how to fix blend door actuator motor 1999 toyota camry

You search Auto repair manual PDF about how to fix blend door actuator motor 1999 toyota camry, search results will appear below. If search results do not exist, please search by others keyword.

1999 Chrysler Truck Blend Door Actuator Replacement

Filed Under (Chrysler) by admin on 12-03-2014

  Download 1999 Chrysler Truck Blend Door Actuator Replacement

Download 1999 Chrysler Truck Town & Country LWB FWD V6-3.8L VIN L Vehicle Level Heating and Air Conditioning Air Door Air Door Actuator / Motor Service and Repair Blend Door Actuator Replacement. REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes.… Read More

  Download 1999 Chrysler Truck Blend Door Actuator Replacement

2005 HONDA CR-V DOOR VISORS INSTALLATION INSTRUCTIONS

Filed Under (Honda) by admin on 24-12-2013

  Download 2005 HONDA CR-V DOOR VISORS INSTALLATION INSTRUCTIONS

Download
PARTS LIST Left front door visor Right front door visor Left rear door visor Right rear door visor Installing the Front Door Visor 1. Lower the front door glass completely. Remove the door glass run channel from the door sash in the area shown. Do not remove the glass run channel from the door mirror base or the rear end of the door. AII 27171 TOOLS REQUIRED Isopropyl alcohol Shop towel Masking tape INSTALLATION NOTE: •These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors. Be careful not to damage the paint finish or glass run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours.… Read More

  Download 2005 HONDA CR-V DOOR VISORS INSTALLATION INSTRUCTIONS

Clunk, Bump or Squawk when Vehicle Comes to Complete Stop

Filed Under (Other Manuals) by admin on 02-04-2014

  Download Clunk, Bump or Squawk when Vehicle Comes to Complete Stop

Download 1999-2000 Cadillac Escalade (Old Style) 2002-2004 Cadillac Escalade, Escalade EXT 2003-2004 Cadillac Escalade ESV 1996-1999 Chevrolet 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 Chevrolet 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 Chevrolet Silverado Extended Cab Short Box (New Style) 1999-2004 Chevrolet Silverado 1500 Series Regular Cab (New Style) 2000-2004 Chevrolet 1500 Series Avalanche, Suburban and Tahoe 2001-2004 Chevrolet Silverado 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 Chevrolet Silverado 2500 Series Crew Cab, Short Box (New Style) 1996-1999 GMC 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 GMC 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 GMC Sierra Extended Cab Short Box (New Style) 1999-2004 GMC Sierra 1500 Series Regular Cab (New Style) 2000-2004 GMC 1500 Series Yukon, Yukon XL 2001-2004 GMC Sierra 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 GMC Sierra 2500 Series Crew Cab, Short Box (New Style) 2003-2005 HUMMER H2 with Four Wheel Drive (4WD) or All Wheel Drive (AWD) and One-Piece Propeller Shaft ONLY.… Read More

  Download Clunk, Bump or Squawk when Vehicle Comes to Complete Stop

2001-2006 Toyota Sequoia BACK DOOR POWER WINDOW INOPERATIVE

Filed Under (Toyota) by admin on 10-12-2013

  Download 2001-2006 Toyota Sequoia BACK DOOR POWER WINDOW INOPERATIVE

Download 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9.… Read More

  Download 2001-2006 Toyota Sequoia BACK DOOR POWER WINDOW INOPERATIVE

2002 Chrysler Voyager LX ACCESSORIES and EQUIPMENT Power Windows

Filed Under (Chrysler) by admin on 19-01-2014

  Download 2002 Chrysler Voyager LX ACCESSORIES and EQUIPMENT Power Windows

Download TROUBLE SHOOTING Inspect power window circuit breaker (25-amp), located in left kick panel. Inspect fuse No. 28 (40-amp) in Intelligent Power Module (IPM). IPM is located on left side of engine compartment. Inspect ground at right “B” pillar. SYSTEM TESTS ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay.… Read More

  Download 2002 Chrysler Voyager LX ACCESSORIES and EQUIPMENT Power Windows

1994 Toyota Camry DX TIMING BELT REMOVAL and INSTALLATION

Filed Under (Toyota) by admin on 01-01-2014

  Download 1994 Toyota Camry DX TIMING BELT REMOVAL and INSTALLATION

Download 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of way. On Camry, remove coolant reservoir tank if it interferes with timing belt removal. Remove engine control (torque) rod from front of engine. 3. On all models, remove accessory drive belts. Using floor jack, slightly raise engine to remove weight from right (timing belt side) engine mount at timing belt cover. 4. Remove right (timing belt side) engine mount and bracket from front of engine. Remove spark plugs. Remove No. 2 timing belt cover and gaskets. See Fig. 1 . 5. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No.… Read More

  Download 1994 Toyota Camry DX TIMING BELT REMOVAL and INSTALLATION

Ford Focus Lambo Style Doors Installation Instructions

Filed Under (Ford) by admin on 30-01-2014

  Download Ford Focus Lambo Style Doors Installation Instructions

Download Preparations: (Dismantling according to the regulation of the car manufacturer) – Disconnect the battery. – Remove the front bumper – Remove the front fender – Disconnect the cables (cable tree bodywork / door) – Loose the hinge at the A-pillar – Dismantle the door hinges from the door. – Extend the door cable tree with the. ( see enclosure “cable extension” ) (see enclosure “modification of the fender”) Tip/Advise: a second person makes ) Reference: On the driver’s side additionally the splash-water container must be removed and be installed in another place at the vehicle again. (assembly suggestion on the last sides) Installation LSD-Door Mounting/Hinge: 1.) Dismantle the swing arm off the chassis plate 2.) Mount the LSD chassis plate at the fitting points at the original door hinges at the bodywork. Please use screws (A) and fix it in the middle of the hole. Please exchange additionally the cable plug-in connector with the dummy plug (as shown on picture under point 13) 3.) Screw on the LSD swing arm onto the former original fitting points of the hinge at the already dismantled door.… Read More

  Download Ford Focus Lambo Style Doors Installation Instructions

8005 & 8005TK FORD 1999 to current Super Duty F250, F350, F450, F550 and Excursion with stock manual mirrors Installation Instructions

Filed Under (Ford) by admin on 25-12-2013

  Download 8005 & 8005TK FORD 1999 to current Super Duty F250, F350, F450, F550 and Excursion with stock manual mirrors Installation Instructions

Download Do not attempt to manually extend or retract the mirrors. They should be moved under their motor power only!! Tools required for the installation are: 7/16″, 5 mm & 9/32″ sockets, a small screw driver, electrical tape and a sharp tool for cutting a hole for the in/out switch. Model 8005TK will also require a volt meter. If you have any questions after reading this installation manual, please call our service department at (800) 337-2557 REMOVAL OF EXISTING MIRROR: 1. Remove the trim panel on both doors (note – Ford doors do not have retaining clips located around the doors as other models have). To remove the trim panels, start by removing the trim panel on the front side of the window. Remove the plastic panel that holds the electric windows and door locks (to remove this panel pry up from the front or tip of the panel). After you have removed the plastic panel unscrew the 9/32″ screw seen in the back of the hole.… Read More

  Download 8005 & 8005TK FORD 1999 to current Super Duty F250, F350, F450, F550 and Excursion with stock manual mirrors Installation Instructions

2001 Mazda Truck MPV DX FRONT DOOR DISASSEMBLY/ASSEMBLY

Filed Under (Mazda) by admin on 31-12-2013

  Download 2001 Mazda Truck MPV DX FRONT DOOR DISASSEMBLY/ASSEMBLY

Download 1. Lower or raise the front door glass so that the distance from the top of the front door glass at the rear end to the upper part of the front molding is 185 mm {7.3 in} 2. Disconnect the negative battery cable. 3. Remove the front door trim.4. Disassemble in the order indicated below. 1. Inner handle 2. Front door trim bracket 3. Door screen 4. Front door glass 5. Front manual window regulator 6. Front power window regulator 7. Glass run channel 8. Front door lock 9. Outer handle 10. Door key cylinder 11. Door weatherstrip 12. Door lower weatherstrip 5. Assemble in the reverse order of disassembly. Front Door Glass Disassembly Note 1. Remove the front door glass installation bolts. 2. Slant the front door glass as shown, and remove the front door glass from the inside of the front door. Outer Handle Assembly Note 1. Connect the door key cylinder harness of outer handle as shown.… Read More

  Download 2001 Mazda Truck MPV DX FRONT DOOR DISASSEMBLY/ASSEMBLY

Acura 2.3CL and 3.0CL Security System Installation Notes

Filed Under (Acura) by admin on 31-01-2014

  Download Acura 2.3CL and 3.0CL Security System Installation Notes

Download Locate the Keyless Security Control unit underneath the passenger seat and refer to the 2 connector illustrations below to make your connection. Connector A: A1: Ignition A2: Interior light (Supervision) A3: Door Actuator (Motor) A4: Trunk Actuator (|Motor) A5: Door Actuator (Motor) A6: Starter Cut Relay A7: Security Indicator A8: Siren Out (-) A9: Door Actuator (Motor) A10: Ground A11: Light Flash Out (+) (Parking) A12: Battery 12v+ Input Connector B: B1: Hood switch B7: Lock &(Alarm Arm) Pass sideB13: Not used B2: Unlock Input (-) B8: Lock &(Alarm Arm) Driver sideB14: Not Used B3: Unlock Input (-) B9: Trunk Latch Input (-) B15: Not Used B4: Not Used B10 Key In Ignition (Neg input) B16: Light Flash Out (+) Head. B5: Unlock Input (-) B11: Lock Input (-) B17: Unlock Input & (Alarm dis.) B6: Lock Input (-) B12: Door Ind (Instrument cluster) B18: Start Input (12v in Crank)… Read More

  Download Acura 2.3CL and 3.0CL Security System Installation Notes

You might also likeclose