how to remove the shift linkage on infiniti g20

You search Auto repair manual PDF about how to remove the shift linkage on infiniti g20, search results will appear below. If search results do not exist, please search by others keyword.

2002 Chrysler 300M Special GEAR SHIFT CABLE – FLOOR / REMOVAL

Filed Under (Chrysler) by admin on 10-12-2013

Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More

1996-1999 Audi A4/1998 VW Passat Short Shifter Installation Instructions

Filed Under (Audi) by admin on 18-02-2014

Download The following parts are included in this package: – Shifter – Shift Linkage Bracket The following tools are recommended for installation: – 13mm socket and ratchet – 10mm socket and ratchet – socket wobble (universal joint) attachment – socket extension – snap ring / circlip pliers – 6mm allen socket head bit – flexible plunger-type four-claw retriever – torx T-25 driver (only for 2000 A4, S4 and A6 Biturbo) Installation Tips Familiarizing yourself with the short shifter pieces will help make the installation process very easy. Take the time to study each of the pieces that make up the short shifter and read through the installation instructions before you begin. Step 1 – Remove shift knob Step 2 – Remove shift boot Pry up the edges of the shift boot with fingertips, remove from console. Step 3 – Remove black plastic collar Step 4 – Remove circlip Use circlip pliers to remove circlip from shift lever.… Read More

1994 Ford Mustang Heating and Defrosting REMOVAL AND INSTALLATION

Filed Under (Ford) by admin on 31-12-2013

Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More

Audi A4 B6/8E 5 Speed Short Shifter Installation Manual

Filed Under (Audi) by admin on 21-12-2013

Download A. Required Tools Safety Glasses (! See Warnings!) Circlip Pliers Hose Clamp Cutter Razor Blade Ratchet 3/8 or 1/4 Inch Drive Sockets Metric 3/8 or 1/4 Drive (7mm & 10mm) Extension Medium Length 3/8 or 1/4 Inch Drive 6mm Allen Key 6mm Allen Socket 2.5mm Allen key (Included in kit) T-25 Torx Driver 10mm Wrench 24mm or Adjustable Wrench. Step 1: Removal of console cover plate and shift knob. To remove the cover plate, open the ashtray and pull up on the front of the cover. Do the same for the rear of the cover by lifting from within the shift boot at the rear side. To remove the shift knob you must cut the clamp holding the shift knob we have included a new one in the kit. (! Safety glasses are required while cutting the hose clamp!) Once you have removed the clamp, pull up on the shift knob to remove it.… Read More

1991 Infiniti G20 AXLE SHAFTS FRONT

Filed Under (Infiniti) by admin on 21-02-2014

Download 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts. REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose.… Read More

2002 Acura RSX-Type S Short Throw Shift Adapter Installation Manual

Filed Under (Acura) by admin on 09-12-2013

Download 1. Pull down chrome collar and carefully unscrew and remove the stock shift knob. 2. Remove the front console cover. Pull up from the front to unclip the clips and remove from the vehicle. 3. Remove the 2 screws securing the front part of the console. Remove any additional screws that may be holding the center part of the console in place, this may vary by year and model. Lift the 2 tabs shown to the right over the center section of the console so that they rest on the outside of the console assembly. 4. Spread the front sections of the console away from the center console to unclip the 2 clips securing them in place. This may be simplified by pushing from the inside with a hard object next to the clip. 5. Pull the center console to the rear of the vehicle ensuring the sides of the front section of the console remain apart and out of the way.… Read More

1988 Jeep Cherokee Clutch Hydraulic Installation Guide

Filed Under (Jeep) by admin on 02-01-2014

Download
REMOVAL & INSTALLATION TRANSMISSION Removal 1) Remove the shift knob and lock nut from transmission and transfer case shift levers (if equipped). On Wrangler models, remove screws attaching transmission and transfer case shift lever boots and remove both boots. 2) On all other models, raise outer gearshift lever boot and remove upper part on center console. Remove lower part of console, remove inner boot and gearshift lever. 3) On Wrangler models, remove transmission shift tower dust cover. Remove transmission shift lever and stub shaft. DO NOT remove shift lever from stub shaft. 4) On all models, raise and support vehicle. Drain transmission lubricant. Mark rear drive shaft for reassembly and remove rear drive shaft. Support transmission assembly and remove crossmember. Disconnect speedometer cable and wiring from back-up light switch. 5) On 4WD models, drain transfer case lubricant. Disconnect transfer case vacuum hoses and linkage. Tag vacuum hoses for reassembly. Disconnect front drive shaft and secure out of way.… Read More

2002 Land Rover Freelander Camshaft Timing Belt Service Repair

Filed Under (Land Rover) by admin on 10-12-2013

Download Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated. Align Front Timing Belt. 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate.… Read More

1990-1993 Acura Integra TWM Performance Short Throw Shifter Installation Manual

Filed Under (Acura) by admin on 12-02-2014

Download 1. Unscrew the stock shift knob by rotating it counter clockwise. 2. Remove all screws securing center console and remove console. 3. Remove the rubber dust boot surrounding the shifter, use caution not to damage it. Put it in a safe place for re-installation later. 4. Place the car up on a lift, or use a jack and jack stands to raise it off the ground. Loosen the nut on the base of the shifter using a 12mm socket and ratchet. You may need to hold the head of the bolt on the opposite side of the shift rod with a wrench to loosen the nut. 5. Remove the bolt from the base of the shifter and lower the shift rod that connected it to the shifter. 6. Remove both bolts securing the shift assembly to the under side of the chassis with a 12mm socket and ratchet. 7. Remove the bolt at the transmission end of the shift rod with a 12mm or 14mm (depending on model) socket and ratchet.… Read More

Audi S4/A6 Biturbo Short Shifter Installation Instructions

Filed Under (Audi) by admin on 26-03-2014

Download included in this package: – Shifter – Shift Linkage Bracket The following tools are recommended for installation: • ¼” ratchet • 10mm open end/box end wrench • 10mm socket • 3/8″ open end/box end wrench • 3/8″ socket or a 2nd 3/8″ box end wrench • flexible plunger-type four-claw retriever • socket wobble (universal joint) attachment • 1/8″ allen hex key wrench • socket extension • 6mm allen socket head bit • snap ring / circlip pliers Installation Tips Familiarizing yourself with the short shifter pieces will help make the installation process very easy. Take the time to study each of the pieces that make up the short shifter and read through the installation instructions before you begin. Step 1 – Remove shift knob Unscrew the shift knob from the original lever. Step 2 – Remove shift boot Pry up the edges of the shift boot with fingertips, remove from console.… Read More

You might also likeclose