how to remove ignition lock cylinder on 2004 escalade

You search Auto repair manual PDF about how to remove ignition lock cylinder on 2004 escalade, search results will appear below. If search results do not exist, please search by others keyword.

Steering Lock Cylinder – Ignition Switch Removing and Installing

Filed Under (Other Manuals) by admin on 09-12-2013

Download Removing – Remove driver’s-side airbag unit and steering wheel. Repair Manual, Body Interior, Repair Group 69 – Remove steering column switches Page 94-37 . – Insert spare or shop key and switch ignition on: access hole will appear in front of switch next to ignition key slot. Installing – Insert length of steel wire or small screwdriver (approx. 2 mm dia.) as far as it will go, as illustrated, and pull lock cylinder out of steering lock housing in direction of arrow. – Ignition switch must be in “ignition on” position. – Push lock cylinder with ignition key all way into steering lock housing and press in firmly until catch engages audibly. – Install steering column switches and steering wheel. Ignition switch, removing and installing Removing Note: It is not necessary to remove the lock cylinder. – Disconnect battery Ground (GND) strap. – Remove driver’s-side airbag unit and steering wheel.… Read More

1989 Chevrolet Corvette Steering Column: Service and Repair

Filed Under (Chevrolet (Chevy)) by admin on 02-12-2013

Download 1989 Chevrolet Corvette V8-350 5.7L Steering Column: Service and Repair Disassembly/Assembly SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE Disassembly 1. Remove steering wheel as follows: a. Disconnect battery ground cable, then remove horn cap from steering wheel by pulling. b. Disconnect horn button wire, then remove telescope lever screws and shaft lock knob screw. c. Remove telescope adjustment lever, steering wheel nut retainer and nut. d. Remove steering wheel with a puller. 2. Remove spacer, bumper, spacer and snap ring retainer (Nos. 2, 3, 4, and 5 in Fig. 59 ). 3. Remove shaft lock retainer using lock plate compressor to depress shaft lock. 4. Remove shaft lock and carrier assembly, upper bearing spring, upper bearing seat and inner race. 5. Reverse procedure to install. TURN SIGNAL SWITCH Disassembly 1. Remove SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE as previously outlined.… Read More

1990-1998 GM Cadillac Deville Ignition Lock Cylinder REMOVAL & INSTALLATION

Filed Under (Cadillac) by admin on 28-03-2014

Download When performing service around Supplemental Inflatable Restraint (SIR) system components or wiring, the SIR system must be disabled. Failure to do so could result in possible air bag deployment, personal injury, or unneeded SIR system repairs. Catera Disconnect the negative battery cable. 1. Remove the steering wheel. 2. Remove the inflatable restraint steering wheel module coil. 3. Insert a small pointed awl or wire into the ignition lock cylinder release pinhole. 4. Pull out the ignition lock cylinder. 5.Fig. Insert a pointed tool into the release pin hole To install: Install the lock cylinder. Look into the hole that receives the lock cylinder on the lower RH side in order to locate the locking lever. 1. Carefully push down on the locking lever using a small flat-bladed tool until an audible click is heard. 2. Place the lock cylinder into the empty hole. 3. 6. Install the inflatable restraint steering wheel module coil.… Read More

2000 Volkswagen Cabrio Ignition Switch: Service and Repair

Filed Under (Volkswagen (VW)) by admin on 02-01-2014

Download Steering column, assembly WARNING:Special safety precautions and some different procedures apply to vehicles equipped with airbags CAUTION:Before working on the electrical system: Obtain radio anti-theft code. Ignition OFF ! Disconnect battery Ground (GND) strap. Note: After reconnecting battery: Activate vehicle equipment such as radio, clock and power windows as per service procedures and/or Owner’s Manual. On vehicles equipped with OBD II, activate readiness code. Refer to Powertrain Management, Computers and Control Systems, Testing and Inspection, Procedures See: Powertrain Management/Computers and Control Systems/Testing and Inspection For further information on the steering column assembly, refer to Steering and Suspension, Steering, Steering Column, Service and Repair. 1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig.… Read More

2003 Kia Rio CYLINDER HEAD Service and Repair

Filed Under (Kia) by admin on 05-03-2014

Download COMPONENT DISASSEMBLY 1. Drain the coolant and disconnect the upper radiator hose. 2. Remove the breather hose (between the air cleaner and the head cover). 3. Remove the air-intake hose. 4. Remove the vacuum hose, fuel hose and coolant hose 5. Remove the cables from the spark plugs . The cables should be removed by holding the boot portion. 6. Remove the ignition coil. 7. Remove the power steering oil pump and bracket. 8. Remove the intake manifold . 9. Remove the heat protector and exhaust manifold assembly. 10. Remove the coolant pump pulley and the crankshaft pulley. 11. Remove the timing belt cover. 12. Remove the timing belt tensioner pulley. 13. Remove the timing belt . 14. Remove the head cover and cam carrier assembly. 15. Remove the cylinder head assembly. The cylinder head bolts should be removed by using Special Tool, Cylinder Head Bolt Wrench, in the sequence as shown in the illustration in two or three steps.… Read More

Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery

Filed Under (Other Manuals) by admin on 26-12-2013

Download Models: 2004 Buick Rainier 2000-2004 Cadillac Escalade 2002-2004 Cadillac Escalade EXT 2003-2004 Cadillac Escalade ESV 1998-2004 Chevrolet Blazer, S-10 Pickup 1999-2004 Chevrolet Silverado 2000-2004 Chevrolet Suburban, Tahoe 2002-2004 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2004 Chevrolet Express 1998-2004 GMC Jimmy/Envoy, Sonoma 1999-2004 GMC Sierra 2000-2004 GMC Yukon, Yukon XL 2002-2004 GMC Envoy, Envoy XL 2003-2004 GMC Savana 2004 GMC Envoy XUV 1998-2004 Oldsmobile Bravada 2003-2004 HUMMER H2. #04-06-03-002: Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery – (Feb 5, 2004) When diagnosing a concern regarding an intermittent vehicle no crank or dead battery, technicians should remove and reinstall the ignition switch using the Ignition Switch Replacement procedure in the Steering Wheel and Column section of SI. The ignition switch may have been misindexed in the steering column during a previous replacement . If the ignition switch is misindexed in one direction, the ignition switch circuits will not be completely open when the ignition switch is in the OFF position with the key removed.… Read More

2000 Saturn SL2 Conversion Calculator

Filed Under (Saturn) by admin on 01-01-2014

Download IMPORTANT: The important statement at the beginning of the “Ignition Lock Cylinder removal procedure on page 188 in the 2000/2001 Saturn S-Series Body/Electrical Volume II Service Manual is incorrect. Please cross out the important on that page and write in the following important statement. IMPORTANT: When replacing the ignition lock cylinder only, the passlock relearn procedure is not required. 1. Disconnect negative battery cable. 2. Remove lock cylinder bezel from steering column shroud by carefully prying with a thin bladed screwdriver. Zoom Sized for Print 3. Remove shroud fasteners and remove steering column upper and lower shroud panels. 4. Insert key into ignition lock cylinder and rotate to RUN position. ^If ignition lock cylinder can be rotated to RUN position, continue to step 30. ^If ignition lock cylinder cannot be rotated to RUN position, continue with next step. Zoom Sized for Print 5. Using a light hammer and brass drift, tap lightly on the top side of the ignition housing assembly at the location indicated in the illustration, while trying to turn the ignition key.… Read More

1995 Saturn Wagon Ignition Lock Cylinder

Filed Under (Saturn) by admin on 01-01-2014

Download REMOVAL 1. Remove shroud fasteners (5.5 mm hex head) and remove steering column upper shroud panel. 2. Insert key into ignition lock cylinder and rotate to ACC position. 3. Depress the square locking button on the top of ignition module assembly and slide lock cylinder assembly from ignition module housing. INSTALLATION IMPORTANT : Actuator blade within ignition module housing must be in the ACC position to install lock cylinder assembly. If rotated, replace it to the ACC position using needle nose pliers. Installation is the reverse of Removal.Note: Make sure locking button locks into opening lock cylinder module. Torque steering column lower trim cover bolts to 26 in.lbs. (3 Nm)… Read More

2004-2006 Chevrolet Malibu Loss of Power Steering Assist

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap) Models: 2004-2006 Chevrolet Malibu, Malibu Maxx with 3.5L Engine (VINs 8, N — RPOs LX9, LZ4) Condition Some customers may comment on a loss of power steering assist at high RPM (above 3500 RPM) and a power steering warning message displayed in the DIC. They may also comment some instrument/radio displays are erratic. Upon investigation, the technician may find DTC C0900 set. If the displays were erratic, then DTC B1325 will also be set. Cause This condition may occur when the system voltage exceeds 16 volts for one second for code C0900 and the system shuts down to protect it from over-voltage operation. If the voltage exceeds 18 volts for five seconds for code B1325, then other electronic systems protect themselves and shut down. It has been found that this voltage increase is caused by an interaction between the alternator and the ignition coil/module assembly.… Read More

Ford 2.3 L Engine DISTRIBUTORLESS IGNITION SYSTEM INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 09-02-2014

Download CAUTION: MAKE SURE THE IGNITION SWITCH IS OFF!! The wire from the ignition switch to the ignition coil primary terminal is NOT fused in many applications. If this wire is allowed to touch vehicle or engine ground, with the ignition switch on, it can cause a direct short on the battery possibly causing permanent damage to the vehicle wiring and a fire. Cypress Engineering assumes no liability for damage caused from this occurrence or due to any faults in the existing vehicle wiring. 5. Remove the ignition switch wire from the ignition coil primary positive (+) terminal. Make sure this wire does not come into contact with vehicle or engine ground. 6. Remove the ignition coil and mounting strap from the fan housing and set them aside. 7. Remove the stock distributor and set it aside. 8. Install the Compu-Tronix DIS4-2.3 L Ford Electronic Distributor. Tighten the clamp just enough so that the distributor can still be turned by hand.… Read More

You might also likeclose