how to replace rear main seal 1998 acura tl

You search Auto repair manual PDF about how to replace rear main seal 1998 acura tl, search results will appear below. If search results do not exist, please search by others keyword.

2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module

Filed Under (Acura) by admin on 24-11-2013

Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

FORD, CHRYSLER, PONTIAC, OLDS WINDAGE TRAY INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 31-12-2013

Download To install studs : Remove a main bolt (main cap can be removed or left in place), tap threads, coat coarse threads with oil, screw stud in by hand, thread 2 main nuts on tray stud and lock them tightly together, lightly tighten tray stud 10-15 ft/lbs (making very sure that double nuts are not slipping or have run into the main cap), remove the 2 main nuts, coat the fine threads with oil, install the stud washer and nut, torque main stud with oil to torque spec of 65 ft/lbs for 7/16″ or 85 ft/lbs for 1/2″ studs, install 1 silver tray adjusting nut on the 3/8″ fine thread with the serrated face towards you (away from the engine). Do all the required studs locations to mount the tray in this fashion. You are now ready to mount the tray assembly. To install tray : Once all necessary tray studs have been installed properly, consult the special considerations section for the initial tray height and correct width, adjust the tray nut to this height, slide tray assembly into place and onto mounting studs, make sure that tray is supported equally by all studs (no wobble), the install the 2nd silver tray nut with the serrations toward the tray and torque with oil to 35 ft/lbs.… Read More

1996-2000 Honda Civic Rear Main Oil Seal Leaks

Filed Under (Honda) by admin on 09-12-2013

Download 1996-00 Civic – ALL 2001 Civic – See VEHICLES AFFECTED Civic Rear Main Oil Seal Leaks (Supersedes 01-040, 1996 – 2001 Civic Rear Main Seal Leak , dated June 12, 2001) SYMPTOM The engine leaks oil between the block and the transmission. PROBABLE CAUSE The rear main oil seal (crankshaft oil seal) is contaminated. REPAIR PROCEDURE 1. Remove the transmission. Refer to section 13 or 14 of the appropriate service manual. 2. Remove and discard the rear main oil seal (crankshaft oil seal). 3. Install the new oil seal. Refer to page 7 – 29 of the ’96-00 service manual or page 7-27 of the ’01 service manual. 4. Reinstall the transmission. 5. Reinstall the drain plug with a new sealing washer. 6. Refill the transmission with the appropriate fluid. 7. 2001 models only. Do the idle learn procedure: Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off, then start the engine.… Read More

556H Honda / Acura Immobilizer Bypass Module Installation Instruction

Filed Under (Honda) by admin on 29-01-2014

Download Mode 1 Mode 2 ? Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 2002-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

1994 Audi S4 Rear Differential – Right and Left Side Seal

Filed Under (Audi) by admin on 06-04-2014

Download The following describes the procedure I used to remove and replace the right and left side rear differential seals on my 1994 Audi S4. This procedure should apply to the 1992 – 1994 S4 and the 1995-1997 S6 (the left seal process may be different on the ’96-’97 cars) and should be used in conjunction with the Bentley Repair Manual. Right Side Seal 1. Jack up the right rear of the car and support solidly on jackstands. The higher you jack the car, the better the access and the less likely oil will be lost when you remove the seal. 2. Remove the plastic gravel tray (four 13 mm bolts/nuts). 3. It is not necessary to drain the differential oil. When the axle flange and seal are removed, a small amount of oil may drain out. This can be caught in a drain pan. If you do decide to drain the differential oil, remove the fill plug BEFORE removing the drain plugs.… Read More

Torque Converter Oil Seal Installation Tool

Filed Under (Other Manuals) by admin on 31-03-2014

Download Applies To: All ModelsWith L4 or V6 Engine and A/TWith 44 mm I.D. Torque Converter Oil Seal Torque Converter Oil Seal Installation Tool The service manual procedure for installing the torque converter oil seal requires you to disassemble the transmission. Anew required special tool, which attaches to your existing 40 mm I.D. driver, lets you install this seal without removing the main shaft or disassembling the transmission. REQUIRED SPECIAL TOOLS Seal DriverAttachment: T/N 07XAD-001000A (Shippedtoall dealers March 2000 as a required special tool) 40 mmI.D. Driver: T/N 07746-0030100 ORDERING INFORMATION Additional seal driver attachments are available from American Honda using normal parts ordering procedures. WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. PROCEDURE 1. Remove the transmission (see section 14 of the appropriate service manual). 2. Remove and discard the torque converter oil seal. Be careful not to damage the torque converter housing. 3. Select the appropriate replacement seal.… Read More

1998 Acura 3.5RL ENGINE PERFORMANCE Basic Diagnostic Procedures

Filed Under (Honda) by admin on 01-01-2014

Download 1. Remove fuel tank filler cap. Listen for fuel pump operation noise at fuel tank filler. Fuel pump should operate for 2 seconds after ignition switch is turned on. If fuel pump operates as specified, fuel pump is okay. If fuel pump does not operate as specified, go to next step. 2. Turn ignition switch off. Remove rear seat or trunk floor to gain access to fuel pump connector. Disconnect fuel pump connector. Disconnect PGM-FI main relay connector. Connect a fused jumper wire between PGM-FI main relay connector FUEL PUMP fuse side terminal and fuel pump side terminal. See L – WIRING DIAGRAMS article. 3. Turn ignition switch on. Using a voltmeter connected to ground, check for battery voltage at fuel pump harness side connector. See L – WIRING DIAGRAMS article. If battery voltage is not present, check harness between fuel pump and FUEL PUMP fuse. Repair as necessary. If battery voltage is present, check fuel pump ground.… Read More

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Filed Under (Other Manuals) by admin on 01-01-2014

Download Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) #05-07-30-031: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) – (Nov 11, 2005) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case.… Read More

2000 Ford F-150 Rear Drive Axle/Differential

Filed Under (Ford) by admin on 01-01-2014

Download 1. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the RH kick panel area. Failure to do so can result in unexpected inflation or deflation of the air springs, which can result in shifting of the vehicle during these operations. Raise and support the vehicle. 2. Remove the wheel and tire assembly. 3. Remove the differential housing cover (4033). ? Drain the lubricant. For additional information, refer to Differential Housing Cover in this section. 4. Remove the brake calipers and discs. 5. Remove the differential pinion shaft (4211). 1. Remove and discard the differential pinion shaft lock bolt. 2. Remove the differential pinion shaft. 6. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers (4N237). 1.… Read More

2007 Toyota Camry Rear Bumper Removal and Replacement

Filed Under (Toyota) by admin on 06-04-2014

Download REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.… Read More

You might also likeclose