Various Concerns with Shifter and/or Ignition Key

Download Models: 2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) Condition Some customers may comment on any of the following concerns: Cause 1 The shifter button may be sticking in the handle. Cause 2 The pin that activates the micro-switch may have moved out of position (refer to illustration above). This causes the micro-switch to fail to engage when the vehicle is placed in Park. If this condition is present, the customer will not be able to remove the key from the ignition. The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter
assembly moves when activating the button.… Read More

1990-1993 Acura Integra TWM Performance Short Throw Shifter Installation Manual

Download 1. Unscrew the stock shift knob by rotating it counter clockwise. 2. Remove all screws securing center console and remove console. 3. Remove the rubber dust boot surrounding the shifter, use caution not to damage it. Put it in a safe place for re-installation later. 4. Place the car up on a lift, or use a jack and jack stands to raise it off the ground. Loosen the nut on the base of the shifter using a 12mm socket and ratchet. You may need to hold the head of the bolt on the opposite side of the shift rod with a wrench to loosen the nut. 5. Remove the bolt from the base of the shifter and lower the shift rod that connected it to the shifter. 6. Remove both bolts securing the shift assembly to the under side of the chassis with a 12mm socket and ratchet. 7. Remove the bolt at the transmission end of the shift rod with a 12mm or 14mm (depending on model) socket and ratchet.… Read More

Ford Focus Short SVT M-7210-S Throw Shifter INSTALLATION INSTRUCTIONS

Download REMOVING THE CONSOLE STEP 1: Remove the front cup holders. Remove the Torx screws under the cup holder with a T-20 bit. (Some cars may have Phillips head screws). STEP 2: Remove the rear cup holders. Squeeze the center and pull forward to undo the back tab, then pull straight up to unsnap the cup holder. Remove the nuts holding the rear of the console. STEP 3: Unscrew the shift knob from the shifter. Leave it attached to the leather boot. STEP 4: Pull the parking brake up as far as it will go. STEP 5: Pull up and back to remove the console. Be careful not to scrape the brake handle on the console. STEP 6: Reach underneath the console and disconnect the cigarette lighter plug. REMOVING THE STOCK SHIFTER STEP 7: Place the transmission in 1st gear. Steady the shift lever with one hand and pry the cable off with a screwdriver.… Read More

1996-1999 Audi A4/1998 VW Passat Short Shifter Installation Instructions

Download The following parts are included in this package: – Shifter – Shift Linkage Bracket The following tools are recommended for installation: – 13mm socket and ratchet – 10mm socket and ratchet – socket wobble (universal joint) attachment – socket extension – snap ring / circlip pliers – 6mm allen socket head bit – flexible plunger-type four-claw retriever – torx T-25 driver (only for 2000 A4, S4 and A6 Biturbo) Installation Tips Familiarizing yourself with the short shifter pieces will help make the installation process very easy. Take the time to study each of the pieces that make up the short shifter and read through the installation instructions before you begin. Step 1 – Remove shift knob Step 2 – Remove shift boot Pry up the edges of the shift boot with fingertips, remove from console. Step 3 – Remove black plastic collar Step 4 – Remove circlip Use circlip pliers to remove circlip from shift lever.… Read More

Audi S4/A6 Biturbo Short Shifter Installation Instructions

Download included in this package: – Shifter – Shift Linkage Bracket The following tools are recommended for installation: • ¼” ratchet • 10mm open end/box end wrench • 10mm socket • 3/8″ open end/box end wrench • 3/8″ socket or a 2nd 3/8″ box end wrench • flexible plunger-type four-claw retriever • socket wobble (universal joint) attachment • 1/8″ allen hex key wrench • socket extension • 6mm allen socket head bit • snap ring / circlip pliers Installation Tips Familiarizing yourself with the short shifter pieces will help make the installation process very easy. Take the time to study each of the pieces that make up the short shifter and read through the installation instructions before you begin. Step 1 – Remove shift knob Unscrew the shift knob from the original lever. Step 2 – Remove shift boot Pry up the edges of the shift boot with fingertips, remove from console.… Read More

Audi A4 B6/8E 5 Speed Short Shifter Installation Manual

Download A. Required Tools Safety Glasses (! See Warnings!) Circlip Pliers Hose Clamp Cutter Razor Blade Ratchet 3/8 or 1/4 Inch Drive Sockets Metric 3/8 or 1/4 Drive (7mm & 10mm) Extension Medium Length 3/8 or 1/4 Inch Drive 6mm Allen Key 6mm Allen Socket 2.5mm Allen key (Included in kit) T-25 Torx Driver 10mm Wrench 24mm or Adjustable Wrench. Step 1: Removal of console cover plate and shift knob. To remove the cover plate, open the ashtray and pull up on the front of the cover. Do the same for the rear of the cover by lifting from within the shift boot at the rear side. To remove the shift knob you must cut the clamp holding the shift knob we have included a new one in the kit. (! Safety glasses are required while cutting the hose clamp!) Once you have removed the clamp, pull up on the shift knob to remove it.… Read More

2002 Land Rover Freelander Camshaft Timing Belt Service Repair

Download Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated. Align Front Timing Belt. 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate.… Read More

2010 Hyundai Genesis Coupe Short Shifter Manual Installation Instructions

Download
Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged to install the short shifter on a slightly inclined surface, place wooden blocks in front or behind the wheels to prevent the car from moving while you’re working. Please read this installation manual completely before installing the short shifter. Make sure to let the car cool down before you do the install as you will be working on and around the exhaust line.
INSTALLATION INSTRUCTIONS: 1. Working inside the car, unsnap the shift boot from the shift knob and remove the shift knob by rotating it counter clockwise. Put it aside in a safe place for re-install later. 2. With your fingers inside the shift boot, pull the shifter console up. 3. If you have heated seats, unplug the connector from the console.… Read More

2002 Chrysler 300M Special GEAR SHIFT CABLE – FLOOR / REMOVAL

Download 2002 Chrysler 300M Special V6-3.5L VIN G Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift. 42LE – Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle. 4. Loosen nut on shift cable adjust lever (Fig. 252) 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp.… Read More

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More