Download Compatible with: CITROEN C2/C3/C4/C5/C6 & C8 with Blaupunkt/VDO RD4 head unit PEUGEOT with Blaupunkt/VDO RD4 head unit Peugeot 307 (>2005) Peugeot 607 (>2005) Peugeot 807 (>2005) Peugeot 407 (>2005) Peugeot 207 (>2006) Peugeot 308 (>2007) Peugeot 307sw (>2005) Peugeot 407sw (>2005).
Installation Guide: Caution : Before the installation of DMC, you need make sure the cd changer option of Citroen or Peugeot head unit is been set on. Otherwise you need go to dealer to open the cd changer option. 1. Before the installation, power off the car 2. Plug the Digital Music Changer into your car stereo changer port (usually located behind the radio) 3. Insert the USB disk or SD Card (Please consult user manual about setting music files in the USB disk or SD Card) 4. For PC, PSP, MD, Mobile Phone etc aux device, connect it with Aux in port 5. Once the unit is installed, power on the radio, then press the Source button, you will then have the following control: Disk+/Disk-, Next track, Previous track, Fast Forward & Fast Rewind etc.… Read More
Download Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated. Align Front Timing Belt. 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate.… Read More
Download Citroen C4 1.6Hdi 2004-2009, Citroen Berlingo 1.6L 2005-2009, Citroen C2 1.6Hdi 2005-2009, Citroen C3 1.6Hdi 2008-2009, Citroen C3 Picasso 1.6Hdi 2009, Citroen C4 Picasso 1.6Hdi 2006-2009, Citroen C5 1.6Hdi 2005-2009, Mini Cooper 1.6Hdi 2007-2009, Mini Cooper Clubman 1.6Hdi 2007-2009, Peugeot 207 1.6 2006-2009, Peugeot 308 1.6 2007-2009, Peugeot 407 1.6 2005-2009, Peugeot Partner 1.6 2006-2009.
Parts list: 1 x Air filter Element. 1 x Silicone Intake Hose. 1 x Flexi Cold Air Hose. 1 x Metal Adaptor Hose. 1 x Literature Pack. Fixing Kit :- 3 x Plastic Tie. 3 x #44 Hose Clamp. 1 x Mounting Bracket. 1 x M6 Nylock Nut. 2 x M6 Flat Washer. 1 x Hex Head Bolt M6x20.
Instruction sheet A2054-768 1. Disconnect the negative terminal from the vehicle battery. 2. To the install induction kit it is necessary to remove the bulkhead trims: 3. Unclip & remove the side cover surrounding the washer bottle etc.… Read More
Tools needed: 7mm hose clamp driver T30 screwdriver Phillips head screwdriver 4mm and 5mm allen key/allen socket 10mm socket.
1. Lift the bonnet and begin by undoing the two jubilee clips holding the hose between the airbox and turbo inlet. Pull off the breather to the cam cover and remove the whole hose assembly from the car. 2. Remove the airbox by undoing the single bolt on the left hand side, then pulling it upwards to remove it from the rubber grommets that hold it to the top of the inlet manifold, giving you access to the cold air feed that simply pulls off the right hand side. 3. Remove the MAP sensor from the top of the inlet manifold as shown, then push it firmly into the supplied Forge MAP sensor boss. A little silicon spray will make it easier. Attach the length of silicon vacuum hose supplied to the vacuum nipple on the side of the boss, then reattach the whole assembly back to the inlet manifold with the brass screw provided.… Read More
VEHICLE APPLICATIONS This comprehensive interface is compatible with the following vehicle manufacturers: CITROEN This interface is designed for use with the majority of Citroen models from 1998 including C3, C5, Berlingo, Saxo, Xsara & Xsara Picasso. This is compatible with the following standard Citroen head units: Models with Philips/VDO Head Unit: 22RC260/65Z, 22RC220/35Z OR Models with Clarion Head Unit: PU2325A, PU2294C, PU2325B, PU2358A, PU2471A This interface is not designed specifically for use with the Citroen Satellite Navigation system, but in some instances it may work. PEUGEOT This Interface is also designed for use with the majority of Peugeot models ranging from ’98. This is compatible with the following standard Peugeot head units; 106, 306 and 806 models with Philips Head Unit 22RC200/35/65 or Clarion Head Unit PU2294A 206/307 models with Philips/VDO Head Unit 22RC260/65Z, 22RC220/35Z or Clarion Head Unit PU2325A, PU2294C, PU2325B, PU2358A, PU2471A 406 models with Clarion Head Unit PU2184A / PU1633A / PU1646A This interface is not designed specifically for use with the Peugeot Satellite Navigation system, but in some instances it may work.… Read More
Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More
Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More
Installation manual for: Mitsubishi Outlander 2007 Citroën C-Crosser 2007 Peugeot 4007 2008.
Installation kit includes the following items: * 1X 2-ISO 100 mm. metal bracket * 1X Radio trim * 2X Mounting plates * 2X Mounting spacers * 4X Screws * 2X Radio keys.
We advice to use the following positions. Other positions are also possible. Use position 2 marked with a cross. Use position 11 & 13 marked with an arrow. Measured from left to right. We advice to use the following positions. Other positions are also possible. Use position 2 marked with a cross. Use position 16 & 18 marked with an arrow Measured from left to right. 1. Remove the air shafts with a plastic wedge at the location of the arrows. 2. Remove the 2 screws at the location of the arrows. Remove the dashboard panel. 3. Remove the original radio. This is tighten by four screws.… Read More
Download STEP #1 Evacuate A/C system: • Have your local Air conditioning shop remove the HFC-134a refrigerant from your A/C system. They can reuse your coolant. After the supercharger installation you will need to return the car to them and have them refill and charge the system. This service should cost approximately $80.00. STEP #2 Remove ECM and ship to Hondata: • Remove the battery. • Remove ECM cover (A). • Remove bolts (D), then lift up the ECM. • Disconnect the ECM connectors A, B, and C. • Remove ECM and ship to Hondata (see Address to right.) STEP #3 Drain Coolant: • Jack up and support the front of the car on jack stands. • Make sure the engine is cool and remove the radiator cap. • Drain the cooling system by loosening the drain plug (A) at the bottom of the radiator. • Once all of the coolant is drained close the drain plug.… Read More
Download This Interface is designed for use with the majority of Peugeot models ranging from ’98. This is compatible with the following standard Peugeot head units: 106, 306 and 806 models with Philips Head Unit 22RC200/35/65 or Clarion Head Unit PU2294A 206/307 models with Philips/VDO Head Unit 22RC260/65Z, 22RC220/35Z or Clarion Head Unit PU2325A, PU2294C, PU2325B, PU2358A, PU2471A 406 models with Clarion Head Unit PU2184A / PU1633A / PU1646A This interface is not designed specifically for use with the Peugeot Satellite Navigation system, but in some instances it may work. When connected this interface will allow the audio from an auxiliary input (DVD, MP3 etc) to be played through the vehicles speaker system via the CD mode on the OEM head unit. PRECAUTIONS Vehicles manufactured after 1999 including 206, 307 & 607 may require the head unit initialising by a Peugeot main dealer. INSTALLATION It is important that the installation sequence is followed to ensure complete and proper recognition by the factory head unit.… Read More