how to install blend door actuator on 1998 buick park ave

You search Auto repair manual PDF about how to install blend door actuator on 1998 buick park ave, search results will appear below. If search results do not exist, please search by others keyword.

1999 Chrysler Truck Blend Door Actuator Replacement

Filed Under (Chrysler) by admin on 12-03-2014

Download 1999 Chrysler Truck Town & Country LWB FWD V6-3.8L VIN L Vehicle Level Heating and Air Conditioning Air Door Air Door Actuator / Motor Service and Repair Blend Door Actuator Replacement. REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes.… Read More

2005 HONDA CR-V DOOR VISORS INSTALLATION INSTRUCTIONS

Filed Under (Honda) by admin on 24-12-2013

Download
PARTS LIST Left front door visor Right front door visor Left rear door visor Right rear door visor Installing the Front Door Visor 1. Lower the front door glass completely. Remove the door glass run channel from the door sash in the area shown. Do not remove the glass run channel from the door mirror base or the rear end of the door. AII 27171 TOOLS REQUIRED Isopropyl alcohol Shop towel Masking tape INSTALLATION NOTE: •These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors. Be careful not to damage the paint finish or glass run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours.… Read More

2001-2006 Toyota Sequoia BACK DOOR POWER WINDOW INOPERATIVE

Filed Under (Toyota) by admin on 10-12-2013

Download 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9.… Read More

1998 Buick Park Avenue Engine Coolant Consumption or Coolant Leak

Filed Under (Buick) by admin on 20-01-2014

Download Engine Coolant Consumption or Coolant Leak (Inspect For Material Degradation/Replace Intake Manifolds) Models: 1995-1997 Buick Riviera 1995-1999 Buick LeSabre, Park Avenue 1996-1999 Buick Regal 1998-1999 Chevrolet Lumina, Monte Carlo 1995-1996 Oldsmobile Ninety-Eight 1995-1999 Oldsmobile Eighty-Eight 1998-1999 Oldsmobile Intrigue 1995-1999 Pontiac Bonneville 1997-1999 Pontiac Grand Prix with 3.8L Engine (VIN K — RPO L36) Condition Some customers may comment on excessive engine coolant consumption, or an engine coolant leak near or under the throttle body area of the upper intake manifold. Cause Upper intake manifold composite material may degrade around the EGR stove pipe and could result in an internal or external coolant leak. Correction 1. Follow the upper intake manifold removal instructions found in the Engine Unit Repair Section of the Service Information Manual. 2. Refer to the arrow in the illustration of the upper intake manifold above. Inspect the inner diameter of the EGR passage for signs of material degradation.… Read More

2009 Honda Civic 4-Doors Accessories Door Visors Installation Manual

Filed Under (Honda) by admin on 13-10-2013

Download
TOOLS AND SUPPLIES REQUIRED Isopropyl alcohol Shop towel Masking tape 6 in. Scale
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” NOTE: •Visors may not be legal in all states. Please check the laws of your state. •Be careful not to damage the paint finish and glass run channels when installing the door visors. •Handle the door visors with care. They are not designed to absorb shock or impact. •This door visor kit should only be installed if the ambient air temperature is 60°F (15°C) or above. •To allow the adhesive to cure, do not wash the vehicle for 24 hours. Installing the Rear Door Visor 1. Fully open the left rear door window. 2. Install one bracket (C) and one bracket (D) on the door sash at the measurements shown.… Read More

2004 Buick LeSabre Shake/Vibration in Steering Wheel

Filed Under (Buick) by admin on 31-12-2013

Download 2004 Buick LeSabre | LeSabre (VIN H) Service Manual. Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) Condition Some customers may comment on shaking/vibration in the steering wheel, floor or seat while driving at highway speeds (typically between 60-72 mph (96-115 km/h)) on smooth roads. Cause These specific vehicles may be sensitive to various rotating mass assemblies, especially if they are considered to be out-of-balance. Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights 3.… Read More

2002 Buick Truck Rendezvous Trim Panel Replacement

Filed Under (Buick) by admin on 13-12-2013

Download Tools Required J 38778 Door Trim Pad and Garnish Clip Remover Removal Procedure 1. Open the door. 2. Disconnect the power window switch assembly. 3. Remove the screws from the front door trim panel 4. Use the J 38778 to remove the trim panel. 1. Reposition the electrical harness connectors. 2. Remove the trim panel from the vehicle. Installation Procedure Important: Before installing the front door trim panel , discard the old trim panel retainers and replace with NEW trim panel retainers. 1. Install the new retainers to the front door trim panel . 2. Route the electrical connectors through the trim panel . 3. Align the trim panel to the door inner panel, guiding the door handle through the trim panel. 4. Install the upper edge of the trim panel to the top edge of the inner door panel, pressing down firmly until the trim panel is fully seated.… Read More

1998 Pontiac Grand Prix Fuel Pump Resistor Service Manual

Filed Under (Pontiac) by admin on 31-12-2013

Download Subject: 01033 — Fuel Pump Resistor Models: 1997-1998 Buick Regal GS & Pontiac Grand Prix GTP with L67 3.8L V6 Engine (Located in the High Corrosion Provinces of Newfoundland, Nova Scotia, Prince Edward Island, New Brunswick, Quebec and Ontario) Condition General Motors has decided that all 1997-1998 Buick Regal GS and Pontiac Grand Prix GTP model vehicles equipped with L67 3.8L V6 engines, located in the high corrosion provinces of Newfoundland, Nova Scotia, Prince Edward Island, New Brunswick, Quebec and Ontario, may develop an electrical open in the fuel pump resistor. This condition prevents operation of the fuel pump and the engine will not run. Correction Dealers are to install a new resistor on the plenum with an aesthetic cover. Vehicles Involved Involved are all 1997-1998 Buick Regal GS and Pontiac Grand Prix GTP model vehicles equipped with L67 3.8L V6 engines and built within these VIN breakpoints: Year Division Model Plant From Through 1997 Buick W Oshawa 2 V1400025 V1482781 1998 Buick W Oshawa 2 W1400008 W1614345 1997 Pontiac W Fairfax VF200090 VF359094 1998 Pontiac W Fairfax WF200104 WF342330 Important: Dealers should confirm vehicle eligibility through GM Access Screen prior to beginning campaign repairs.… Read More

1998 – 2000 Accord V6 2001 Accord V6 4-door from VIN 1HGCG1 Repair Instructions

Filed Under (Honda) by admin on 16-12-2013

Download REPAIR PROCEDURE 1. Remove the throttle body cover, intake manifold covers, ignition wire holder, and ignition wire cover. 2. Disconnect the brake booster vacuum hose and the vacuum hose from the intake manifold. 3. Remove the throttle body from the intake manifold (two nuts and two bolts). Leave all hoses, cables, and electrical connectors connected to the throttle body. Discard the throttle body gasket. 4. Remove the PCV valve from the cylinder head cover. Remove the intake manifold (three nuts and six bolts). 5. Remove the intake manifold chamber, IAT sensor, boost plate, and PCV hose from the intake manifold. 6. Cover the six ports on the bottom of the manifold with duct tape. 7. Use an 8-mm drill bit and carburetor cleaner to clean the EGR port in the intake manifold. Turn the drill bit only by hand. Do not use a power drill. 8. Put the special drill bit from the EGR pipe installation kit in your power drill.… Read More

2001-2005 HONDA CIVIC Vertical Doors Kit Installation Instructions

Filed Under (Honda) by admin on 09-03-2014

Download TOOLS REQUIRED FOR INSTALLATION: æ Spacers æ Blue painters tape æ Locktite red æ Screw Drivers Fork and Phillips æ Cutters æ 7mm,10mm, 13mm socket and extension æ Air ratchet, grinder and cutter æ 1/4, and 3/16 Allen wrench. (Note: The pictures on the manual are for reference only they may not match your vehicle.) 1) Disconnect the battery. 2) Remove fender: Remove all Phillip’s screws from the wheel well. Remove (1) 12mm bolt to loosen the bumper. Once the 12mm bolt has been removed pull on the bumper and remove (2) 8mm bolts from behind the bumper. Remove (3) 8mm bolts form the top of the fender. Remove (2) 8mm bolts from the bottom of the fender by the door. Remove (1) 8mm bolt holding the fender. At this point you should be able to remove the fender. 3) Remove the door catch: Open the door and remove (1) 10mm bolt from the body and (2) 10mm from the door.… Read More

You might also likeclose