1994 Ford Mustang Heating and Defrosting REMOVAL AND INSTALLATION

Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More

2000-2004 Ford Focus ZX3 SVT Suspension Kit INSTALLATION INSTRUCTIONS

DownloadPARTS IN KIT: ITEM # QTY DESCRIPTION SERVICE PART # REPLACEMENT SOURCE 1 2 Spring, rear 2M5Z-5B669-AA Ford Dealer 2 2 Shock, rear 2M5Z-18125-BA Ford Dealer 3 1 Anti-roll bar, rear 1S4Z-5A772-BA Ford Dealer 4 1 Strut, RF 2M5Z-18124-BA Ford Dealer 5 1 Strut, LF 2M5Z-18124-BB Ford Dealer 6 2 Bump stop 2M5Z-3020-AA Ford Dealer 7 2 Spring, front 2M5Z-5310-AA Ford Dealer 8 2 Nut, upper strut piston W700212-S3091 Ford Dealer. TORQUE SPECIFICATIONS: FASTENER TORQUE (ft./lbs.) (EXCEPT WHERE NOTED) Rear shock upper mount nut 13 Rear shock lower mount nut 85 Rear lower control arm to knuckle 85 Rear anti-roll bar to control arm bolts 11 Rear anti-roll bar bushing clamp bolts 35 Upper strut piston nut 35 Strut tower nuts 18 Knuckle to strut bolt 66 Front anti-roll bar link to strut bolt 94 Caliper to Knuckle 21 Wheel nuts 37. REAR SUSPENSION INSTALLATION INSTRUCTIONS: STEP 1: Raise vehicle off ground and support with jack stands.… Read More

FORD TORQUE CONVERTER & TRANSMISSION Installation Instructions

Download REMOVAL Step 1 Before you begin – let vehicle cool for about an hour. Disconnect battery. Raise vehicle and support on jack stands. The higher you raise it, the easier it is to work under. If your installing a new transmission and converter, skip to STEP 3 Step 2 Drain oil from transmission by removing the drain plug. This is a good time to install a TCI® Drain Plug Kit, TCI® #805800. Pans without plug must be slowly removed by freeing one end and allowing bolts on other end to hold pan. The pan will drop down to allow the fluid to run out the end. Use a drain pan to catch fluid. Remove remainder of bolts and slowly lower pan and pour remainder of fluid in drain pan. Replace filter and clean pan and install new pan gasket. (New gaskets and filters available from TCI®). Reinstall pan and torque pan bolts to OEM specs.… Read More

INSTALLATION INSTRUCTIONS FOR PART 99-5812

DOWNLOAD APPLICATIONS FORD Edge 2007-2010 / Expedition 2007-2010 Explorer 2006-2010 / Explorer Sport Trac 2006-2010 F-150 2004-2008 / E Series 2009-10 / F Series 2005-2009 Five-Hundred 2005-2007 / Focus 2005-2007 / FreeStar 2004-2007 Freestyle 2005-2007 / Fusion 2006-2011 Mustang 2005-2009 / Super Duty 2008-2011 Taurus 2008 / Taurus X 2008-2009 MERCURY Monterey 2004-2007 / Milan 2006-2008 Montego 2005-2007 / Mountaineer 2006-2010 Sable 2008-2009 LINCOLN Mark LT 2005-2008. WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • 70-5520 – Ford Harness 2003-up • 70-5521 – Ford Amplified Harness 2003-up • 70-5522 – Ford Sub Harness 2003-up • XSVI-5520 NAV – Ford Interface 2006-up Antenna Adapter: • 40-CR10 – Chrysler/GM Antenna Adapter 2002-up. DASH DISASSEMBLY FORD F-150 2004-2008 LINCOLN MARK LT 2005-2008 FORD EXPEDITION 2007-2010 FORD EDGE 2007-2010. 1 Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap and remove entire panel surrounding the radio and climate controls. (Figure A) Remove (4) 9/32″ screws to remove the factory radio.… Read More

2002 Land Rover Freelander Camshaft Timing Belt Service Repair

Download Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated. Align Front Timing Belt. 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate.… Read More

1996 Ford Taurus With AXOD-E (AX4S)

Download 1996 Ford Taurus V6-182 3.0L Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Valve Body Service and Repair Removal and Installation With AXOD-E (AX4S) REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor.… Read More

2004-2006 Ford Double DIN Installation Kit PART 95-5812 INSTALLATION INSTRUCTIONS

Download FORD Edge 2007-2009 / Expedition 2007-2009 Explorer 2006-2009 / Explorer Sport Trac 2006-2009 F-150 2004-2008 / F Series 2005-2008 Five-Hundred 2005-2007 / Focus 2005-2007 / FreeStar 2004-2007 Freestyle 2005-2007 / Fusion 2006-2009 Mustang 2005-2009 / Super Duty 2008-2009 Taurus 2008-2009 / Taurus X 2008-2009 MERCURY Monterey 2004-2007 / Milan 2006-2008 Montego 2005-2007 / Mountaineer 2006-2009 Sable 2008-2009 LINCOLN Mark LT 2005-2009 Factory Navigation Only: MKX 2007-2009 / Navigator 2007-2009. DASH DISASSEMBLY A B C D E FORD MUSTANG 2005-2009 Remove the small rectangular shifter lever trim panel if equipped . (Figure A) 2 Remove (4) 9/32″screws from the radio to remove. (Figure E) 7 Remove (2) Phillips screws from under the center armrest at the back of the shifter trim panel (includingcup holders). (Figure B) 3 Unclip and remove panel. (Figure B) 4 Unclip and remove the (2) center stack trim panels from the left and right side of the radio and climate controls.… Read More

2006 Ford Pickup F350 Super Duty CYLINDER HEAD – RH SPECIAL TOOLS REFERENCE

Download 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to JACKING & LIFTING . 2. Drain the engine oil. 3. Remove the intake manifold. For additional information, refer to INTAKE MANIFOLD . 4. Remove the evaporator core housing. For additional information refer to CLIMATE CONTROL. 5. Disconnect the wiring harness retainers from the studs. 6. Remove the injection control pressure (ICP) sensor. Fig. 197: Locating Injection Control Pressure Sensor Courtesy of FORD MOTOR CO. 7. If equipped, remove the nut and position the transmission fluid and indicator aside. installation. 8. Remove the bolts, stud bolts and the valve cover. * Clean and inspect the valve cover gasket. Install a new gasket if necessary. Fig. 199: Locating Valve Cover Bolts Courtesy of FORD MOTOR CO. 9. Remove the high pressure oil rail-to-valve cover gasket. Fig. 200: Identifying High-Pressure Oil Rail-To-Valve Cover Gasket Courtesy of FORD MOTOR CO.… Read More

Ford Escape Power Trailer Wiring Module Installation Instructions

Download Part 1- Configuring the Trailer Wiring Module As stated in the opening paragraph, and the disclaimer above, many trailing light wiring modules (and the one you probably purchased) are configured for installation on the driver’s side of the vehicle. The installer will have to cut the cables between the module and each pre-fabricated taillight connectors. Step 1.1 – Cut the wires between the module and each pre-fabricated taillight connector at a distance 3 or 4 inches from the module. This will leave you ample wire to re-connect them later, after the wires are run through grommets behind the bumper cover. Part 2 – Remove the Rear Bumper Cover (half way) and grommets. Although the rear bumper cover does not require complete removal, the beginner may wish to remove it to facilitate the routing of wires. At a minimum, all fasteners holding the bumper
cover to the body of the vehicle on the passenger side will need to be removed.… Read More

2000-UP FORD FOCUS 4 Door Sedan / Wagon, 3 Door Hatchback Audio Installation Instructions

Download Preliminary: disconnect the negative battery cable. Antenna: the factory antenna is located in the center front of vehicles roof. Radio removal and in-dash installation: note: the factory radio provision is a custom ford double din. When installing an aftermarket din stereo a dash kit is needed. We recommend the scosche fm1375 or fmc1370 installation kit. A set of din removal tools is also needed to remove the factory head unit. We recommend the scosche dt-1 ford din removal tools. 1. Insert ford din removal tools to release clips, pull out stereo, disconnect and remove. Front door speaker installation: note : the factory speaker provision is for a 6 x 8″ speaker. When installing an aftermarket 5 ¼ or 6 ½ speaker, a speaker adapter is required. We recommend the scosche sa68. 1. Extract (7) t-15 torx screws from the perimeter of door panel. 2. Remove screw cover from door opener cup, and extract (1) # 2 philips head screw from behind.… Read More