how to remove a transmission shift cable 2003 chevy tahoe

You search Auto repair manual PDF about how to remove a transmission shift cable 2003 chevy tahoe, search results will appear below. If search results do not exist, please search by others keyword.

2002 Chrysler 300M Special GEAR SHIFT CABLE – FLOOR / REMOVAL

Filed Under (Chrysler) by admin on 10-12-2013

Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More

1982-2003 Ford Mustangs Double Hook Clutch Quadrant and Clutch Adjustment Kit INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 23-11-2013

Download DOUBLE HOOK QUADRANT INSTALLATION INSTRUCTIONS: STEP 1: At the bellhousing, remove the plastic splash shield. Use a pry-bar to slacken the clutch cable and disconnect it from the clutch fork. STEP 2: Under the dash, pull the end of the cable loose from the quadrant STEP 3: Under the dash there are two plastic parts that make up the factory clutch quadrant mechanism. They are held in place by clips on the end of the shafts. Remove the clips from the end of the shafts. STEP 4: Press the clutch pedal fully to the floor (you may have to pull the carpet aside) and pry the plastic quadrant and springs off. STEP 5: Press the clutch pedal to the floor again. Align the new aluminum quadrant with the shafts and slide the aluminum quadrant on. Center the quadrant in line with the hole where the cable comes through the firewall.… Read More

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Filed Under (Other Manuals) by admin on 01-01-2014

Download Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) #05-07-30-031: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) – (Nov 11, 2005) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case.… Read More

Ford BD Performance Transmission Installation Instructions

Filed Under (Ford) by admin on 14-01-2014

Download
REMOVAL: 1) Disconnect the negative battery cable(s). 2) Place the transmission into the Neutral (N) position. 3) Raise the vehicle on a hoist. 4) Mark the drive shaft and pinion yokes for assembly alignment. On 4WD models, remove the skid plate. 5) Remove the transmission oil filter tube nut and filler tube. 6) Position a drain pan & disconnect the transmission fluid cooler tubes at the cooler bypass valve. 7) Remove the drive shaft. On 4WD models, remove the front drive shaft & transfer case assembly. On SuperDuty/Motorhome models, remove the transmission mounted parking brake assembly. 8) NOTE: If the vehicle is equipped with a PTO (Power Take-Off) unit, all or part of the PTO will need to be removed. 9) Disconnect the shift cable from the transmission and manual lever. 10) Disconnect the cable housing from the bracket. 11) Disconnect the digital transmission range (TR) sensor connector. 12) Remove the transmission heat shield.… Read More

2000 Chevy Truck S10/T10 Transfer Case Replacement

Filed Under (Chevrolet (Chevy)) by admin on 28-11-2013

Download 2000 Chevy Truck S10/T10 Blazer 4WD V6-4.3L VIN W Vehicle Level Transmission and Drivetrain Transfer Case Service and Repair NVG 233/243-NP1 Transfer Case Replacement. Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 7. Remove any wiring harness from the transfer case. 8. Support the transfer case with a transmission jack. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case. 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case.… Read More

1988 Jeep Cherokee Clutch Hydraulic Installation Guide

Filed Under (Jeep) by admin on 02-01-2014

Download
REMOVAL & INSTALLATION TRANSMISSION Removal 1) Remove the shift knob and lock nut from transmission and transfer case shift levers (if equipped). On Wrangler models, remove screws attaching transmission and transfer case shift lever boots and remove both boots. 2) On all other models, raise outer gearshift lever boot and remove upper part on center console. Remove lower part of console, remove inner boot and gearshift lever. 3) On Wrangler models, remove transmission shift tower dust cover. Remove transmission shift lever and stub shaft. DO NOT remove shift lever from stub shaft. 4) On all models, raise and support vehicle. Drain transmission lubricant. Mark rear drive shaft for reassembly and remove rear drive shaft. Support transmission assembly and remove crossmember. Disconnect speedometer cable and wiring from back-up light switch. 5) On 4WD models, drain transfer case lubricant. Disconnect transfer case vacuum hoses and linkage. Tag vacuum hoses for reassembly. Disconnect front drive shaft and secure out of way.… Read More

FORD TORQUE CONVERTER & TRANSMISSION Installation Instructions

Filed Under (Ford) by admin on 06-02-2014

Download REMOVAL Step 1 Before you begin – let vehicle cool for about an hour. Disconnect battery. Raise vehicle and support on jack stands. The higher you raise it, the easier it is to work under. If your installing a new transmission and converter, skip to STEP 3 Step 2 Drain oil from transmission by removing the drain plug. This is a good time to install a TCI® Drain Plug Kit, TCI® #805800. Pans without plug must be slowly removed by freeing one end and allowing bolts on other end to hold pan. The pan will drop down to allow the fluid to run out the end. Use a drain pan to catch fluid. Remove remainder of bolts and slowly lower pan and pour remainder of fluid in drain pan. Replace filter and clean pan and install new pan gasket. (New gaskets and filters available from TCI®). Reinstall pan and torque pan bolts to OEM specs.… Read More

Ford C-4 Bracket and Lever Installation Instructions

Filed Under (Ford) by admin on 01-09-2012

Download STEP 1. Raise and safely support the vehicle at least 1-2 feet off the ground. Remove the nut and lock- washer holding the downshift linkage onto the downshift lever shaft. The downshift lever is the outer lever on C-4 transmissions. Pull the lever off the shaft and allow the linkage to hang free. Remove and discard stock shift linkage rods. Late C-4 transmissions have a Neutral safety/Backup light switch on the transmission shift lever. If your transmission is so equipped, remove the two bolts holding the switch in place and slide it off the shift shaft. Disconnect the switch at the factory plug and discard it. STEP 2. Install the B&M selector lever, See figure 1 . Note: The B&M lever must point downward for proper operation. If the stock shift lever on your transmission points down, you will have to remove the lower part of the stock arm by cutting it off to clear the B&M lever, (See figure 1 ) .… Read More

1995 Ford Scorpio Transmission Range Sensor Installation Instructions

Filed Under (Ford) by admin on 01-01-2014

Download Remove 1. Move the selector lever to position “N”. 2. Raise the vehicle. 3. Unhook the loops for the rear exhaust pipe. 4. Detach the front heat shield and slide it backwards. 5. Detach the bracket for the front exhaust pipe from the transmission crossmember and swivel it downwards. NOTE: Support the automatic transmission with a transmission jack. 6. Detach the transmission crossmember. 1Detach it from the body. 2Detach it from the automatic transmission. Lower the automatic transmission and remove the transmission jack. 7. Detach the selector lever. 1Unclip the link rod from the selector lever. 2Selector lever 3Nut 4Selector shaft. 8. Disconnect the plug of the TR switch and remove the TR switch. Install NOTE: The guide of the TR switch must engage with the groove of the selector shaft. 9. Install and adjust the TR switch. NOTE: Do not tighten the bolts. 1Attach the TR switch. 2Slide on the selector lever and turn the selector shaft anti-clockwise as far as the stop.… Read More

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Filed Under (Chevrolet (Chevy)) by admin on 29-12-2013

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

You might also likeclose