Audi TT Glove Box Repair

Download Audi TT Glove Box Repair Broken latches, not staying shut, or not opening. The TT glove box has a few issues that are annoying and costly at the dealership. This guide can solve the problems with a short bit of your time, and about $10. Latch Repair To repair your glove box latch all you may need is one set screw from a hardware store, and a matching thread tap. For about $.30 you can buy a stainless steel 8-32 x 5/16″ set screw. If the pins that keep your glove box shut do not spring back out on their own, you may need a couple pieces of special hardware. I used radio control car parts available from most hobby stores. You will need a pack of 4-40 x 3/8″ socket head cap screws that have a hole drilled in them (Team Associated part #6929) and lock nuts (Team Associated part #4449).… Read More

POLLEN FILTER INSTALLATION GUIDELINES

Download
Introduction If there is an absence of a specific researched detail instruction for your model of car then this guide should help you to find and change the cabin air filter in your car. If even with this guideline you encounter difficulty, you could try referring to a maintenance manual for the model of car or looking on the Internet for owners clubs and chat rooms etc., which can often provide help. In the vast majority of cases the filter is easy to fit and will often take no more than 10-15 minutes. Some can be done in a matter of seconds and don’t even need any tools. Tools With the following tools you should have no problem upgrading your filter to a Puravent filter. • Screwdriver with a set of interchangeable screwbits, including flat, pozidrive and torx bits. • Pointed nose pliers • Adjustable spanner (or small socket set is even better) Find the old filter In most cases, particularly on older European cars, the filter will be located in the area at the top of the bulkhead that separates the engine bay from the passenger compartment.… Read More

Clunk, Bump or Squawk when Vehicle Comes to Complete Stop

Download 1999-2000 Cadillac Escalade (Old Style) 2002-2004 Cadillac Escalade, Escalade EXT 2003-2004 Cadillac Escalade ESV 1996-1999 Chevrolet 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 Chevrolet 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 Chevrolet Silverado Extended Cab Short Box (New Style) 1999-2004 Chevrolet Silverado 1500 Series Regular Cab (New Style) 2000-2004 Chevrolet 1500 Series Avalanche, Suburban and Tahoe 2001-2004 Chevrolet Silverado 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 Chevrolet Silverado 2500 Series Crew Cab, Short Box (New Style) 1996-1999 GMC 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 GMC 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 GMC Sierra Extended Cab Short Box (New Style) 1999-2004 GMC Sierra 1500 Series Regular Cab (New Style) 2000-2004 GMC 1500 Series Yukon, Yukon XL 2001-2004 GMC Sierra 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 GMC Sierra 2500 Series Crew Cab, Short Box (New Style) 2003-2005 HUMMER H2 with Four Wheel Drive (4WD) or All Wheel Drive (AWD) and One-Piece Propeller Shaft ONLY.… Read More

Peugeot 106 Dog Engagement Gear-Box Mounting Instructions

Download
Changes to be made to the original parts in order to have a correct mounting of the Bacci-production gear-box. 1. Installation of the supplied lock plate for the two ball bearings. In the kit we supply n° 4 hexagonal head bolts, n° 2 bearing locking rings (Seeger- type) and a lock plate (see photo n°1). The kit has to be applied to the central box of the gear group (photo n°2) and it modifies the production model bearing locking system. The 4 bolts and the 2 rings replace the original parts. Mount the Bacci gear-box and lock the two ball bearings with the supplied Seeger- type rings. After that, lock the two bearings with the plate and the bolts you found in the kit (photo n°3). Be careful to screw the 4 bolts at 3 kgm with a dynamometric wrench and to lock them with Loctite. 2. Application of the support (supplied with the kit) to the central box.… Read More

2009 Honda Odyssey Roof Box, Short Installation Manual

Download
PARTS LIST Roof box 4 Brackets A 4 Brackets B 4 Plates 8 Knobs 8 Bolts 8 Washers 2 Straps Seal 2 Keys 4 Large pads 4 Small pads SUPPLIES REQUIRED Isopropyl alcohol Shop towel.
INSTALLATION NOTE: •Be careful not to damage the roof and other finished surfaces of the body when installing the roof box. •The maximum load capacity for this product is 110 lb (50 kg); approximate product weight is 29 lb (13 kg). •Do not allow the combined weight of the accessory and cargo to exceed the carrying capacity of the roof rack. •Honda roof racks or crossbars are required to install the roof box. 1. Open the roof box. Attach an adhesive seal over each of the unused mounting holes along the bottom of the box. The seals will help prevent water from entering the roof box. 2. Using isopropyl alcohol on a shop towel, clean four brackets B where the small pads will attach.… Read More

1997-2003 Ford F150 SuperRail Mounting Kit #3342

Download
Installation Instructions SPECIFICATIONS ?? Fits 1997-2003 Ford F-150 (not Supercrew) KING PIN TRAILER PLATE INSTALLATION FOR KING PIN BOXES WITH A FLANGE : Figure3. 1. Place the Trailer Plate {J2} over the King Pin, with the guide wedge towards the rear of the trailer (wedge facing down). Align the Trailer Plate {J2} square with the king pin box and clamp in place to prevent movement. 2. Mark the holes for drilling through the Trailer Plate {J2} onto the King Pin Box flange. 3. Remove the Trailer Plate {J2} or use it as a guide and drill ¼ ” holes through the flange. 4. Re-install the Adapter Plate (as in step 1). 5. Use the ¼” bolts provided, to secure the Trailer Plate {J2} onto the king pin box flange. A minimum of 10 bolts must be used to fasten the plate on. For use with heavy trailers, more bolts will be needed to secure this plate.… Read More

2007 Honda Odyssey MusicLink For i-Pod Installation Manual

Download
TOOL AND SUPPLIES REQUIRED #2 Phillips screwdriver Flat-tip screwdriver Diagonal cutters Scissors Ratchet 10 mm Socket 10 mm Combination wrenches Drill motor Drill bit (3 mm) 19 mm Hole saw (3/4″) Electrical tape Felt-tip pen Pushpin Eye protection Isopropyl alcohol.
INSTALLATION 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. If the your vehicle is equipped with a navigation system, go to step 22 ; if not, continue with step 3. 3. Place the shift lever in the N (Neutral) position. 4. Remove the center panel (ten clips and disconnect the connectors). 5. Remove the audio unit (three self-tapping screws, two clips, and disconnect the vehicle connector). 6. Remove the damper arm cover and disconnect the arm. 7. Open the glove box and remove the two stoppers by releasing the two retaining tabs.… Read More

1993-1999 Peugeot 306 Part 57-0509 Installation Guide

Download Parts list: 1 x Air filter Element 1 x Cold Air Hose Assembly 1 x Literature Pack Fixing kit: – 1 x #48 Hose Clamp 4 x Plastic Ties. INSTALLATION INSTRUCTIONS 1. Disconnect the negative battery terminal from the battery. 2. Unclip, unbolt and remove the air box intake pipe from the vehicle. (Fig. 1) 3. Unclip, unbolt and remove the air box to engine intake pipe from the vehicle. (Fig. 2&3) 4. Remove the rubber seal from the air box neck. (Fig. 4) 5. Using a junior hacksaw cut 4 x 1mm wide slits equally spaced around the air box neck. Remove any loose plastic from the air box (Fig. 5) 6. Unclip the base from the airbox and remove the original filter element. (Fig. 6) 7. Using a hot air gun gently warm the air box neck to aid fitting of the Air filter assembly. 8. Feed the Air filter assembly into the air box and through the air box neck.… Read More

Audi A8 Parrot 3100 Bluetooth Kit Installation Instructions

Download Installing a Parrot 3100 Bluetooth Kit in a D3 Audi A8. This procedure is to be used in conjunction with the audipages.com checklist, wiring diagram and wiring table supplied with your kit. Remove Fuse SB13 Remove the left hand side fuse panel. This is accomplished by popping the cover off with a trim stick. Once complete, REMOVE fuse SB13 (the fuse labled 13) , which is the unswitched power to the Telematics/telephone box before starting. This will prevent inadvertent grounding of the power supply during installation. Remove Trim and Telematics Box Remove the door kick panel trim by prying it up on the aft portion of it and unclipping it, then pull the vertical portion out, it just clips out. Remove the driver’s side floor mat. Using a Torx T-35 screwdriver, remove the screw that holds the left foot rest in place. Be careful when removing the screw not to drop it down into the floor board.… Read More

2004 Honda CR-V Accessories Subwoofer Kit Installation Guide

Download
TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver Flat-tip screwdriver Stubby Phillips screwdriver Utility knife Scissors Tape measure Isopropyl alcohol (Isopropyl alcohol, in a 60/40 solution with water) Ratchet 10 mm Socket 14 mm Combination wrench Shop towel 13/16″ (20 mm) Hole saw Center punch Eye protection (face shield, safety goggles, etc.)
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 3. Remove the two screws that fasten the bottom of the center panel. 4. Pull the center panel out toward you to release the six clips, unplug the vehicle connector from the hazard switch, and remove the center panel.… Read More