how to replace peugeot 407 cv joint

You search Auto repair manual PDF about how to replace peugeot 407 cv joint, search results will appear below. If search results do not exist, please search by others keyword.

1991 Infiniti G20 AXLE SHAFTS FRONT

Filed Under (Infiniti) by admin on 21-02-2014

Download 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts. REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose.… Read More

2008 Peugeot 308 Parrot RKi8400 Installation Guide

Filed Under (Peugeot) by admin on 31-12-2013

Download
Compatibility Car models Peugeot 207: > 2006 Peugeot 308: > 2007 Peugeot 307: > 2006 Peugeot 407: > 2006.
Installation of the Parrot RKi We recommend you to install the Parrot RKi before installing the UNIKA. Make sure the installation is correctly performed by checking if the «Good bye» message is displayed when you turn off the ignition. ? Refer to the documentation of your Parrot RKi for more information. Selecting the protocol Use the DIP switches located on one side of the UNIKA to select the protocol (resistive or CAN Bus / KBus) on which the vehicle is based. Warning: Make sure the UNIKA is not powered before selecting the protocol. Installing the UNIKA with the Parrot RKi8400. Replace the MKi part on the UNIKA cable by the provided RKi part. Connect the UNIKA between the Parrot RKi8400 and the vehicle wiring. If your vehicle is based on a CAN Bus or KBus protocol, the mode (A, B, C or D) is automatically defined.… Read More

2005 Peugeot 307 Digital Music Changer Installation Guide

Filed Under (Peugeot) by admin on 10-03-2014

Download Compatible with: CITROEN C2/C3/C4/C5/C6 & C8 with Blaupunkt/VDO RD4 head unit PEUGEOT with Blaupunkt/VDO RD4 head unit Peugeot 307 (>2005) Peugeot 607 (>2005) Peugeot 807 (>2005) Peugeot 407 (>2005) Peugeot 207 (>2006) Peugeot 308 (>2007) Peugeot 307sw (>2005) Peugeot 407sw (>2005).
Installation Guide: Caution : Before the installation of DMC, you need make sure the cd changer option of Citroen or Peugeot head unit is been set on. Otherwise you need go to dealer to open the cd changer option. 1. Before the installation, power off the car 2. Plug the Digital Music Changer into your car stereo changer port (usually located behind the radio) 3. Insert the USB disk or SD Card (Please consult user manual about setting music files in the USB disk or SD Card) 4. For PC, PSP, MD, Mobile Phone etc aux device, connect it with Aux in port 5. Once the unit is installed, power on the radio, then press the Source button, you will then have the following control: Disk+/Disk-, Next track, Previous track, Fast Forward & Fast Rewind etc.… Read More

PEUGEOT 407 e253 CAR ALARM CONTROL UNIT

Filed Under (Peugeot) by admin on 01-01-2014

Download
LOCATION OF THE CAR ALARM CONTROL UNIT Compact control units and sirens: place under the bonnet on the wheel box on the driver’s side. Modular control units and accessories: place under the dashboard on the driver’s side. CAR ALARM SUPPLY Positive: Connect the Can Bus connector in the kit of accessories supplied with the e253 (see instructions for its connection in following pages). Power is taken from the Red wire (Pos. 1). Negative: Connect the Can Bus connector in the kit of accessories supplied with the e253 (see instructions for its connection in following pages). Earth is taken using the Black wire (pos. 2) IMMOBILISER Starter Motor: Cut the White wire (Pos 3) in the Black 3-pin connector under the steering wheel. ODOMETER Connect to pos 26 (Wire N° 6739) in the black 40 way connector (green part) on the BSI control unit or directly to the ABS control unit under the bonnet next to the battery in pos.… Read More

2005 PEUGEOT 407 SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS

Filed Under (Peugeot) by admin on 26-11-2013

Download
GENERAL CONNECTIONS FOR INSTALLATION ALARM/SIREN POSITION Position the compact alarms and the sirens under the dashboard driver’s side. Pass the cables using the original fairlead located behind the servobrake group. POWER SUPPLY +30: connect to the 3 mm2 YELLOW wire, at the position nr. 2, of the 2 way grey/black connector, on the coming out of the anterior part of the “BSI” central. As alternative it is possible to connect to a 8 mm2 threaded pin located in the anterior part of the fuse box. -31: connect directly to one of the ground terminals located under the dashboard, driver’s side. IGNITION WIRE +15/54: connect to 1 mm2 LEIGHT BLUE wire marked “77C”, in the grey connector located inside the tinned box in the engine compartment, driver’s side. DIRECTION INDICATORSConnection right direction indicator Connect to the 0,75 mm2 GREY wire marked 2345, in the black connector marked “GRIS” located inside the tinned box in the engine compartment, driver’s side.… Read More

2007 Peugeot Expert Clarion 2-DIN BKX-1040-11

Filed Under (Peugeot) by admin on 21-11-2013

Download manual for: Peugeot 207 / 307 2007, Fiat scudo 2007, Peugeot Expert 2007, Citroën Jumpy / C2 / C3 2007.
Installation kit includes the following items: * 1X 2-ISO 110 mm. metal bracket * 1X Radio trim * 2X Mounting plates * 2X Mounting spacers * 2X Radio removal keys * 4X Screws * 2X Cushion.
2-DIN BKX-1040-11 * Mount the plates. Use this hole Use this hole We advice to use the following positions. Other positions are also possible. Use position 2 marked with a cross. Use position 12 & 14 marked with an arrow. Measured from left to right. We advice to use the following positions. Other positions are also possible. Use position 2 marked with a cross. Use position 14 & 16 marked with an arrow Measured from left to right. Remove radio by using the original radio keys. Remove the storage bin. Place the 2-Din metal bracket.… Read More

2003 Escape Front Drive Halfshafts DISASSEMBLY AND ASSEMBLY Manual Instructions

Filed Under (Ford) by admin on 13-03-2014

Download Special Tool(s) CV Boot Clamp 205-343 (T95P-3514-A) Disassembly 5. Separate the tripod joint from the inboard CV joint housing. 1. Remove the halfshaft. For additional information, refer to Halfshaft in this section. 2. Secure the halfshaft and constant velocity (CV) joint in a vise using protective jaw covers. 6. If reinstalling the original tripod joint, mark the tripod joint and the halfshaft to make sure of correct installation. 3. Remove the inboard halfshaft boot clamps. 4. Slide the inboard halfshaft boot off the inboard CV joint housing. 7. Remove the snap ring. 11. Remove the two outboard halfshaft boot clamps. 8. Remove the tripod joint. 12. Slide the outboard halfshaft joint boot back out 9. Remove the snap ring. of the way exposing the outboard CV joint. 10. Remove the inboard halfshaft boot from the halfshaft. 13. If reinstalling the original outboard CV joint, mark the outboard CV joint and halfshaft to make sure of correct installation.… Read More

Citroen/Peugeot Sony CDX-T69 Part No. PUGS1 Installation Guide

Filed Under (Peugeot) by admin on 02-01-2014

Download
VEHICLE APPLICATIONS This comprehensive interface is compatible with the following vehicle manufacturers: CITROEN This interface is designed for use with the majority of Citroen models from 1998 including C3, C5, Berlingo, Saxo, Xsara & Xsara Picasso. This is compatible with the following standard Citroen head units: Models with Philips/VDO Head Unit: 22RC260/65Z, 22RC220/35Z OR Models with Clarion Head Unit: PU2325A, PU2294C, PU2325B, PU2358A, PU2471A This interface is not designed specifically for use with the Citroen Satellite Navigation system, but in some instances it may work. PEUGEOT This Interface is also designed for use with the majority of Peugeot models ranging from ’98. This is compatible with the following standard Peugeot head units; 106, 306 and 806 models with Philips Head Unit 22RC200/35/65 or Clarion Head Unit PU2294A 206/307 models with Philips/VDO Head Unit 22RC260/65Z, 22RC220/35Z or Clarion Head Unit PU2325A, PU2294C, PU2325B, PU2358A, PU2471A 406 models with Clarion Head Unit PU2184A / PU1633A / PU1646A This interface is not designed specifically for use with the Peugeot Satellite Navigation system, but in some instances it may work.… Read More

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Filed Under (Other Manuals) by admin on 01-01-2014

Download Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) #05-07-30-031: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) – (Nov 11, 2005) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case.… Read More

2008 Peugeot 308 Parrot MKi9000/MKi9100/MKi9200 Installation Guide

Filed Under (Peugeot) by admin on 06-01-2014

Download Compatibility Car models Peugeot 207: > 2006 Peugeot 308: > 2007 Peugeot 307: > 2006 Peugeot 407: > 2006. For Parrot MKi9000 / MKi9100 / MKi9200 Parrot UNIKA : PI090020AA.
The power supply for the UNIKA interface is taken from the power cable of the Parrot MKi. It is important to follow the color code of the power cable wires: the red wire of the kit’s cable corresponds to the permanent 12V supply; the orange wire corresponds to the ignition 12V ; the black wire is for ground ; the yellow wire corresponds to the Parrot mute output. Warning : Connect the ignition to the Parrot car kit if the vehicle is based on a resistive or a K-Bus protocol. Don’t connect the ignition if the vehicle is based on a CAN protocol. On some vehicles, the 12V power wires may be reversed, in which case you must reverse the red and orange wires of the hands-free kit’s power supply.… Read More

You might also likeclose