Ford C-4 Trans-Brake Reversed Pattern Manual Installation Instructions

Download Recommended Options: 72803 6 Clutch Drum Assembly 72203 Direct Clutch Kit (6) Blue List of Enclosed Parts (1) Valve Body Assembly (1) Billet Intermediate Servo Cover (1) Solenoid Mounting Block (1) Solenoid Mounting Clip (1) 5/16-18 X 5/8 Whiz Lock Bolt (Solenoid Mounting) (1) Brake Valve (1) Brake Valve Spring (1) Solenoid and Pin Note: Prior to beginning installation of this Trans-Brake kit it is recommended that you be knowledgeable in the assembly of your transmission. If necessary consult a manual or seek the advice of a transmission shop. The transmission must be properly rebuilt for racing before installation of this Trans-Brake. 1.Remove the transmission pan and existing valve body. 2.Ford designates its intermediate servos by letters which appear on the servo cover (A, H, R, K, O, etc.). Note this designation, if your transmission is equipped with a “K” or “R” servo it must be replaced with a servo which has a larger diameter that seals in the bore of the case rather than the bore in the cover.… Read More

2005 Dodge Truck Dakota TRANSMISSION SOLENOID/TRS

Download The transmission solenoid/TRS assembly is internal to the transmission and mounted on the valve body assembly. The assembly consists of six solenoids that control hydraulic pressure to the six friction elements (transmission clutches), and the torque converter clutch. The pressure control solenoid is located on the side of the solenoid/TRS assembly. The solenoid/TRS assembly also contains five pressure switches that feed information to the TCM. OPERATION SOLENOIDS Solenoids are used to control the L/R, 2C, 4C, OD, and UD friction elements. The reverse clutch is controlled by line pressure and the position of the manual valve in the valve body. All the solenoids are contained within the Solenoid and Pressure Switch Assembly. The solenoid and pressure switch assembly contains one additional solenoid, Multi-Select (MS), which serves primarily to provide 2nd and 3rd gear limp-in operation. The solenoids receive electrical power from the Transmission Control Relay through a single wire. The TCM energizes or operates the solenoids individually by grounding the return wire of the solenoid as necessary.… Read More

1999 Ford EXPLORER TRANSMISSION SLIPPING SHIFT/DELAYED

Download FORD: 1999 EXPLORER, RANGER MERCURY: 1999 MOUNTAINEER 6. Inspect the fluid pan for major contamination. ISSUE Slipping transmission shifts and/or delayed or no •If contamination is minimal, clean the main transmission engagements may occur on some control, but do not replace. vehicles. The Electronic Pressure Control (EPC) •If major contamination is present, perform solenoid may cause stress on the attaching bracket. normal transmission overhaul as required, This stress causes the bracket to break and the including main control replacement. Pay EPC solenoid to back out of its bore causing line particular attention to the condition of the pressure to drop too low or fluctuate, allowing friction plates. Repair as required. friction clutches to slip. 7. After repairs are completed, verify concern has ACTION been fixed. Diagnose and inspect for damaged EPC attachment PART NUMBER PART NAME bracket, and replace the bracket and EPC solenoid with new bracket and revised EPC solenoid.… Read More

Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit

Download DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit) Models: 1999-2007 Chevrolet Silverado (Classic) Models 1999-2007 GMC Sierra (Classic) Models 2007-2009 Chevrolet Silverado Models (Excluding Hybrid) 2007-2009 GMC Sierra Models (Excluding Hybrid) This bulletin is being revised to provide an updated picture of the remote filter box and to add an important statement to not replace the EVAP canister. Please discard Corporate Bulletin Number 02-06-04-037E (Section 06 — Engine/Propulsion System). Condition Some customers whose vehicles are operated in dusty type environments, such as farming or mining off*road type applications, may comment about the illumination of the check engine light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set. Cause Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition. Correction (1999-2007 Classic/Old Style Models) After following the published SI diagnostics for P0446 and determining that the EVAP canister vent valve is the cause of the MIL light, replace the existing EVAP canister vent valve assembly with a new assembly.… Read More

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Download Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) #05-07-30-031: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) – (Nov 11, 2005) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case.… Read More

2003 Cadillac Escalade Code C0660 will reset.

Download Vehicle Application: 2003 Cadillac Escalade 5.3L, Vin T, USA/Canada 2005 Chevrolet Suburban 1500 LS 5.3L, GAS, Vin T 2003 Cadillac Escalade EXT 6.0L 2005 GMC Yukon XL 1500 Slt 5.3L, FLEX, Vin Z 2005 Chevrolet Suburban 1500 LS 5.3L, FLEX, Vin Z Customer Concern: Code C0660 will reset. Tests/Procedures: 1. Check the RTD fuse located in the underhood fuse block. 2. Check for Battery Voltage (B+) on the Orange wire at the automatic level control air compressor pin F. 3. If less than B+ at pin F, check for a wiring and connection problem between the air compressor and the underhood fuse block. 4. Disconnect the compressor leveling module connector and check the resistance from the positive battery voltage circuit of the exhaust solenoid valve and the control circuit of the exhaust solenoid valve. Should be 30-90 ohms. 5. Check for B+ on the Dark Blue wire pin B at the air compressor with the exhaust solenoid commanded off.… Read More

2000 AUDI A4 PES G2 SUPERCHARGER SYSTEM INSTALLATION MANUAL

Download Prior to installing the PES G2 supercharger system there are a few steps that are recommended to make the installation as safe and easy as possible. ? Make sure that the engine is completely cool. ? The car should not have been started for at least 2 hours to minimize any residual fuel pressure. This will reduce the fuel leakage that occurs while removing the fuel injectors. ? Remove the negative battery cable from the battery terminal before and during the installation procedure. ? Please save all parts and fasteners you remove from the car during installation. The system has been engineered so that the car may be returned to its stock configuration if so desired. INSTALLATION 1) Disconnect the negative battery terminal. 2) Remove all plastic engine covers. 3) Remove ECU and send it to PES for chip conversion. (See picture 1-3) 4) Remove air box intake ducts. 5) Disconnect PCV tube from passenger side valve cover.… Read More

1997-2002 FORD EXPEDITION REPEAT AIR SUSPENSION COMPRESSOR DRIER FAILURES

Download Some 1997-2002 Expedition 4X4 and 1998-2002 COMPONENTS AS HIGH PRESSURE IS VENTED Navigator 4X4 vehicles equipped with 4-wheel air UNCONTROLLED. suspension, may exhibit repeat air compressor drier If diagnostics lead to compressor/dryer assembly failures. The drier cap may become detached from replacement, use the following service procedure to the drier body, or the drier body may be broken at insure complete and thorough service. the neck near the compressor head. This may be due to incomplete or incorrect system diagnosis that 1. Using the New Generation STAR (NGS) tester, leads to replacement of only the original air vent the compressor/drier assembly. suspension compressor, despite the fact that the compressor is not the root cause of the concern. 2. Using regulated shop air, blow out the air lines Compressor failure in these instances is only a from the drier to the front fill solenoid valve, symptom of an underlying system problem.… Read More