how to replace ignition key cylinder 2000 cadillac deville

You search Auto repair manual PDF about how to replace ignition key cylinder 2000 cadillac deville, search results will appear below. If search results do not exist, please search by others keyword.

1990-1998 GM Cadillac Deville Ignition Lock Cylinder REMOVAL & INSTALLATION

Filed Under (Cadillac) by admin on 28-03-2014

Download When performing service around Supplemental Inflatable Restraint (SIR) system components or wiring, the SIR system must be disabled. Failure to do so could result in possible air bag deployment, personal injury, or unneeded SIR system repairs. Catera Disconnect the negative battery cable. 1. Remove the steering wheel. 2. Remove the inflatable restraint steering wheel module coil. 3. Insert a small pointed awl or wire into the ignition lock cylinder release pinhole. 4. Pull out the ignition lock cylinder. 5.Fig. Insert a pointed tool into the release pin hole To install: Install the lock cylinder. Look into the hole that receives the lock cylinder on the lower RH side in order to locate the locking lever. 1. Carefully push down on the locking lever using a small flat-bladed tool until an audible click is heard. 2. Place the lock cylinder into the empty hole. 3. 6. Install the inflatable restraint steering wheel module coil.… Read More

2000 Saturn SL2 Conversion Calculator

Filed Under (Saturn) by admin on 01-01-2014

Download IMPORTANT: The important statement at the beginning of the “Ignition Lock Cylinder removal procedure on page 188 in the 2000/2001 Saturn S-Series Body/Electrical Volume II Service Manual is incorrect. Please cross out the important on that page and write in the following important statement. IMPORTANT: When replacing the ignition lock cylinder only, the passlock relearn procedure is not required. 1. Disconnect negative battery cable. 2. Remove lock cylinder bezel from steering column shroud by carefully prying with a thin bladed screwdriver. Zoom Sized for Print 3. Remove shroud fasteners and remove steering column upper and lower shroud panels. 4. Insert key into ignition lock cylinder and rotate to RUN position. ^If ignition lock cylinder can be rotated to RUN position, continue to step 30. ^If ignition lock cylinder cannot be rotated to RUN position, continue with next step. Zoom Sized for Print 5. Using a light hammer and brass drift, tap lightly on the top side of the ignition housing assembly at the location indicated in the illustration, while trying to turn the ignition key.… Read More

1997 – 2001 Infiniti Q45 ENGINE WILL NOT START

Filed Under (Infiniti) by admin on 24-12-2013

Download 2000 – 2001 I30 (CA33) 1999 I30 (CA32) 1999.5 – 2001 QX4 (JR50) 1997 – 2001 Q45 (FY33) 2000 – 2001 G20 (P11) APPLIED VINS: All APPLIED DATES: Start of production SERVICE INFORMATION This bulletin describes and introduces new features of the Infiniti Vehicle Immobilizer System/Nissan Anti-Theft System (IVIS/NATS). The system is standard equipment on each of the applied vehicles listed above. The IVIS/NATS will not allow the engine to start without the use of a registered ignition key. If a vehicle will not start and the Security lamp is on solid, it may be because the ignition keys were not properly registered into the vehicle’s NATS IMMU (Immobilizer control unit). In this case, there will be a “DIFFERENCE OF KEY” code stored in the NATS IMMU. When the NATS ignition key, IMMU, or ECM (ECCS control unit) are replaced, C/U initialization is necessary. It is also necessary when registering keys and as part of many NATS Service Manual diagnostic procedures.… Read More

Ford-Toyota-Lexus 555F Interface Module Wiring Installation Instructions

Filed Under (Ford) by admin on 13-01-2014

Download The 555F interface module is used when installing remote start products in Ford, Toyota and Lexus vehicles equipped with factory immobilizers. The 555F allows for easy interfacing between the remote start and the factory immobilizer, while maintaining the integrity of the OEM system. WIRE CONNECTION GUIDE FOR FORDS RED (+)12V: Connect this wire to a fused (+)12V source. BLUE (-) ACTIVATION INPUT: Connect this wire to the (-) through activation output of the remote start system. 555FCAPSULE: The 555F capsule should be placed on the outside of the antenna ring as close to the ribbon cable as possible. LEARNING THE 555F CAPSULE FOR FORDS To program the 555F capsule for a Ford vehicle, use the procedure that corresponds to the appropriate vehicle year. 1996 and 1997 Ford Vehicles: 1. Install the remote start and make the appropriate wire connections on the 555F. 2. Make sure that the 555F capsule can reach the front of the key cylinder where the key is inserted.… Read More

2003 Kia Rio CYLINDER HEAD Service and Repair

Filed Under (Kia) by admin on 05-03-2014

Download COMPONENT DISASSEMBLY 1. Drain the coolant and disconnect the upper radiator hose. 2. Remove the breather hose (between the air cleaner and the head cover). 3. Remove the air-intake hose. 4. Remove the vacuum hose, fuel hose and coolant hose 5. Remove the cables from the spark plugs . The cables should be removed by holding the boot portion. 6. Remove the ignition coil. 7. Remove the power steering oil pump and bracket. 8. Remove the intake manifold . 9. Remove the heat protector and exhaust manifold assembly. 10. Remove the coolant pump pulley and the crankshaft pulley. 11. Remove the timing belt cover. 12. Remove the timing belt tensioner pulley. 13. Remove the timing belt . 14. Remove the head cover and cam carrier assembly. 15. Remove the cylinder head assembly. The cylinder head bolts should be removed by using Special Tool, Cylinder Head Bolt Wrench, in the sequence as shown in the illustration in two or three steps.… Read More

Various Concerns with Shifter and/or Ignition Key

Filed Under (Other Manuals) by admin on 28-02-2014

Download Models: 2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) Condition Some customers may comment on any of the following concerns: Cause 1 The shifter button may be sticking in the handle. Cause 2 The pin that activates the micro-switch may have moved out of position (refer to illustration above). This causes the micro-switch to fail to engage when the vehicle is placed in Park. If this condition is present, the customer will not be able to remove the key from the ignition. The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter
assembly moves when activating the button.… Read More

2002 Cadillac DeVille DHS V8-4.6L VIN Y

Filed Under (Cadillac) by admin on 31-12-2013

Download 2002 Cadillac DeVille DHS V8-4.6L VIN Y Recall – Fuel Tank Pressure Sensor Malfunction. Product Safety – Fuel Tank Pressure Sensor # 03038A – (03/17/2004) 03038A — Fuel Tank Pressure Sensor 2002-2003 Cadillac DeVille, Seville Equipped with V8 (4.6L) Engine (LD8/L37) 2002-2003 Oldsmobile Aurora Equipped with V8 (4.0L) Engine (L47) 2002-2003 Pontiac Bonneville SSEi This bulletin is being revised to remove the parts restriction on the fuel tank and eliminate the need for the recall identification label. Please discard bulletin 03035, issued October 2003. Condition General Motors has decided that a defect which relates to motor vehicle safety exists in certain 2002-2003 model year Cadillac DeVille and Seville vehicles equipped with a V8 (4.6L) engine (LD8/L37), Oldsmobile Aurora vehicles equipped with a V8 (4.0L) engine (L47), and Pontiac Bonneville SSEi vehicles. The fuel tank pressure sensors in these vehicles are unusually susceptible to malfunctions. If the sensor malfunctions, excessive vacuum can be applied to the fuel tank during self-diagnostic testing.… Read More

2000 Volkswagen Beetle Vehicle starts and stalls

Filed Under (Volkswagen (VW)) by admin on 01-01-2014

Download Vehicle Application: 2000 Volkswagen Beetle 2.0L, GAS, Eng Des AEG 2002 Volkswagen Beetle 2.0L, GAS, Eng Des AZG 2000 Volkswagen Jetta GL 2.0L 2002 Volkswagen Eurovan 2.8L 2000 Volkswagen Jetta GLS 2.0L, Eng Cfg L4, Eng Des AEG 2002 Volkswagen Jetta GL 2.0L, Eng Des AVH 2000 Volkswagen Jetta GLS 2.8L, Eng Cfg V6, Eng Des AFP 2002 Volkswagen Jetta GLS 2.0L, Eng Cfg L4, Eng Des AVH 2001 Volkswagen Beetle 2.0L, GAS, Eng Des AVH 2002 Volkswagen Jetta GLS Wagon 1.8L 2001 Volkswagen Jetta GL 2.0L, Eng Des AEG 2003 Volkswagen Jetta GLS 2.0L, Eng Cfg L4, Eng Des AVH, USA/Canada 2001 Volkswagen Jetta GLX 2.8L 2007 Volkswagen Passat 3.6 3.6L 2002 Volkswagen Beetle 1.9L, DIESEL, Turbo, Eng Des ALH Customer Concern: Vehicle starts and stalls. Trouble code P1570 (17978). The security light is flashing. Tests/Procedures: 1. As of model year 2000, Volkswagen has changed the immobilizer system and the 7 digit PIN numbers are no longer available to the aftermarket.… Read More

1995 Saturn Wagon Ignition Lock Cylinder

Filed Under (Saturn) by admin on 01-01-2014

Download REMOVAL 1. Remove shroud fasteners (5.5 mm hex head) and remove steering column upper shroud panel. 2. Insert key into ignition lock cylinder and rotate to ACC position. 3. Depress the square locking button on the top of ignition module assembly and slide lock cylinder assembly from ignition module housing. INSTALLATION IMPORTANT : Actuator blade within ignition module housing must be in the ACC position to install lock cylinder assembly. If rotated, replace it to the ACC position using needle nose pliers. Installation is the reverse of Removal.Note: Make sure locking button locks into opening lock cylinder module. Torque steering column lower trim cover bolts to 26 in.lbs. (3 Nm)… Read More

Steering Lock Cylinder – Ignition Switch Removing and Installing

Filed Under (Other Manuals) by admin on 09-12-2013

Download Removing – Remove driver’s-side airbag unit and steering wheel. Repair Manual, Body Interior, Repair Group 69 – Remove steering column switches Page 94-37 . – Insert spare or shop key and switch ignition on: access hole will appear in front of switch next to ignition key slot. Installing – Insert length of steel wire or small screwdriver (approx. 2 mm dia.) as far as it will go, as illustrated, and pull lock cylinder out of steering lock housing in direction of arrow. – Ignition switch must be in “ignition on” position. – Push lock cylinder with ignition key all way into steering lock housing and press in firmly until catch engages audibly. – Install steering column switches and steering wheel. Ignition switch, removing and installing Removing Note: It is not necessary to remove the lock cylinder. – Disconnect battery Ground (GND) strap. – Remove driver’s-side airbag unit and steering wheel.… Read More

You might also likeclose