2002 Chrysler Voyager LX ACCESSORIES and EQUIPMENT Power Windows

Download TROUBLE SHOOTING Inspect power window circuit breaker (25-amp), located in left kick panel. Inspect fuse No. 28 (40-amp) in Intelligent Power Module (IPM). IPM is located on left side of engine compartment. Inspect ground at right “B” pillar. SYSTEM TESTS ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay.… Read More

2001-2006 Toyota Sequoia BACK DOOR POWER WINDOW INOPERATIVE

Download 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9.… Read More

2007 Toyota Camry Rear Bumper Removal and Replacement

Download REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.… Read More

1996-2000 Honda Civic 2-door Front Windows Bind

Download 1. Remove the door panel. Refer to section 20 of the 1996-00 Civic Service Manual. 2. Remove the armrest bracket, then pull down the plastic cover to gain access to the window regulator. 3. Carefully move the glass until you can see the glass mounting bolts, then loosen them. Slide the guide rearward, remove the glass from the guide, and carefully pull the glass out through the window slot. 4. Check the year and VIN. If the vehicle is a 1996 or 1997 within the affected VIN range, replace the window regulator. Go to step 5. If the vehicle is not a 1996 or 1997 within the affected VIN range, go to step 8. 5. Remove the two roller guide bolts and the two rear regulator mounting bolts; then remove the front regulator mounting bolts. 6. Disconnect the power window motor connector, and detach the harness clip (if applicable); then lift and remove the regulator through the opening in the door.… Read More

2003 Volvo S40 Replacing The Rear Brake Pads

Download 2003 Volvo S40 L4-1.9L Turbo VIN 27 B4204T4 Vehicle Level Brakes and Traction Control Disc Brake System Brake Pad Service and Repair Rear Brake Pads. Replacing The Rear Brake Pads Special Tools: 999 5782, 951 2834 General CAUTION: Replace the brake pads when the minimum thickness is 2 mm . Removing the rear brake pads Remove * the hub cap and the wheel * the retaining clip and the brake hose from the support * the upper bolt from the locating pin for the brake caliper . Twist the brake caliper backwards. Remove the brake pads. NOTE: Do not depress the brake pedal while the brake pads are removed. Checking and cleaning the rear brake calipers. Clean brake pad contact surfaces in the brake caliper and on the caliper mounting. Check the dirt guard for the piston. Replace the dirt guard if it is worn. Recondition the brake caliper if the dirt guard is defective.… Read More

AUDI NEW BEETLE ECU INSTALLATION

Download 1 Remove the Dash Panel. Place both hands on either side of the center dash panel, firmly grip and slide forward, then lift. Step 2 Remove Upper Dash Panel Screws. Remove the four T-20 torx screws securing the upper dash panel. Step 2 Remove the Upper Dash Panel. To remove the upper dash panel, firmly pull the panel upwards being careful not to damage it. Step 3 Remove Lower Dash Panel. Underneath you will find the ecu housing cover. Remove the torx T-20 screws that secure the cover. Pull the ECU housing cover upward to expose the ECU. Step 4 Remove the ECU. To remove the ECU wiring harness, pull the tabs on harness away from the ECU. As this is done, the harness connector will pull away from the ECU. The reinstallation of the ECU is the reverse of the removal. Step 5 Installing the Fuel Pressure Regulator. Depending on the ECU version of your Beetle, an upgraded FPR may be required.… Read More

2006-2007 Honda Civic Uneven or Rapid Rear Tire Wear

Download 2006-07 Civic 2-Door – ALL Except Si and Honda Accessory HFP Package. 2006-07 Civic 4-Door – ALL Except Si. Uneven or Rapid Rear Tire Wear NOTE: To ensure a proper repair and proper reimbursement, you must read this entire service bulletin before doing any work. SYMPTOM The customer may complain of uneven or rapid rear tire wear, a roaring noise from the rear, and/or a vibration at highway speeds. PROBABLE CAUSE The combination of the tires and the rear suspension geometry may cause rapid and uneven rear tire wear. Tires in an advanced stage of this diagonal or inner edge wear may cause vibration and/or a bad bearing type noise. (For more details, see TIRE INSPECTION AND QUALIFICATION on page 2). CORRECTIVE ACTION Install a rear upper control arm kit, replace the flange bolts, replace the worn tires (see the Tire Replacement Information chart on this page), and do a four-wheel alignment.… Read More

2007-2008 Toyota Tundra Rear Driveshaft/Propeller Shaft Clunk/Thunk Noise

Download 1. Confirm that the condition is the rear driveshaft clunk/thunk noise. A. Test drive the vehicle and confirm the customer’scomplaint. B. Place the transfer casein 4WDHighwiththe center differential lock ed. Remove the rear driveshaft and test drive the vehicle. Refer to the Technical Information System (TIS), 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Removal” C. Is the clunk/thunk noise eliminated when coming to a stop and/or when accelerating froma stop? •If Yes-Replace rear driveshaft (propeller shaft assembly). Go to Step 2. •If No-This TSB does NOT apply. Continue diagnosis to isolate cause of condition. 2. Install the NEW driveshaft (propeller shaft) assembly. Refer to TSB DL 001-07 for the installation method for 3 joint driveshaftassemb lies on 2007 model year Tundra. Refer to TIS, 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Installation” NOTE Re-usethespacers provided under the center support bearing to ensure the proper alignment of the center support bearing.… Read More

1988-2000 Honda Civic Clunk or Squeak From Rear Suspension

Download 1988-2000 Honda Civic – ALL 1997-2001 Honda CR-V – ALL 1993-2097 Honda Del Sol – ALL Clunk or Squeak From Rear Suspension SYMPTOM A clunk or squeak from the rear suspension when going over rough or bumpy roads. PROBABLE CAUSE Broken rear trailing arm bushing(s). CORRECTIVE ACTION Replace the rear trailing arm bushing(s). REPAIR PROCEDURE NOTE: ISIS online service manual information is only available for vehicles 1990 and newer. 1. Remove the rear trailing arm: •Refer to the suspension section of the appropriate service manual, or •Online, enter keyword REAR SUSPENSION, then select Suspension Arms Replacement from the list. 2. Mark the trailing arm at the arrow on the bottom of the bushing. 3. Place the arm on a hydraulic press, supported by the hub base, with the spindle facing up. 4. With the hub driver, press the old bushing out of the trailing arm. 5. Install the new bushing with the short end toward the outside of the vehicle.… Read More

2001 Mercury Cougar Rear Brakes – Moaning/Groaning Noise

Download MERCURY: 1999-2001 COUGAR ISSUE Some vehicles equipped with rear disc brakes may exhibit a “moaning/groaning” noise on initial brake application (cold soak). This may be caused by the rear brake pads vibrating in the caliper. Braking performance is not affected by this condition. ACTION Install revised Rear Disc Brake Service kit. Refer to the following Service Procedure for details. SERVICE PROCEDURE ^BRAKES – REAR BRAKE NOISE- “MOANING/GROANING” FROM REAR BRAKES WHEN COLD ^NOISE – “MOANING/GROANING” FROM REAR BRAKES WHEN COLD 1. Lift and support vehicle. Refer to the appropriate Workshop Manual, Section 100-01. 2. Remove both rear tire assemblies. 3. Remove rear brake pads per instructions in the Workshop Manual, Section 206- 04. 4. Remove U-spring from the top of the caliper and replace with L-spring supplied in kit (Figure 1). 5. Remove adhesive backing protection from new pads with C-springs (Figure 2) and install new pads into caliper. Use Pads XS7Z-2200-M for vehicles without 6.… Read More