how to install breather hose elbow audi a4 2004

You search Auto repair manual PDF about how to install breather hose elbow audi a4 2004, search results will appear below. If search results do not exist, please search by others keyword.

2004 Audi S4 V8 HyperFlow V84 Induction System

Filed Under (Audi) by admin on 15-02-2014

Download for Stratmosphere Audi S4 V8 HyperFlow V84 Induction System (for 2004+ V8 S4s) Step 1- Remove OEM induction runner The factory induction system is on the passenger front corner of the car (right side) . Shown in Figure 1. Remove the black plastic trim at the top of Fig. 1 by pulling up ( 2004 only ). Careful not to break any attachment points. To begin removal of the induction runner, remove the two Phillips head screws at the front of the car (Fig. 2). Once this is complete the runner can be pulled back toward the firewall. The accordion piece and the runner piece by the fender are both separate. Step 2- Remove OEM breather hose, begin airbox removal Loosen the hose clamp as shown in Fig. 3 and then remove the breather hose from the factory airbox. This may be a single use clamp that you must cut to remove.… Read More

1996-2001 Audi A4 Quattro Part 57- 0515 INSTALLATION INSTRUCTIONS

Filed Under (Audi) by admin on 09-12-2013

Download Audi A4 2.4/2.8L V6 1995-2001 Audi A4 Quattro 2.8L V6 1996-2001 Audi A6 2.4/2.8L V6 1997-2002 Audi A6 Quattro 2.8L V6 1997-2001 1. Remove the cover from the air box assembly. (Fig. 1) 2. Unclip the electrical connector from the Mass Air Sensor (MAS). (Fig. 2) 3. Unclip and remove the intake hose from the MAS. (Fig. 3) 4. Unclip the evap control valve from the air box. (Fig. 4) 5. Unclip the wiring from the air box (Fig. 5) 6. Unbolt the air box mounting bolt. (Fig. 6) 7. Disconnect the auxiliary air pump hose from the front of the air box. (Under the intake scoop) 8. Carefully lift and remove the complete air box assembly from the vehicle. (Fig. 7) 9. Unbolt and remove the MAS from the air box. (Fig. 8) 10. Fit the MAS adaptor to the MAS using the hardware provided. (Fig. 9) 11. Refit the MAS to the intake hose using the original hose clip.… Read More

2002-2005 Audi A4 Intake Kit Installation Instructions

Filed Under (Audi) by admin on 05-02-2014

Download Kit Part # 51/54-10322. Complete kit. Make sure you have all the components before you begin your installation. Complete stock intake. a. Remove two screws holding factory fresh air duct in place. b. Pull fresh air duct out of vehicle and save for later use a. Remove two screws holding top half of airbox in place. b. Loosen clamp holding factory tube in place. c. Unplug MAF Sensor Remove top half of factory airbox. Remove clamp holding top breather filter on factory tube. Remove clamps holding second breather from top of factory tube. Save elbow for later use. Remove clamps holding third breather filter from top of factory tube. Plug can be disconnected for ease of removal. Loosen clamp holding fourth breather down from top of tube with slotted screwdriver. Loosen clamp at turbo and Last breather tube. Pull factory tube out of vehicle. Pull off front grill near Passenger side fog lamp.… Read More

HONDA CIVIC LX / DX AEM INTAKE SYSTEM INSTALLATION INSTRUCTIONS

Filed Under (Honda) by admin on 09-12-2013

Download Installation of AEMĀ® intake system. a. When installing the intake system, do not completely tighten the hose clamps or mounting hardware until instructed to do so. b. Remove the transmission mount bracket nut closest to the front of the car. Install the supplied transmission bracket over the stud and replace the nut. Refer to the picture for correct orientation. Torque the transmission mount bracket nut to 54 N-m (5.5 kgf-m, 40 lbf-ft). (Fig. 9) c. Install the 2.50″ x 2″ hose on to the throttle body with two 2.50″ hose clamps. d. Check to see that the inside of the AEMĀ® intake pipes and air filter are clean and free from any foreign objects and/or obstructions. e. Place the primary intake pipe into the hose on the throttle body. The throttle body end is the end with the IAT sensor hole and breather hose nipple. f. Thread supplied washer and bolt through the intake pipe mounting tab into the factory intake resonator mounting bracket.… Read More

2004 Audi A3 Parrot MKi9000/MKi9100/MKi9200 UNIKA Installation

Filed Under (Audi) by admin on 23-12-2013

Download Parrot UNIKA can work with car protocols such as CAN, KBUS or resistive systems. Installation Compatibility Car models Audi A3 : > 2004 Audi A6 : > 2004 Audi A4 : > 2004 Audi Q7 : > 2006 Audi A5 : > 2007 Audi TT : > 2006 For Parrot MKi9000 / MKi9100 / MKi9200 Parrot UNIKA : PI090020AA Parrot reference. The power supply for the UNIKA interface is taken from the power cable of the Parrot MKi. It is important to follow the color code of the power cable wires: the red wire of the kit’s cable corresponds to the permanent 12V supply; the orange wire corresponds to the ignition 12V ; the black wire is for ground ; the yellow wire corresponds to the Parrot mute output. Warning : Connect the ignition to the Parrot car kit if the vehicle is based on a resistive or a K-Bus protocol.… Read More

2000-2003 ACURA TL AEM INTAKE SYSTEM PART 21-416 INSTALLATION INSTRUCTIONS

Filed Under (Acura) by admin on 02-01-2014

Download PART NUMBER: 21-416 2000-2003 ACURA TL V6-3.2L C.A.R.B. E.O. # D-670 2001-2003 ACURA CL V6-3.2L C.A.R.B. E.O. # D-670 1998-2002 HONDA Accord V6-3.0L C.A.R.B. E.O. # D-670. 1. Preparing Vehicle a. Make sure vehicle is parked on level surface. b. Set parking brake. c. If engine has run in the past two hours, let it cool down. d. Disconnect negative battery terminal. e. Do not discard stock components after removal of the factory system. 2. Removal of stock system a. Remove the stock air box assembly and attaching hardware from inside the fender well. b. Disconnect the breather hose and the Fuel Injection Air Control System hose from the air inlet tube. c. Loosen and remove the air inlet tube from the throttle body. d. Raise the front of the vehicle with a jack. Refer to your owner’s manual for proper jack and jack stand placement to properly support vehicle.… Read More

Audi TT A.W.E. Tuning DV1 Diverter Valve

Filed Under (Audi) by admin on 27-12-2013

Download 1.8T Audi TT, VW Golf/Jetta/New Beetle. Step 1: Here’s an overview picture of the transverse 1.8T engine found in the Audi TT, VW Golf/Jetta/New Beetle 1.8T. The 225hp TT engine looks a little different, but the install of the A.W.E. Tuning valve is the same procedure. For picture clarity, and ease of install, the decorative engine cover has been removed. Removing the cover is easily done by twisting the “+” shaped fasteners on the cover 90 degrees. They’ll pop up when free, allowing you to grab the cover and lift it up and out of the engine bay. (New Beetle requires removing 2 10mm nuts hidden under trim caps, and then sliding forward and out) We’ve also removed the PCV damper in the following pictures for clarity. You won’t need to remove this item to install the valve. Installation instructions for A.W.E. Tuning DV1 Diverter Valve For 1.8T Audi TT, VW Golf/Jetta/New Beetle Thank you for purchasing the A.W.E.… Read More

2005 Chevrolet Malibu Service and Repair

Filed Under (Chevrolet (Chevy)) by admin on 09-12-2013

Download Vacuum Brake Booster Check Valve and/or Hose Replacement Removal Procedure 1. Disconnect the brake booster vacuum check valve (1) from the brake booster. 2. If the vacuum check valve (1) needs to be separated from the vacuum hose (3), release and reposition the clamp (2) on the vacuum hose (3) and remove the check valve (1) from the hose (3). 3. If replacing the vacuum check valve (1), remove the grommet (4) from the brake booster and discard the grommet. 4. If removing the vacuum hose (2), take note of the vacuum hose routing then disconnect from the engine intake manifold connection (3) by releasing tension on the vacuum hose clamp (1) and sliding the vacuum hose (2) off the intake manifold connection (3). Installation Procedure Important: A small amount of denatured alcohol can be used as an assembly aid when installing the vacuum check valve and/or grommet. Do NOT use soap.… Read More

2000-2004 Audi TT Coupe Brake System

Filed Under (Audi) by admin on 31-12-2013

Download Audi TT Coupe 2000-2004, Audi TT Roadster 2001-2004 – Brake System. ABS/ESP ITT Mark 20 system components, removing and installing Brake light switch (square housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once. Removing – Remove storage compartment on driver’s side. Repair Manual, Body Interior, Repair Group 68; Storage compartments, covers – Unplug electrical connector. – Remove brake light switch -1- by turning counter-clockwise through 90. Installing Install in reverse sequence; note the following points: – Pull brake light switch plunger fully out. – Press brake pedal down as far as possible by hand. – Guide switch through installation hole and secure by turning 90 clockwise -arrows-. – Release brake pedal. – Make sure proper function of brake lights when brake pedal is pressed and released. Brake light switch (round housing) , removing and installing Note: To ensure a secure fit, the switch may only be installed once.… Read More

1995-1996 Honda Civic V 1.4L L4 Part 57-0527 Installation Manual

Filed Under (Honda) by admin on 27-01-2014

Download
Honda Civic V 1.4L L4 1995-1996, Honda Civic V 1.4L L4 D14A4 Eng 1997-2001, Honda Civic V 1.6L L4 105BHP 1995-2001 (15.09.10)
1. Unclip and remove air box lid from the vehicle. (Fig. 1) 2. Unbolt & remove the resonator box from the vehicle. (Fig. 2) 3. Disconnect the cam cover breather from the air box base. (Fig. 3) 4. Remove the air temp sensor from the side of the air box. (Fig. 4) 5. Loosen the clip on the throttle neck, unbolt and remove the air box base. (Fig. 5) 6. Remove the 2 short breather hoses from the cam cover outlet and the metal breather hose. (Fig. 6&7) 7. Fit the stepped rubber adaptor onto the throttle housing and firmly tighten using the #44 hose clamp supplied. (Fig. 8) (Note: – This adaptor should be a tight fit) 8. Fit the plastic intake tube into the stepped rubber adaptor & firmly tighten using the #60 hose clamp supplied.… Read More

You might also likeclose