how to remove 2010 toyota camry front bumper removal

You search Auto repair manual PDF about how to remove 2010 toyota camry front bumper removal, search results will appear below. If search results do not exist, please search by others keyword.

2007 Toyota Camry Rear Bumper Removal and Replacement

Filed Under (Toyota) by admin on 06-04-2014

Download REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.… Read More

1994 Toyota Camry DX TIMING BELT REMOVAL and INSTALLATION

Filed Under (Toyota) by admin on 01-01-2014

Download 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of way. On Camry, remove coolant reservoir tank if it interferes with timing belt removal. Remove engine control (torque) rod from front of engine. 3. On all models, remove accessory drive belts. Using floor jack, slightly raise engine to remove weight from right (timing belt side) engine mount at timing belt cover. 4. Remove right (timing belt side) engine mount and bracket from front of engine. Remove spark plugs. Remove No. 2 timing belt cover and gaskets. See Fig. 1 . 5. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No.… Read More

2009 Ford F150 Rear Bumper W1750 Installation Instructions

Filed Under (Ford) by admin on 31-12-2013

Download I. Overview Congratulations on your new purchase of the industries’ best and most stylish Rear Bumper available for the 2009 Ford F150! This Bumper has been engineered for strength while keeping the weight down. Your Rear Bumper designed in 3-D from digitized data, CNC laser cut, fabricated, and powder coated… all in the U.S.A. Enjoy the fit and finish of a quality Ford F150 Rear Bumper from Fab Fours Inc. II. Tools Required • Socket Wrench with Extension • Breaker Bar • 3/4″ & 18mm Sockets • Flat and Phillips Head Screw Drivers • 3/4″ Box End Wrench • T20 Torx Bit • Floor Jack and wood block. III. Removal of Stock Bumper A. Unplug the Factory License Plate lights from the back side of the light housing from underneath the truck. Turn counter clockwise until loose. Secure up and out of harm’s way. B. Disconnect the wiring harness from the back up sensors.… Read More

2000-2002 FORD FOCUS ZX3 AVENGER BODY KIT INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 04-03-2014

Download Cleaning procedure using a paper towel and grease remover or lacquer thinner, thoroughly clean area on car where the double face tape will come in contact with the painted surface. Do not allow thinner or cloth to remain on car too long as it can cause damage to the painted surface. Using either of the recommended adhesion promoters on a clean lint free cloth, apply a thin, uniform coating to the bonding surface, using the minimum amount that will fully coat the surface. Allow promoter to dry completely before attempting installation of the part. 1) front bumper replacement open the hood and remove the factory clips along the center of the factory front bumper. Remove one screw in each wheel well and also remove the two ten millimeter bolts located on the underside of the bumper. Remove the factory front bumper and discard the styrofoam absorber. Remove the grill from the factory bumper and place it on the new wings west front bumper.… Read More

2009 FIT MUGEN REAR UNDER SPOILER INSTALLATION INSTRUCTION

Filed Under (Honda) by admin on 01-01-2014

Download NOTE: The rear under spoiler cannot be installed on a vehicle equipped with splash guards. PARTS LIST Rear under spoiler 4 Washer bolts (6 x 15 mm) TOOLS REQUIRED Phillips screwdriver Flat-tip screwdriver Hex wrench Drill 5 mm Allen wrench 3 mm, 6 mm and 10 mm Drill bits Clip remover Center punch Pushpin Airsaw Utility knife Felt-tip pen Scale Masking tape Isopropyl alcohol Shop towel Eye protection Blanket INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” NOTE: •Allow the exhaust pipe to cool down before installing this accessory. •Be careful not to damage the rear bumper and the paint finish. •This rear under spoiler kit should be installed only if the ambient temperature is 60°F (15°) or above.… Read More

1995 Mazda MX-6 BRAKE SYSTEM REMOVAL & INSTALLATION

Filed Under (Mazda) by admin on 09-12-2013

Download 1. Raise and support front of vehicle. Remove front wheel assemblies. Remove lower lock pin/guide bolt. See Fig. 2 . Pivot caliper upward and support using rope. 2. Remove pads, shims, guide plates or pad guides and “V” springs (if equipped). Replace pad if lining thickness is less than specified. See MINIMUM PAD LINING SPECIFICATIONS (FRONT) table. 3. To install, reverse removal procedure. Use Disc Brake Expander (49-0221-600C) and an old pad to push piston fully inward to install disc pads. FRONT DISC BRAKE CALIPER Removal & Installation Raise and support front of vehicle. Remove front wheel assemblies and disconnect brake hose. Plug all openings. Remove front disc brake pads. See FRONT DISC BRAKE PADS . Remove remaining mounting bolt(s). Remove caliper from vehicle. To install, reverse removal procedure. Bleed air from system. FRONT BRAKE ROTOR Removal & Installation 1. Raise and support front of vehicle. Remove front wheel assemblies.… Read More

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Filed Under (Chevrolet (Chevy)) by admin on 29-12-2013

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

1994 Ford Mustang Heating and Defrosting REMOVAL AND INSTALLATION

Filed Under (Ford) by admin on 31-12-2013

Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More

Audi S4 Side Mount Intercooler Installation

Filed Under (Audi) by admin on 02-01-2014

Download Lift the car and secure it with jack stands. Ramps will also work. Remove lower engine splash shield. Remove side grilles from bumper. Use a slotted screwdriver through the grille inserts and pry the two tabs behind the inner most edge of each of the inserts. Remove 3 bolts securing each headlight in place. Use caution when removing bolt behind the turn signal bulbs, as they are hard to retrieve if dropped. Disconnect headlight plug. From the turn signal end, pull the headlight forward slightly, and then slide outwards to remove from inner locating dowel. Remove headlight and disconnect turn signal bulb connector. You can also remove the bulb and connector together. Remove two torx screws securing bumper to inner fender liner. One screw per side. Disconnect washer fluid hose Using a 6mm Hex bit, remove bolts (2) securing bumper to bumper shocks. One per side. Pull upwards and outwards on the rear outer corner of the bumper.… Read More

1988 Jeep Cherokee Clutch Hydraulic Installation Guide

Filed Under (Jeep) by admin on 02-01-2014

Download
REMOVAL & INSTALLATION TRANSMISSION Removal 1) Remove the shift knob and lock nut from transmission and transfer case shift levers (if equipped). On Wrangler models, remove screws attaching transmission and transfer case shift lever boots and remove both boots. 2) On all other models, raise outer gearshift lever boot and remove upper part on center console. Remove lower part of console, remove inner boot and gearshift lever. 3) On Wrangler models, remove transmission shift tower dust cover. Remove transmission shift lever and stub shaft. DO NOT remove shift lever from stub shaft. 4) On all models, raise and support vehicle. Drain transmission lubricant. Mark rear drive shaft for reassembly and remove rear drive shaft. Support transmission assembly and remove crossmember. Disconnect speedometer cable and wiring from back-up light switch. 5) On 4WD models, drain transfer case lubricant. Disconnect transfer case vacuum hoses and linkage. Tag vacuum hoses for reassembly. Disconnect front drive shaft and secure out of way.… Read More

You might also likeclose