnect the vent hose at the vent control valve and remove the hose (see Figure 2).… Read More

2001 Ford Windstar COWL TOP VENT PANEL Installation Instructions

Filed Under (Ford) by admin on 22-02-2014

Download 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top vent panel. 2. To install, reverse removal procedure. Tighten bolts and nuts to specification. See TORQUE SPECIFICATIONS . INTAKE MANIFOLD Removal 1. Remove cowl top vent panel. See COWL TOP VENT PANEL . Release fuel pressure and disconnect fuel lines. See FUEL PRESSURE RELEASE & FUEL LINE CONNECTIONS . 2. Disconnect negative battery cable. Drain cooling system. Remove air cleaner assembly and heat tube. Disconnect control cables and linkage at throttle body. Disconnect accelerator cable bracket, and secure aside. 3. Disconnect necessary linkages at intake manifold. Disconnect wiring harness connectors, vacuum hoses, coolant hoses and PCV hoses as necessary. Remove heater tube with fuel lines attached. 4. Remove A/C compressor support bracket (if equipped). Remove throttle body and EGR valve assembly. Note location of upper intake manifold bolts and studs.… Read More

Model 2010 Ford F150 Heritage Style Short Bed 1997 – 2004 TONNEAU INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 02-01-2014

Download PRE-INSTALLATION NOTES TONNEAU INSTALLATION GUIDE INSTALLATION KIT CHECKLIST A B C D G H I E F A: Hydraulic Struts B: Stainless Steel Bolts 5/16″ x 1 1/4″ C: J-Hooks & Wall Mounting Screws D: Clamps E: Spiral Rings F: Stainless Steel Washers 5/16″ G: Stainless Steel Lock Washers 5/16″ H: Forward Mounting Brackets I: Rear Mounting Brackets Page 1 Model 2010 Ford F150 Heritage Style Short Bed 1997 – 2004 Page 1 FORM # IG2010 Modified May 2008 Be sure to use only cleaners, waxes, etc., which are labeled ‘Safe for Plastics’. Make sure that chemicals or substances, which are not labeled ‘safe for plastics’, do not come in contact with your Undercover. Failure to do so could cause discoloration and/or structural damage to your Undercover and will void your warranty. Paint rubbing of the truck is normally not a problem, but is always a possibility with any tonneau.… Read More

Evaporative Emission (EVAP) Vent Valve Replacement

Filed Under (Other Manuals) by admin on 01-01-2014

Download 1. Turn OFF the ignition. 2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 3. Disconnect the electrical connector. 4. Remove the EVAP vent valve bracket bolt. 5. Remove the EVAP vent valve from the bracket. 6. Disconnect the vent hose from the EVAP vent valve. 7. Remove the EVAP vent valve. Installation Procedure 1. Install the EVAP vent valve on bracket. 2. Connect the vent hose. Canister vent hose should be routed below the fuel tank fill and vent hoses. Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener.… Read More

2008-2010 F-Super Duty 6.4L DIESEL ENGINES REPEAT RADIATOR LEAK

Filed Under (Ford) by admin on 30-01-2014

Download FORD: 2008-2010 F-Super Duty This article supersedes TSB 10-4-5 to update the a. With EOT at 195 °F (91 °C) drive on the Dealer Coding base part numbers. highway unloaded at 55-70 MPH (89-113 Km/h) constant speed to observe EOT and ISSUE ECT temp. Some 2008-2010 F-Super Duty vehicles built on or b. Test results/next steps: before 9/14/2009 and equipped with a 6.4L diesel engine may exhibit repeat radiator leaks due to (1) If EOT is less than 8 °F (4.4 °C) malfunctioning (hyper-extended) high temperature higher than ECT, and the coolant temp thermostats. fluctuates roughly 5 °F (2.7 °C) – the thermostats are okay and do not need ACTION to be replaced. Replace just the Follow the Service Procedure steps to correct the radiator. Refer to WSM, Section 303-03 condition. (Engine Cooling). SERVICE PROCEDURE (2) If EOT exceeds ECT by greater than 8 °F (4.4 °C) or if the ECT readings 1.… Read More

2004-2010 Ford F150 SuperRail Mounting Kit #3361

Filed Under (Ford) by admin on 09-12-2013

Download
Installation Instructions SPECIFICATIONS ?? Fits 2004-2010 Ford F-150 w/ 6’5″ bed. FOR KING PIN BOXES WITH A FLANGE : Figure3. 1. Place the Trailer Plate {J2} over the King Pin, with the guide wedge towards the rear of the trailer (wedge facing down). Align the Trailer Plate {J2} square with the king pin box and clamp in place to prevent movement. 2. Mark the holes for drilling through the Trailer Plate {J2} onto the King Pin Box flange. 3. Remove the Trailer Plate {J2} or use it as a guide and drill ¼ ” holes through the flange. 4. Re-install the Adapter Plate (as in step 1). 5. Use the ¼” bolts provided, to secure the Trailer Plate {J2} onto the king pin box flange. A minimum of 10 bolts must be used to fasten the plate on. For use with heavy trailers, more bolts will be needed to secure this plate.… Read More

2005-2010 Ford Mustang MANUAL TRANSMISSION SEPARATOR PLATET

Filed Under (Ford) by admin on 16-10-2013

Download FORD: 2005-2010 Mustang. This article supersedes TSB 8-2-10 to update the production fix date, vehicle model years and part list. ISSUE Some 2005-2010 Mustang vehicles built before 4/5/2009 and equipped with a 4.6L engine and manual transmission, may exhibit an oil-canning or exhaust rattle/buzz around 2000 – 2500 RPM during the first few minutes of driving after a cold start. The sound goes away after the car warms up. The concern may be caused by the separator plate, between the rear face of the engine block and the transmission housing, vibrating and/or contacting the flywheel. ACTION Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE 1. Remove transmission per Workshop Manual (WSM), Section 308-03B. 2. Pry separator plate from the rear face of the block alignment dowels and slide it out from between block and flywheel. Replace with new service part. 3. Install transmission per WSM, Section 308-03B.… Read More

2010-11 FORD Focus I4-2.0L PZEV 69-3516 Installation Instructions

Filed Under (Ford) by admin on 16-12-2013

Download 1. Turn off the ignition and disconnect the negative battery cable. 2. Disconnect the mass air sensor electrical connec- tion. 2010-11 FORD Focus I4-2.0L PZEV Flat blade screw driver Ratchet Extension 10mm socket 13mm socket 10mm wrench 3mm Allen wrench T20 torx 3. Release the locking tab and then disconnect the crank case vent line from the rear of cam cover as shown. 4. Remove EVAP hose from the EVAP valve as shown. 5. Release the three retaining clips securing the air box lid and loosen the hose clamp at the throttle body. 6. Remove factory intake hose and air box lid from the vehicle. 7. Remove the two bolts securing the lower air box assembly to core support. 8. Pull up fi rmly to dislodge the air box from the grommet and remove the lower air box assembly from the vehicle as shown. 9. Remove air box grommet from inner fi nder well as shown.… Read More

2000-2007 Ford Taurus ERRATIC FLUID LEVEL READING ON TRANSAXLE DIPSTICK

Filed Under (Ford) by admin on 15-02-2014

Download Ford : 2000-2007 Taurus 2000-2003 Windstar 2004-2007 Freestar MERCURY: 2000-2005 Sable 2004-2007 Monterey. ISSUE: Some 2000-2007 Taurus, 2000-2005 Sable, 2000-2003 Windstar, and 2004-2007 Freestar/Monterey vehicles, equipped with a 4F50N, AX4N, or AX4S transaxle, may exhibit an erratic fluid level reading on the transaxle dipstick and possible leaks around the filler tube and grommet. The condition may be due to a restricted transaxle vent. ACTION: Repair the transaxle vent restriction by replacing the transaxle vent with a 90° vent stem, small hose clamp, two (2) tie raps, and 24″ (61 cm) of 5/16″ (8 mm) vacuum hose. The 5/16″ (8 mm) vacuum hose will be routed from the 90° vent on the transaxle back to the cowl area, next to the brake master cylinder and tie rapped in place with the end of the hose facing down. Refer to the following Service Procedures. SERVICE PROCEDURE 1. Disconnect the mass air flow (MAF) sensor electrical connector.… Read More

You might also likeclose