how to replace transmission cooler lines 03 trailblazer

You search Auto repair manual PDF about how to replace transmission cooler lines 03 trailblazer, search results will appear below. If search results do not exist, please search by others keyword.

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Filed Under (Other Manuals) by admin on 01-01-2014

Download Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) #05-07-30-031: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) – (Nov 11, 2005) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case.… Read More

Ford BD Performance Transmission Installation Instructions

Filed Under (Ford) by admin on 14-01-2014

Download
REMOVAL: 1) Disconnect the negative battery cable(s). 2) Place the transmission into the Neutral (N) position. 3) Raise the vehicle on a hoist. 4) Mark the drive shaft and pinion yokes for assembly alignment. On 4WD models, remove the skid plate. 5) Remove the transmission oil filter tube nut and filler tube. 6) Position a drain pan & disconnect the transmission fluid cooler tubes at the cooler bypass valve. 7) Remove the drive shaft. On 4WD models, remove the front drive shaft & transfer case assembly. On SuperDuty/Motorhome models, remove the transmission mounted parking brake assembly. 8) NOTE: If the vehicle is equipped with a PTO (Power Take-Off) unit, all or part of the PTO will need to be removed. 9) Disconnect the shift cable from the transmission and manual lever. 10) Disconnect the cable housing from the bracket. 11) Disconnect the digital transmission range (TR) sensor connector. 12) Remove the transmission heat shield.… Read More

1998 Chevrolet Blazer Engine Oil Cooler Hose/Pipe Replacement

Filed Under (Chevrolet (Chevy)) by admin on 12-03-2014

Download 1998 Chevrolet Blazer – 4WD | Blazer, Bravada, Jimmy, S10 Pickup,  Sonoma (VIN S/T) Service Manual | Engine | Engine Mechanical – 4.3L | Repair Instructions. Engine Oil Cooler Hose/Pipe Replacement (4WD) Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6.… Read More

2008 Ford Escape FLUID LEAK TRANSMISSION FLUID COOLER

Filed Under (Ford) by admin on 04-02-2014

Download FORD: MERCURY: 2008 Escape 2008 Mariner This article supersedes TSB 08-16-12 to change the OPERATION DESCRIPTION TIME production fix date. 090904A 2008 Escape/Mariner1.1 Hrs. CD4E Transmission: ISSUE Replace The Transmission Some 2008 Escape and Mariner vehicles (excluding Fluid Cooler, Includes Hybrids) built on or before 5/9/2008 and equipped Time To Remove And with a CD4E transmission may exhibit a fluid leak Install Bumper Cover, from the transmission cooler. Evacuate And Charge Air Conditioning System, Top ACTION Off Transmission Fluid (Do Follow the Service Procedure steps to correct the Not Use With 19700A, condition. 19700A7) DEALER CODING SERVICE PROCEDURE CONDITION BASIC PART NO. CODE Replace the transmission / A/C cooler with a new 19712 07 updated part following Workshop Manual (WSM), Section 412-01. PART NUMBER PART NAME 8L8Z-19712-J Transmission / A/C Cooler WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage IMPORTANT: Warranty coverage limits/policies are not altered by a TSB.… Read More

FORD TORQUE CONVERTER & TRANSMISSION Installation Instructions

Filed Under (Ford) by admin on 06-02-2014

Download REMOVAL Step 1 Before you begin – let vehicle cool for about an hour. Disconnect battery. Raise vehicle and support on jack stands. The higher you raise it, the easier it is to work under. If your installing a new transmission and converter, skip to STEP 3 Step 2 Drain oil from transmission by removing the drain plug. This is a good time to install a TCI® Drain Plug Kit, TCI® #805800. Pans without plug must be slowly removed by freeing one end and allowing bolts on other end to hold pan. The pan will drop down to allow the fluid to run out the end. Use a drain pan to catch fluid. Remove remainder of bolts and slowly lower pan and pour remainder of fluid in drain pan. Replace filter and clean pan and install new pan gasket. (New gaskets and filters available from TCI®). Reinstall pan and torque pan bolts to OEM specs.… Read More

MONSTER TRANSMISSIONS : FORD TRANSMISSION INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 31-12-2013

Download
Please Note : The following instructions were made to act as a guide/reference, if you are inexperienced with performing an automatic transmission installation it is highly recommended that you contact a certified experienced professional to perform the installation and/or make the proper adjustments for you! Instructions : (1) Pre-installation instructions; Disconnect Battery terminal, inspect and check transmission coolant lines for damage, flush lines and coolant system thoroughly. (2) Inspect crank well for converter hub wear, and clean this area. (3) Check Flywheel for cracks and converter bolt holes for wear. (4) Inspect back of engine block where transmission mates, ensure block is clean, no wires or cables are in the way of installation. (5) Inspect and verify both dowel pins are clean and secure in block. (6) Ensure Block Plate is aligned and straight. (7) Clean area of block so transmission can make a good ground. “Warning” Transmission will suffer permanent damage if grounded improperly!… Read More

FORD TRANSMISSION INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 15-03-2014

Download (1) Pre-installation instructions; Disconnect Battery terminal, inspect and check transmission coolant lines for damage, flush lines and coolant system thoroughly. (2) Inspect crank well for converter hub wear, and clean this area. (3) Check Flywheel for cracks and converter bolt holes for wear. (4) Inspect back of engine block where transmission mates, ensure block is clean, no wires or cables are in the way of installation. (5) Inspect and verify both dowel pins are clean and secure in block. (6) Ensure Block Plate is aligned and straight. (7) Clean area of block so transmission can make a good ground. “Warning” Transmission will suffer permanent damage if grounded improperly! Installation : (1) Transmission Fluid: you need about 10 to 12 quarts of fluid for installation, Dextron III with Mercon, 1968 – 1993 Vehicles and Mercon 5, 1994 and Newer, any brand name. (2) If transmission was purchased with a torque converter from Monster Transmission & Performance, no need to follow step (3).… Read More

2001 Chevrolet Chevy K Silverado Transmission Stuck in Second or Third Gear

Filed Under (Chevrolet (Chevy)) by admin on 19-12-2013

Download Malfunction Indicator Lamp (MIL) On, Transmission Stuck in Second or Third Gear, Instrument Cluster Inoperative (Verify and Repair Source of Voltage Loss In Transmission Solenoid Power Supply Circuit ) Models: 2006 and Prior GM Passenger Cars and Light Duty Trucks 2005-2006 HUMMER H2 2006 HUMMER H3 2005-2006 Saab 9-7X with 4L60-E, 4L65-E, 4L80-E or 4L85-E Automatic Transmission (RPOs M30, M32, M33, MT1, MN8) Condition Some customers may comment on one or more of the following conditions: Upon investigation, one or all of the diagnostic trouble codes (DTCs) P0740, P0753, P0758, P0785, P0787, P0973, P0976, P1860, P2761, P2764 and P2769 may be set depending on the vehicle. Cause The most likely cause of this condition may be a loss of voltage to the transmission solenoid power supply circuit. This condition may also be the result of an incorrect installation of an aftermarket electronic device such as a remote starter or alarm system.… Read More

2003 Chevy Truck TrailBlazer Service and Repair

Filed Under (Chevrolet (Chevy)) by admin on 16-02-2014

Download Transmission Oil Cooler Line Quick Connect Fitting Removal Procedure Important: The front and rear sections of the cooler lines can be serviced separately. Refer to the appropriate steps when servicing individual lines. Perform the following procedure when removing the cooler lines from the quick connect fittings. 1. Pull the plastic cap back from the quick connect fining and down along the cooler line about 5 cm (2 inch) . 2. Using a bent-tip screwdriver, pull on one of the open ends of the retaining ring in order to rotate the retaining ring around the quick connect fining until the retaining ring is out of position and can be completely removed. 3. Remove the retaining ring from the quick connect fitting. 4. Discard the retaining ring. 5. Pull the cooler line straight out from the quick connect fitting. Installation Procedure Important: * Do not reuse any of existing fittings if there is excessive corrosion.… Read More

Checking oil level in automatic transmission and adding oil

Filed Under (Other Manuals) by admin on 28-03-2014

Download TRANSMISSION 722.700 in MODEL 168.031 /032 /033 /131 /132 /133 TRANSMISSION 722.701 in MODEL 168.006 /007 /008 /009 /109 TRANSMISSION 722.702 in MODEL 168.035 /135 TRANSMISSION 722.750 /751 in MODEL 414.700. Adding transmission oil Risk of accident. Secure vehicle to prevent it from moving. AS00.00-Z-0005-01A Danger! Accidents may result if the vehicle starts off unintentionally with the Wear closed and snug-fitting work clothes. engine running. Risk of injury. Do not grasp hot or rotating parts. Crushing and burn injuries may result while working on engine during when it is being started or when it is in operation. 1 Remove locking pin (1) To do this, break off the plate on the locking pin using a suitable tool and press out the remaining pin in the cap downwards 2 Remove cap (2) 3 Fill with transmission oil The vehicle must be horizontal. Transmission oil (ATF) in accordance with BB00.40-P-0236-10A Specifications for Operating Fluids, sheet no.… Read More

You might also likeclose