2002 Chrysler 300M Special GEAR SHIFT CABLE – FLOOR / REMOVAL

Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More

1982-2003 Ford Mustangs Double Hook Clutch Quadrant and Clutch Adjustment Kit INSTALLATION INSTRUCTIONS

Download DOUBLE HOOK QUADRANT INSTALLATION INSTRUCTIONS: STEP 1: At the bellhousing, remove the plastic splash shield. Use a pry-bar to slacken the clutch cable and disconnect it from the clutch fork. STEP 2: Under the dash, pull the end of the cable loose from the quadrant STEP 3: Under the dash there are two plastic parts that make up the factory clutch quadrant mechanism. They are held in place by clips on the end of the shafts. Remove the clips from the end of the shafts. STEP 4: Press the clutch pedal fully to the floor (you may have to pull the carpet aside) and pry the plastic quadrant and springs off. STEP 5: Press the clutch pedal to the floor again. Align the new aluminum quadrant with the shafts and slide the aluminum quadrant on. Center the quadrant in line with the hole where the cable comes through the firewall.… Read More

Ford C-4 Bracket and Lever Installation Instructions

Download STEP 1. Raise and safely support the vehicle at least 1-2 feet off the ground. Remove the nut and lock- washer holding the downshift linkage onto the downshift lever shaft. The downshift lever is the outer lever on C-4 transmissions. Pull the lever off the shaft and allow the linkage to hang free. Remove and discard stock shift linkage rods. Late C-4 transmissions have a Neutral safety/Backup light switch on the transmission shift lever. If your transmission is so equipped, remove the two bolts holding the switch in place and slide it off the shift shaft. Disconnect the switch at the factory plug and discard it. STEP 2. Install the B&M selector lever, See figure 1 . Note: The B&M lever must point downward for proper operation. If the stock shift lever on your transmission points down, you will have to remove the lower part of the stock arm by cutting it off to clear the B&M lever, (See figure 1 ) .… Read More

2001 Pontiac Grand Prix Shifter A/T: Service and Repair

Download 2001 Pontiac Grand Prix V6-3.8L VIN K. Shifter A/T: Service and Repair Shift Control Replacement Removal Procedure 1. Remove the horseshoe clip (1) from front of shift control knob, and remove knob. 2. Remove the Console Trim Plate. 3. Remove the console wiring harness. 4. Remove the console shift control wiring harness. 5. Remove the automatic transaxle range selector cable. 6. Remove the park/lock cable. 7. Remove the console shift control nuts. 8. Remove the console shift control. Installation Procedure 1. Install the console shift control. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the console shift control nuts. ^Tighten the console shift control nuts to 24 Nm (18 ft. lbs.) . 3. install the park/lock cable. 4. Install the automatic transaxle range selector cable. 5. Install the console shift control wiring harness. 6. Install the console wiring harness. 7. Install the Console Trim Plate. 8. Adjust the transaxle range selector cable.… Read More

2002 Mercury Sable Upper Intake Manifold

Download 1. Remove the air cleaner outlet tube. 2. Remove the pin-type retainers and the accelerator cable splash shield. 3. Disconnect the throttle cable and the cruise control cable. 4. Disconnect the Throttle Position Sensor (TPS) and Idle Air Control (IAC) valve electrical connectors. 5. Disconnect the harness Tom the throttle body stud. 6. Disconnect the Exhaust Gas Recirculation (EGR) vacuum regulator and vacuum supply hoses. 7. Disconnect the Positive Crankcase Ventilation (PCV) and Evaporative Emissions (EVAP) vacuum hoses. 8. Remove the EGR valve. 1 Disconnect the vacuum hose. 2 Remove the nuts. 3 Remove the bolts. 4 Remove the EGR valve. 9. Remove the EGR Vacuum Regulator (EVR) valve. 1 Disconnect the vacuum hose. 2 Disconnect the electrical connector. 3 Remove the bolts. 4 Remove the valve. 10. Remove the eight bolts and the upper intake manifold. * Remove and discard the gaskets. * Clean all mating surfaces. Installation 1.… Read More

2002 Acura RSX-Type S Short Throw Shift Adapter Installation Manual

Download 1. Pull down chrome collar and carefully unscrew and remove the stock shift knob. 2. Remove the front console cover. Pull up from the front to unclip the clips and remove from the vehicle. 3. Remove the 2 screws securing the front part of the console. Remove any additional screws that may be holding the center part of the console in place, this may vary by year and model. Lift the 2 tabs shown to the right over the center section of the console so that they rest on the outside of the console assembly. 4. Spread the front sections of the console away from the center console to unclip the 2 clips securing them in place. This may be simplified by pushing from the inside with a hard object next to the clip. 5. Pull the center console to the rear of the vehicle ensuring the sides of the front section of the console remain apart and out of the way.… Read More

1996-1999 Audi A4/1998 VW Passat Short Shifter Installation Instructions

Download The following parts are included in this package: – Shifter – Shift Linkage Bracket The following tools are recommended for installation: – 13mm socket and ratchet – 10mm socket and ratchet – socket wobble (universal joint) attachment – socket extension – snap ring / circlip pliers – 6mm allen socket head bit – flexible plunger-type four-claw retriever – torx T-25 driver (only for 2000 A4, S4 and A6 Biturbo) Installation Tips Familiarizing yourself with the short shifter pieces will help make the installation process very easy. Take the time to study each of the pieces that make up the short shifter and read through the installation instructions before you begin. Step 1 – Remove shift knob Step 2 – Remove shift boot Pry up the edges of the shift boot with fingertips, remove from console. Step 3 – Remove black plastic collar Step 4 – Remove circlip Use circlip pliers to remove circlip from shift lever.… Read More

1988 Jeep Cherokee Clutch Hydraulic Installation Guide

Download
REMOVAL & INSTALLATION TRANSMISSION Removal 1) Remove the shift knob and lock nut from transmission and transfer case shift levers (if equipped). On Wrangler models, remove screws attaching transmission and transfer case shift lever boots and remove both boots. 2) On all other models, raise outer gearshift lever boot and remove upper part on center console. Remove lower part of console, remove inner boot and gearshift lever. 3) On Wrangler models, remove transmission shift tower dust cover. Remove transmission shift lever and stub shaft. DO NOT remove shift lever from stub shaft. 4) On all models, raise and support vehicle. Drain transmission lubricant. Mark rear drive shaft for reassembly and remove rear drive shaft. Support transmission assembly and remove crossmember. Disconnect speedometer cable and wiring from back-up light switch. 5) On 4WD models, drain transfer case lubricant. Disconnect transfer case vacuum hoses and linkage. Tag vacuum hoses for reassembly. Disconnect front drive shaft and secure out of way.… Read More

2001 Ford Windstar COWL TOP VENT PANEL Installation Instructions

Download 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top vent panel. 2. To install, reverse removal procedure. Tighten bolts and nuts to specification. See TORQUE SPECIFICATIONS . INTAKE MANIFOLD Removal 1. Remove cowl top vent panel. See COWL TOP VENT PANEL . Release fuel pressure and disconnect fuel lines. See FUEL PRESSURE RELEASE & FUEL LINE CONNECTIONS . 2. Disconnect negative battery cable. Drain cooling system. Remove air cleaner assembly and heat tube. Disconnect control cables and linkage at throttle body. Disconnect accelerator cable bracket, and secure aside. 3. Disconnect necessary linkages at intake manifold. Disconnect wiring harness connectors, vacuum hoses, coolant hoses and PCV hoses as necessary. Remove heater tube with fuel lines attached. 4. Remove A/C compressor support bracket (if equipped). Remove throttle body and EGR valve assembly. Note location of upper intake manifold bolts and studs.… Read More

1994 Ford Mustang Heating and Defrosting REMOVAL AND INSTALLATION

Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More