". You can read and download the PDF file on this page, or you can watch the video tutorial. Please use another keyword if these document aren't what you look for.
Electrical problem 2004 Chevy Impala 6 cyl Front Wheel Drive Automatic 94000 miles How do I get the plastic cover off to replace the turn signal switch..
here is the procedure for removing the turn signal switch from the manual. hope this helps . Turn Signal Switch.
http://www.1aauto.com/ford-f150-truck-turn-signal-and-wiper-switch-lever/i/1azts00207 1A Auto shows you how to repair, install, fix, change or replace a.
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 09-12-2013
Download Removal Procedure 1. Disable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR. 2. Remove the upper and lower trim covers. Refer to Steering Column Trim Covers Replacement . 3. Remove the wire harness assembly (1) from the wire harness strap (2). 4. Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector. Fig. 29: Turn Signal & Multifunction Switch Assembly Connectors Courtesy of GENERAL MOTORS CORP. 5. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly out of the bulkhead connector (1). 6. Remove the 2 pan head tapping screws (1) and (3) from the turn signal and multifunction switch assembly (2). 7. Remove the turn signal and multifunction switch assembly (2) from the steering column tilt head assembly. Installation Procedure 1. Install the turn signal and multifunction switch assembly (2) onto the steering column tilt head assembly.… Read More
Download 2003 Chevrolet Impala LS MULTIFUNCTION, TURN SIGNAL SWITCH REPLACEMENT
Filed Under (Volkswagen (VW)) by Doe Namblas on 02-01-2014
Download Steering column, assembly WARNING:Special safety precautions and some different procedures apply to vehicles equipped with airbags CAUTION:Before working on the electrical system: Obtain radio anti-theft code. Ignition OFF ! Disconnect battery Ground (GND) strap. Note: After reconnecting battery: Activate vehicle equipment such as radio, clock and power windows as per service procedures and/or Owner’s Manual. On vehicles equipped with OBD II, activate readiness code. Refer to Powertrain Management, Computers and Control Systems, Testing and Inspection, Procedures See: Powertrain Management/Computers and Control Systems/Testing and Inspection For further information on the steering column assembly, refer to Steering and Suspension, Steering, Steering Column, Service and Repair. 1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig.… Read More
Download 2000 Volkswagen Cabrio Ignition Switch: Service and Repair
Filed Under (Other Manuals) by Doe Namblas on 26-12-2013
Download Models: 2004 Buick Rainier 2000-2004 Cadillac Escalade 2002-2004 Cadillac Escalade EXT 2003-2004 Cadillac Escalade ESV 1998-2004 Chevrolet Blazer, S-10 Pickup 1999-2004 Chevrolet Silverado 2000-2004 Chevrolet Suburban, Tahoe 2002-2004 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2004 Chevrolet Express 1998-2004 GMC Jimmy/Envoy, Sonoma 1999-2004 GMC Sierra 2000-2004 GMC Yukon, Yukon XL 2002-2004 GMC Envoy, Envoy XL 2003-2004 GMC Savana 2004 GMC Envoy XUV 1998-2004 Oldsmobile Bravada 2003-2004 HUMMER H2. #04-06-03-002: Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery – (Feb 5, 2004) When diagnosing a concern regarding an intermittent vehicle no crank or dead battery, technicians should remove and reinstall the ignition switch using the Ignition Switch Replacement procedure in the Steering Wheel and Column section of SI. The ignition switch may have been misindexed in the steering column during a previous replacement . If the ignition switch is misindexed in one direction, the ignition switch circuits will not be completely open when the ignition switch is in the OFF position with the key removed.… Read More
Download Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery
Filed Under (Other Manuals) by Doe Namblas on 02-04-2014
Download 1999-2000 Cadillac Escalade (Old Style) 2002-2004 Cadillac Escalade, Escalade EXT 2003-2004 Cadillac Escalade ESV 1996-1999 Chevrolet 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 Chevrolet 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 Chevrolet Silverado Extended Cab Short Box (New Style) 1999-2004 Chevrolet Silverado 1500 Series Regular Cab (New Style) 2000-2004 Chevrolet 1500 Series Avalanche, Suburban and Tahoe 2001-2004 Chevrolet Silverado 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 Chevrolet Silverado 2500 Series Crew Cab, Short Box (New Style) 1996-1999 GMC 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 GMC 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 GMC Sierra Extended Cab Short Box (New Style) 1999-2004 GMC Sierra 1500 Series Regular Cab (New Style) 2000-2004 GMC 1500 Series Yukon, Yukon XL 2001-2004 GMC Sierra 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 GMC Sierra 2500 Series Crew Cab, Short Box (New Style) 2003-2005 HUMMER H2 with Four Wheel Drive (4WD) or All Wheel Drive (AWD) and One-Piece Propeller Shaft ONLY.… Read More
Download Clunk, Bump or Squawk when Vehicle Comes to Complete Stop
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 02-12-2013
Download 1989 Chevrolet Corvette V8-350 5.7L Steering Column: Service and Repair Disassembly/Assembly SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE Disassembly 1. Remove steering wheel as follows: a. Disconnect battery ground cable, then remove horn cap from steering wheel by pulling. b. Disconnect horn button wire, then remove telescope lever screws and shaft lock knob screw. c. Remove telescope adjustment lever, steering wheel nut retainer and nut. d. Remove steering wheel with a puller. 2. Remove spacer, bumper, spacer and snap ring retainer (Nos. 2, 3, 4, and 5 in Fig. 59 ). 3. Remove shaft lock retainer using lock plate compressor to depress shaft lock. 4. Remove shaft lock and carrier assembly, upper bearing spring, upper bearing seat and inner race. 5. Reverse procedure to install. TURN SIGNAL SWITCH Disassembly 1. Remove SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE as previously outlined.… Read More
Download 1989 Chevrolet Corvette Steering Column: Service and Repair
Filed Under (Ford) by Doe Namblas on 31-12-2013
Download 1993 Ford Escort G – TESTS W/CODES – EEC-IV (1.9L)’ ’1993 ENGINE PERFORMANCE Ford Motor Co. – Self-Diagnostics – EEC-IV. CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH) Diagnostic Aids When ignition switch is in the ON or START position, the PCM connects FUEL PUMP circuit (PCM terminal No. 22) to ground. The fuel pump relay is energized and electrical current flows to the fuel pump. If PCM does not receive ignition PIP signal within 2 seconds, FUEL PUMP circuit is opened and fuel pump operation is terminated. Perform this test when instructed by QUICK TEST or CIRCUIT TEST AA. This test is only intended to diagnose: * Fuel pump relay. * Inertia Fuel Shutoff (IFS) switch. * Wiring harness circuits (B+, VPWR, FUEL PUMP, GND and POWER-TO-PUMP). * Faulty Powertrain Control Module (PCM). Fig. 31: Fuel Pump Monitor Circuit Diagram (Escort & Tracer) 1)Code 87/556: Check VPWR To Fuel Pump Relay Code 87/556 indicates a fuel pump primary circuit failure.… Read More
Download 1993 Ford Escort FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH)
Filed Under (Honda) by Doe Namblas on 24-01-2014
TURN SIGNAL RELOCATION 1. Refer to Figure 2. Remove seat.
SAFETY: DISCONNECT BATTERY PRIOR TO ALL WIRING MODIFICATIONS 2. Disconnect wires to turn signals and taillights under seat. 3. Remove three bolts on each side that secures fender to strut. 4. Lower fender onto tire and remove. 5. Remove turn signals from fender strut. Observe and mark “left” and “right” for re-installation. 6. Cut each turn signal wire 3″ from connector end and splice 24″ of electrical wire. Turn signal bracket must be oriented forward (ears of bracket to the front). 7. Remove license plate light mounting bolts. Remove grommet. Route turn signal wires through empty grommet hole, Refer to inset in figure 2, route wire past the taillight and through the existing hole in the fender. Using the wire clamp on the right side taillight bolt. Secure wire to taillight wire with the supplied tie wraps. 8. Install turn signal bracket between license plate and license plate bracket using 1/4-20 x 1 1/4″ Hex Cap Screw, 1/4″ flat washer, 1/4″ x 1″ flat washer, and 1/4″ nut.… Read More
Download Honda Aero Shadow 750 MODEL 334/S334 Manual Installation Instructions
Filed Under (Audi) by Doe Namblas on 31-12-2013
Download Audi TT Coupe 2000-2004, Audi TT Roadster 2001-2004 – Brake System. ABS/ESP ITT Mark 20 system components, removing and installing Brake light switch (square housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once. Removing – Remove storage compartment on driver’s side. Repair Manual, Body Interior, Repair Group 68; Storage compartments, covers – Unplug electrical connector. – Remove brake light switch -1- by turning counter-clockwise through 90. Installing Install in reverse sequence; note the following points: – Pull brake light switch plunger fully out. – Press brake pedal down as far as possible by hand. – Guide switch through installation hole and secure by turning 90 clockwise -arrows-. – Release brake pedal. – Make sure proper function of brake lights when brake pedal is pressed and released. Brake light switch (round housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once.… Read More
Download 2000-2004 Audi TT Coupe Brake System
Filed Under (Honda) by Doe Namblas on 01-01-2014
Download 2000-2004 Honda Insight IMA System Indicator On With IMA DTC 77 (P1447) or DTC 78 (P1449) PROBLEM The IMA system indicator comes on and IMA DTC 77 (P1447) (battery module deterioration) or DTC 78 (P1449) (battery module deterioration) is set. CORRECTIVE ACTION Replace the battery module. If needed, replace the motor control module (MCM), the battery condition monitor (BCM), or both. INSPECTION PROCEDURE 1. Turn the ignition switch to LOCK (0). 2. Remove the cargo floor mat (see page 20-44 of the 2000-04 Insight Service Manual). (In ISIS, use the keyword FLOOR MAT , and select Interior Trim Removal/Installation – Cargo Area from the list.) 3. Remove the battery module switch cover (two bolts), then remove the locking cover from the switch. 4. Flip the battery module switch to OFF . Reinstall the locking cover. 5. Wait at least 5 minutes to let the capacitors in the system discharge. 6.… Read More
Download 2000-2004 Honda Insight IMA System Indicator On
Filed Under (Honda) by Doe Namblas on 27-03-2014
Download MIL Comes On With DTC P2195 or P2197 (Supersedes 04-038, dated August 10, 2004, to update the information marked with the black bars) SYMPTOM The MIL is on, and DTC P2195 (rear air fuel ratio sensor signal stuck lean) or P2197 (front air fuel ratio sensor signal stuck lean) is set. PROBABLE CAUSE The ECM/PCM software incorrectly interprets sensor inputs, causing the codes to set. REPAIR PROCEDURE NOTE: •Before you update an ECM/PCM, make sure the battery in the vehicle is fully charged. •To prevent ECM/PCM damage, do not operate anything electrical (audio system, brakes, A/C, power windows, moonroof, etc.) during the update. 1. If not already done, load the May 2004 or later i N CD onto the i N master terminal. Loading instructions are included with the CD. 2. Update the ECM/PCM software with the HIM. For updating instructions, refer to Programming the HIM and Updating an ECM/PCM With a Programmed HIM in Service Bulletin 01-023, Updating Control Units/Modules .… Read More
Download 2003-2004 Honda Accord V6 REPAIR PROCEDURE