how to replace crankshaft position sensor on 2005 kia sorento

Below are some PDF files about " how to replace crankshaft position sensor on 2005 kia sorento". Please use another keyword if these are not what you look for.

2001 Infiniti QX4 Direct-Hit – Hotline Archive Detail

Filed Under (Infiniti) by admin on 16-12-2013

  Download 2001 Infiniti QX4 Direct-Hit – Hotline Archive Detail

Download Vehicle Application: 2001 Infiniti QX4 3.5L, USA/Canada 2002 Nissan Pathfinder 3.5L, USA/Canada 2001 Nissan Pathfinder 3.5L, USA/Canada2003 Infiniti QX4 3.5L, USA/Canada Customer Concern: The check engine light is on with a trouble code P1140. Tests/Procedures: 1. Check the right side (passenger side) Intake Valve Timing Control Position (IVTCP) sensor for 12 volts on the Black/White wire. 2. Check the IVTCP sensor for a good ground on the Black wire. 3. Scope the Yellow/Green signal wire and look for a square wave signal of around 8 volts. Check the pattern of the right side sensor and if unsure of the pattern, compare it to the left bank sensor. Potential Causes: IVTCP Sensor Wiring — IVTCP sensor wiring/connection. Tech Tips: This code is for the right (passenger) bank IVTCP Sensor or sensor circuit. The right and left bank sensors can be swapped from side to side to see if the code will follow the sensor.… Read More

  Download 2001 Infiniti QX4 Direct-Hit – Hotline Archive Detail

Sorento/Sedona Throttle Position Sensor W/3.5L Engine

Filed Under (Kia) by admin on 09-12-2013

  Download Sorento/Sedona Throttle Position Sensor W/3.5L Engine

Download provides information related to the Throttle Position Sensor (TPS) for Sorento & Sedona models. Some Sorento & Sedona vehicles may exhibit diagnostic trouble codes P0121 and/or P1121. This condition mainly occurs in high ambient or desert areas, and can be related to the occasional increase in contact resistance due to excessive wear of the inner elements of the TP sensor. This bulletin describes the proper service and adjustment procedure for replacing the TP Sensor. – Effective Vehicle Information 2003-2006 Sorento 3.5L 2002-2005 Sedona 3.5L – Parts Information Part Name Previous Part No. New Part No. Throttle Position Sensor 35102 39000 35102 39000FFF – Service Procedure Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly.… Read More

  Download Sorento/Sedona Throttle Position Sensor W/3.5L Engine

2001 Chevrolet Chevy K Silverado Crankshaft Position Sensor Engine Stall

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

  Download 2001 Chevrolet Chevy K Silverado Crankshaft Position Sensor Engine Stall

Download Models: 2001 Chevrolet Silverado, Suburban 2001 GMC Sierra, Yukon XL Equipped with 8.1L V8 (RPO L18 – VIN G) Engine. Condition General Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 2001 model year Chevrolet Silverado, Suburban; GMC Sierra and Yukon XL model vehicles, equipped with an 8.1L V8 (RPO L18 – VIN G) engine. Some of these vehicles have a condition in which the crankshaft position sensor can fail intermittently or permanently. If the sensor fails intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool down period. If the sensor fails permanently, the engine will quit running and will not re-start. Correction Dealers are to replace the crankshaft position sensor. Vehicles Involved Involved are certain 2001 model year Chevrolet Silverado, Suburban; GMC Sierra and Yukon XL model vehicles, equipped with an 8.1L V8 (RPO L18 – VIN G) engine and built within these VIN breakpoints: Subject: 06083 — Crankshaft Position Sensor Engine Stall Models: 2001 Chevrolet Silverado, Suburban 2001 GMC Sierra, Yukon XL Equipped with 8.1L V8 (RPO L18 – VIN G) Engine Year Division Model From Through 2001 Chevrolet Silverado iE100004 1E200999 1F100006 1F116767 1M100002 1M103668 1Z100010 1Z100042 2001 Chevrolet Suburban 1G100001 1G174359 1J100010 1J100058 2001 GMC Sierra 1E100003 1E2012022 1F100004 1F113912 1M100023 1M103669 1Z100013 1Z100026.… Read More

  Download 2001 Chevrolet Chevy K Silverado Crankshaft Position Sensor Engine Stall

2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR

Filed Under (Ford) by admin on 14-02-2014

  Download 2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR

Download SELF-DIAGNOSTICS – EEC-V (DIESEL) -2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR. Perform this test when directed by QUICK TEST. This test is intended to diagnose: Exhaust Backpressure (EBP) Sensor • Wiring Harness Circuits (SIG RTN, VREF & EBP Signal) • Powertrain Control Module (PCM) • 1) DTC P0470 This DTC indicates PCM detected EBP sensor malfunction during KOEO ON-DEMAND SELF-TEST. Possible causes for this DTC are: Faulty EBP Sensor • Open Or Shorted Circuit • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. If EBP reading is less than 18.5 psi, clear DTCs. Repeat KOEO ON-DEMAND SELF-TEST . If DTC is still present, replace PCM. If EBP reading is 18.5 psi or more, go to next step. 2) Check Signal Ground Circuit Turn ignition off. Disconnect EBP sensor connector. Sensor is located on top front of engine.… Read More

  Download 2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR

1997 Buick Riviera Camshaft Position (CMP) Sensor Performance

Filed Under (Buick) by admin on 28-03-2014

  Download 1997 Buick Riviera Camshaft Position (CMP) Sensor Performance

Download 1997 Buick Riviera | Aurora, Riviera (VIN G) Service Manual DTC P0341 Camshaft Position (CMP) Sensor Performance. Circuit Description The camshaft position PCM input is produced by the ignition control module. The ICM produces the camshaft position PCM input by filtering the camshaft position (CMP) sensor pulses when the engine is running and CKP sync pulses are also being received. The PCM uses the camshaft position PCM input pulses to initiate sequential fuel injection and to determine crankshaft position for the misfire diagnostic. The PCM constantly monitors the number of pulses on the camshaft position PCM input circuit and compares the number of camshaft position PCM input pulses to the number of 18X reference pulses and the number of 3X reference pulses being received. If the PCM receives an incorrect number of pulses on the camshaft position PCM input circuit, DTC P0341 will set and the PCM will initiate injector sequence without the camshaft position PCM input with a one in six chance that injector sequence is correct.… Read More

  Download 1997 Buick Riviera Camshaft Position (CMP) Sensor Performance

2001 Mercedes-Benz SLK320 Engine light is on with no acceleration

Filed Under (Mercedes-Benz) by admin on 26-11-2013

  Download 2001 Mercedes-Benz SLK320 Engine light is on with no acceleration

Download Vehicle Application: 2000 Mercedes-Benz ML320 3.2L 2001 Mercedes-Benz E320 3.2L 2001 Mercedes-Benz C240 2.6L 2001 Mercedes-Benz E320 4Matic 3.2L 2001 Mercedes-Benz C320 3.2L 2002 Mercedes-Benz ML320 3.2L Customer Concern: Engine light is on with no acceleration. Fault code is P0120. Tests/Procedures: 1. Connect scan tool and monitor voltages of pedal sensor B37. Signal 1 (Accelerator pedal position: Idle speed):[0.2...0.5] V Signal 2 (Accelerator pedal position: Idle speed):[0.1...0.5] V Signal 1 (Accelerator pedal position:Kickdown):[4.3...4.8] V Signal 2 (Accelerator pedal position:Kickdown):[2.1...2.5] V 2. If voltages are out of specification verify correct reference voltage to sensor by measuring between pins 6 (Black/White wire) and pin 1 (Blue/Grey wire) on pedal sensor connector. Voltage needs to be between 4.75 and 5.25 volts. 3. Test throttle body voltages with scan tool. Potentiometer #2 signal voltage ignition on, accelerator pedal position CTP 0.3-0.9 VDC, WOT > CTP value Potentiometer #1 signal voltage Ignition on, accelerator pedal position CTP 4.0-4.6 VDC, WOT < CTP value.… Read More

  Download 2001 Mercedes-Benz SLK320 Engine light is on with no acceleration

1996 Ford Taurus V6-182 3.0L – Service and Repair

Filed Under (Ford) by admin on 22-03-2014

  Download 1996 Ford Taurus V6-182 3.0L – Service and Repair

Download : Prior to removal of the Camshaft Position (CMP) sensor, set cylinder No.1 to zero degrees Top Dead Center (TDC) of compression stroke. Then note the position of the CMP sensor electrical connector. The installation procedure requires that the connector be located in the same position. 1. Disconnect battery ground cable. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the Powertrain Control Module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. 2. Disconnect engine control sensor wiring connector from CMP sensor. 3. Remove retaining screws and CMP sensor from sensor housing. 4. If removing CMP sensor housing from the cylinder block, proceed with Removal Step 5. If not removing sensor housing, proceed to installation Step 6. 5. Remove hold-down clamp (bolt and washer assembly) . 6. Remove CMP sensor housing from cylinder block.… Read More

  Download 1996 Ford Taurus V6-182 3.0L – Service and Repair

1999 Saturn SL Engine – Driveability Concerns/Cooling System DTC’s Set

Filed Under (Saturn) by admin on 24-02-2014

  Download 1999 Saturn SL Engine – Driveability Concerns/Cooling System DTC’s Set

Download 1999 Saturn SL1 L4-1.9L SOHC VIN 8 Vehicle Level Powertrain Management Computers and Control Systems Coolant Temperature Sensor/Switch (For Computer) Technical Service Bulletins All Technical Service Bulletins Engine – Driveability Concerns/Cooling System DTC’s Set. SUBJECT: Engine Coolant Temperature Sensor Related Diagnostic Trouble Code(s) and/or the Following Conditions: Hard Start, Erratic Idle, Rough Running. Engine Overheating, Low and/or Leaking Coolant, and/or Service Engine Soon Lamp Illuminated. (Replace Engine Coolant Temperature Sensor with New Design Sensor- P/N 21025106) MODELS AFFECTED: 1991-2001 Saturn S-Series vehicles CONDITION: Customers may comment about various driveability and/or engine operating concerns including: hard start, erratic idle, rough running, engine overheating, low and/or leaking coolant, and/or Service Engine Soon lamp illuminated. CAUSE: This condition may be caused by a cracked engine coolant temperature sensor. CORRECTION: Replace engine coolant temperature sensor, inspect and if necessary replace sensor harness connector. Refer to procedure in this bulletin to replace engine coolant temperature sensor and Parts Requirements for specific parts information.… Read More

  Download 1999 Saturn SL Engine – Driveability Concerns/Cooling System DTC’s Set

1999-2003 Ford F-Series 7.3L PowerStroke Edge Juice Module Installation Instructions

Filed Under (Ford) by admin on 17-12-2013

  Download 1999-2003 Ford F-Series 7.3L PowerStroke Edge Juice Module Installation Instructions

Download
Edge Module and Sensor Wire Installation For trucks with fuse box in a different location, an alternate location for mounting will have to be found. One suggestion is to mount the Juice Module on the side of the air filter box. 1. It is strongly recommended when installing electrical devices that both batteries should be disconnected. Use a 13 mm or 8 mm wrench depending on battery style and remove the negative terminal cable end from each battery. 2. Place the Juice module on top of the fuse box as shown in figure 5. After the installation is complete you will use the supplied Velcro® to secure the Juice module to the fuse box. 3. Connect the MAP “Y” connector between the wire harness and the sensor as shown in Figure 6. This connection is located in front of the passenger side of the vehicle in the engine compartment. 4.… Read More

  Download 1999-2003 Ford F-Series 7.3L PowerStroke Edge Juice Module Installation Instructions

2003 Ford Truck Expedition Suspension – Air Suspension Height Sensor Linkage Loose

Filed Under (Ford) by admin on 02-01-2014

  Download 2003 Ford Truck Expedition Suspension – Air Suspension Height Sensor Linkage Loose

Download FORD: 2003-2006 Expedition LINCOLN: 2003-2006 Navigator ISSUE Some 2003-2006 Expedition and Navigator vehicles equipped with an air suspension may exhibit an air suspension height sensor linkage arm disengaging from the suspension ball stud or height sensor rotating arm. This concern typically occurs with the rear sensor (Figure 1) but may occur with the front sensors as well. If this occurs, the symptom will typically be the vehicle leaning to one side, the vehicle sitting too low/high, a harsh ride, and/or an inoperative air suspension. In addition, this concern may result in diagnostic trouble code (DTC) C1725 (air suspension front pneumatic failure) or C1726 (air suspension rear pneumatic failure). ACTION When a linkage arm becomes disengaged, do not re-attach the arm and do not replace the sensor unless broken. Instead, install a revised linkage arm on all three (3) sensor assemblies, even if they have not detached from the ball stud.… Read More

  Download 2003 Ford Truck Expedition Suspension – Air Suspension Height Sensor Linkage Loose

You might also likeclose