how to replace a blend door actuator 2003 trailblazer

You search Auto repair manual PDF about how to replace a blend door actuator 2003 trailblazer, search results will appear below. If search results do not exist, please search by others keyword.

1999 Chrysler Truck Blend Door Actuator Replacement

Filed Under (Chrysler) by admin on 12-03-2014

Download 1999 Chrysler Truck Town & Country LWB FWD V6-3.8L VIN L Vehicle Level Heating and Air Conditioning Air Door Air Door Actuator / Motor Service and Repair Blend Door Actuator Replacement. REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes.… Read More

2005 HONDA CR-V DOOR VISORS INSTALLATION INSTRUCTIONS

Filed Under (Honda) by admin on 24-12-2013

Download
PARTS LIST Left front door visor Right front door visor Left rear door visor Right rear door visor Installing the Front Door Visor 1. Lower the front door glass completely. Remove the door glass run channel from the door sash in the area shown. Do not remove the glass run channel from the door mirror base or the rear end of the door. AII 27171 TOOLS REQUIRED Isopropyl alcohol Shop towel Masking tape INSTALLATION NOTE: •These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors. Be careful not to damage the paint finish or glass run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours.… Read More

1997-2003 Honda CRV Signal Mirror Manual Installation Instructions

Filed Under (Honda) by admin on 02-02-2014

Download
Door Panel & Mirror Housing Removal 2002-2003 Honda CRV:1. Open door and lower window. 2. Remove plastic cover from corner of door. 3. Pop-out and remove plastic inserts. 4. Remove door handle plastic cover. 5. Unscrew the (2) screws revealed by the removal of the door handle cover. 6. Pry out door handle as shown. Disengage latch behind door handle and remove door handle. 7. Remove the (2) screws beneath armrest. 8. Lift up and pull door panel out slightly as shown. Disconnect any wiring connection behind door panel. Remove door panel from door. 9. Unscrew the (3) nuts holding the mirror housing to the door. Remove mirror housing from door.
Door Panel & Mirror Housing Removal 1997-2001 Honda CRV : 1. Open door and lower window. 2. Remove screw and plastic grommet on inside corner of door. 3. Remove plastic cover from corner of door. 4. Disconnect the mirror wire harness.… Read More

2003 Chevy Truck TrailBlazer Cooling System-Electro-Viscous Fan Clutch Operation

Filed Under (Chevrolet (Chevy)) by admin on 07-04-2014

Download 2003 Chevy Truck TrailBlazer 2WD L6-4.2L VIN S Cooling System – Electro-Viscous Fan Clutch Operation. Subject: Operating Characteristics of the Electro-Viscous (EV) Fan Clutch and Diagnostic Tips for Cooling Fan Noise, Delayed Transmission Shifts and/or Engine Revving Too High Models: 2004-2006 Buick Rainier 2002-2006 Chevrolet TrailBlazer, TrailBlazer EXT 2006 Chevrolet TrailBlazer SS 2002-2006 GMC Envoy, Envoy XL 2004-2005 GMC Envoy XUV 2002-2004 Oldsmobile Bravada 2005-2006 Saab 9-7X with 4.2L I-6, 5.3L V-8 or 6.0L V-8 Engine (VINs S, P, M, H – RPOs LL8, LM4, LH6, LS2) Date/VIN Breakpoints for Vehicles with New EV Fan Clutch. Vehicles built after and including the Date or VIN Breakpoints listed in the table shown are equipped with the new electro-viscous (EV) fan clutch . Vehicles of any model year listed in “Models Affected” with labor code J3390 (claimed after June 8, 2005) with P/N 15293048 in Claim History may also be equipped with this new EV fan clutch .… Read More

Service 4WD Light Illuminated, DTC C0374 Set (Inspect Wiring Harness to Transfer Case Speed Sensors, Replace Wiring Harness)

Filed Under (Other Manuals) by admin on 01-01-2014

Download Models: 2004-2007 Buick Rainier 2003-2006 Chevrolet Avalanche, Suburban, Tahoe 2003-2007 Chevrolet Silverado Classic, TrailBlazer, TrailBlazer EXT 2003-2006 GMC Yukon, Yukon XL 2003-2007 GMC Envoy, Envoy XL, Sierra Classic 2003-2004 Oldsmobile Bravada 2005-2007 Saab 9-7X with Four Wheel Drive or All-Wheel Drive and Active All-Wheel Drive (RPO NP4) or Active Two-Speed (RPO NP8) Transfer Case. Condition Some customers may comment on intermittent illumination of the Service 4WD light. Upon investigation, the technician may find DTC C0374 set. The customer may also comment on intermittent erratic operation of the 4WD or AWD system after driving through rain/snow or simply going through a car wash. Cause The speed sensor signal may have become corrupted. Possible openings in the speed sensor wire insulation (twisted pairs) can allow water intrusion. Also, wire connections contaminated by water may result in short circuits and erroneous speed sensor readings. This most often occurs on the rear speed sensor circuit.… Read More

1999-2003 FORD SUPER DUTY F SERIES HIGH PRESSURE OIL PUMP LEAK

Filed Under (Ford) by admin on 18-12-2013

Download FORD: 1998-2003 E SERIES 1999-2003 SUPER DUTY F SERIES 2000-2003 EXCURSION, F-650, F-750 This article supersedes TSB 03-21-50 to update the WARNING service procedure and illustration. DO NOT REMOVE OR ATTEMPT TO REPAIR A LEAK AT THE PLUG PICTURED IN LOWER LEFT ISSUE CORNER OF FIGURE 1, OR DAMAGE TO THE Some 1998-2003 E-Series, 1999-2003 Super Duty, PUMP WILL RESULT. 2000-2003 Excursion, and 2000-2003 F650/750 1998-2003 E-SERIES HIGH PRESSURE OIL vehicles equipped with a 7.3L Diesel engine may PUMP ACCESS PROCEDURE (DISASSEMBLY) exhibit an oil leak at the high pressure oil pump outlet fittings and/or end plug (see Figure 1). The 1. Remove the Intake Air Resonator. For leak may appear to be a rear main crankshaft seal, additional information, refer to Section 303-12 in oil pan gasket, or other engine oil leak due to the the appropriate Workshop Manual. drain hole machined in the crankcase valley which allows any oil in the valley to run down the back of 2.… Read More

2001-2006 Toyota Sequoia BACK DOOR POWER WINDOW INOPERATIVE

Filed Under (Toyota) by admin on 10-12-2013

Download 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9.… Read More

2003 Chevy Truck TrailBlazer Water Pump Replacement

Filed Under (Chevrolet (Chevy)) by admin on 26-12-2013

Download 1. Drain the coolant. 2. Remove the fan and shroud. 3. Remove the drive belt . 4. Using the J 41240, secure the water pump pulley and remove the water pump pulley bolts. 5. Remove the J 41240. 6. Remove the water pump pulley. 7. Loosen and remove the water pump bolts. 8. Remove the water pump. 9. Clean and inspect the water pump. 10. Discard and replace the gasket. Installation Procedure 1. Install a new water pump gasket. 2. Install the water pump and secure the water pump with the bolts. Tighten * On the initial pass, tighten the bolts to 4 Nm (35 lb in). * On the final pass, tighten the bolts to 10 Nm (89 lb in). 3. Install the water pump pulley. 4. Install the water pump pulley bolts. 5. Using the J 41240, secure the water pump pulley while tightening the water pump pulley bolts.… Read More

2001 Mazda Truck MPV DX FRONT DOOR DISASSEMBLY/ASSEMBLY

Filed Under (Mazda) by admin on 31-12-2013

Download 1. Lower or raise the front door glass so that the distance from the top of the front door glass at the rear end to the upper part of the front molding is 185 mm {7.3 in} 2. Disconnect the negative battery cable. 3. Remove the front door trim.4. Disassemble in the order indicated below. 1. Inner handle 2. Front door trim bracket 3. Door screen 4. Front door glass 5. Front manual window regulator 6. Front power window regulator 7. Glass run channel 8. Front door lock 9. Outer handle 10. Door key cylinder 11. Door weatherstrip 12. Door lower weatherstrip 5. Assemble in the reverse order of disassembly. Front Door Glass Disassembly Note 1. Remove the front door glass installation bolts. 2. Slant the front door glass as shown, and remove the front door glass from the inside of the front door. Outer Handle Assembly Note 1. Connect the door key cylinder harness of outer handle as shown.… Read More

2003 Chevrolet Tahoe Test Details

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download  2002 Chevrolet Silverado 1500 4.8L, GAS, Vin V, Eng Cfg V8, USA/Canada 2003 Chevrolet Tahoe 4.8L, GAS, Vin V 2003 Chevrolet Silverado 1500 4.8L, GAS, Vin V, Eng Cfg V8 2003 Chevrolet Tahoe 5.3L, FLEX, Vin Z Customer Concern: The engine runs, but lacks power when driving. Has codes P0101 and P0300. Scanner shows misfires all on the same side of the engine. Tests/Procedures: 1. Check the catalytic converter, on the “suspect” bank of the engine, for a restricted (plugged) exhaust system to that side of the engine. 2. Disconnect both front O2 sensors, re-set the fuel trims and see if the problem goes away. 3. If gone with the O2 sensors disconnected, then swap the sensors side to side and see if the problem follows the O2 sensor. Potential Causes: Plugged Exhaust System Oxygen Sensor Diagnostic Codes: P0101, P0300 Author: Christopher Pittman Average Reported Mileage: 92479 Confirmed Fix Summary Confirmed Fix 9 – Catalytic Converter 1 – Exhaust System 1 – Intake Manifold Gasket(s) 1 – Right Catalytic Converter Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Phil Zeuner March 04, 2009 2003 Chevrolet Tahoe, 5.3L, FLEX, Vin Z Replaced Catalytic Converter – Replaced cat.… Read More

You might also likeclose