Download When performing service around Supplemental Inflatable Restraint (SIR) system components or wiring, the SIR system must be disabled. Failure to do so could result in possible air bag deployment, personal injury, or unneeded SIR system repairs. Catera Disconnect the negative battery cable. 1. Remove the steering wheel. 2. Remove the inflatable restraint steering wheel module coil. 3. Insert a small pointed awl or wire into the ignition lock cylinder release pinhole. 4. Pull out the ignition lock cylinder. 5.Fig. Insert a pointed tool into the release pin hole To install: Install the lock cylinder. Look into the hole that receives the lock cylinder on the lower RH side in order to locate the locking lever. 1. Carefully push down on the locking lever using a small flat-bladed tool until an audible click is heard. 2. Place the lock cylinder into the empty hole. 3. 6. Install the inflatable restraint steering wheel module coil.… Read More
Download Subject: Procedure to Disable Illumination of Service Indicator AFTER the Installation of Passive Struts/Shocks Models: 1992-94 Buick Skylark 1993-96 Buick Park Avenue 1989-92 Cadillac Allante 1991-93 Cadillac Eldorado, Seville 1991-95 Cadillac DeVille 1991-95 Oldsmobile Ninety Eight 1992-93 Oldsmobile Achieva 1994-99 Pontiac Bonneville This bulletin is being revised to clarify when this bulletin may be used to turn the service suspension lamp off. Also, a step has been added to the 1991 Cadillac Eldorado and Seville repair. Please discard Corporate Bulletin Number 00-03-11-001 (Section 3 – Suspension). Refer to the Service Manual page 8D-13 (1989) or 8D-14 (1990-1992). On these vehicles, adjust the BCM Override value “BS08″. To do this, use the warmer/cooler button on the CCDIC to decrease the BCM override value “BS08″ which is displayed when you enter the system by two (2). When the desired number is displayed on the CCDIC, it must be stored by holding the “Elapsed Time” and “Fuel Used” buttons until the new value flashes on and off.… Read More
Download 2000 Cadillac Catera V6-3.0L VIN R Timing Belt: Service and Repair Timing Belt Replacement. Removal Procedure ^ Tools Required -J 42069 Timing Belt Alignment Kit -J 42098 Crank Hub Torx Socket Notice: Failure to follow the described timing belt inspection and maintenance may result in a broken timing belt and cause severe engine damage. 1.Inspect the cold start counter (also called a heavy duty register) with a scan tool. If there are any cold starts (below -28° C or -20° F) visually inspect the timing belt for cracks. It cracks are noted, do not reuse the belt. Replace the belt and clear the cold start counter. If the belt is okay, and is reused, do not clear the cold start counter. 2.Remove the intake air resonator. Refer to Intake Air Resonator Replacement in Powertrain Management. 3.Remove the intake plenum. Refer to Intake Plenum Replacement. 4.Remove the timing belt cover. Refer to Timing Belt Cover Replacement.… Read More
Download PRE-INSTALLATION NOTES TONNEAU INSTALLATION GUIDE INSTALLATION KIT CHECKLIST A B C D G H I E F A: Hydraulic Struts B: Stainless Steel Bolts 5/16″ x 1 1/4″ C: J-Hooks & Wall Mounting Screws D: Clamps E: Spiral Rings F: Stainless Steel Washers 5/16″ G: Stainless Steel Lock Washers 5/16″ H: Forward Mounting Brackets I: Rear Mounting Brackets Page 1 Model 2010 Ford F150 Heritage Style Short Bed 1997 – 2004 Page 1 FORM # IG2010 Modified May 2008 Be sure to use only cleaners, waxes, etc., which are labeled ‘Safe for Plastics’. Make sure that chemicals or substances, which are not labeled ‘safe for plastics’, do not come in contact with your Undercover. Failure to do so could cause discoloration and/or structural damage to your Undercover and will void your warranty. Paint rubbing of the truck is normally not a problem, but is always a possibility with any tonneau.… Read More
Download Removal Procedure 1. Disable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR. 2. Remove the upper and lower trim covers. Refer to Steering Column Trim Covers Replacement . 3. Remove the wire harness assembly (1) from the wire harness strap (2). 4. Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector. Fig. 29: Turn Signal & Multifunction Switch Assembly Connectors Courtesy of GENERAL MOTORS CORP. 5. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly out of the bulkhead connector (1). 6. Remove the 2 pan head tapping screws (1) and (3) from the turn signal and multifunction switch assembly (2). 7. Remove the turn signal and multifunction switch assembly (2) from the steering column tilt head assembly. Installation Procedure 1. Install the turn signal and multifunction switch assembly (2) onto the steering column tilt head assembly.… Read More
Download Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada.… Read More
Download SYMPTOM A screech or whine from the rear differential when making a tight turn at low speed (for example, in a parking lot when 4WD engages). PROBABLE CAUSE The differential fluid is contaminated or broken down, providing insufficient lubrication. CORRECTIVE ACTION Replace the dual pump fluid, and test-drive the vehicle. If necessary, replace the rear differential clutch, replace the oil pump assembly (1997 model only), and add a flow collar. PARTS INFORMATION Flow Collar Kit: P/N 41431-P6R-000, H/C 6839724 Differential Clutch Set: P/N 48010-P6R-305, H/C 6627566 Oil Pump Set (1997 model only): P/N 48100-P1D-305, H/C 6839716 REQUIRED MATERIALS Dual Pump Fluid: P/N 08200-9002, H/C 6512644 Liquid Gasket (Hondabond HT): P/N 08718-0001, H/C 2963817. REPAIR PROCEDURE 1. Drain and refill the rear differential with Dual Pump Fluid. 2. Check the tires for proper inflation (recommended cold inflation front and rear is 26 psi) and any variation in tire size or type.… Read More
Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More
Download BUICK Century 1997-99 LeSabre 1995-99 1 Park Avenue 1995-99 Regal 1995-99 Riviera 1996-99 Roadmaster 1995-96 Skylark 1996-98 CHEVROLET Impala 2000 Venture 2000 OLDSMOBILE Achieva 1996-98 Aurora 1995-99 Bravada 1998-99 Cutlass 1998-99 Cutlass Supreme 1995-97 Eighty-Eight 1994-99 Intrigue 1998-99 LSS 1996-99 Ninety-Eight 1994-96 Regency 1997-98 Silhouette 2000 PONTIAC Montana 2000 Sunfire 2000. BUICK LeSabre / Park Avenue 1995-99 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the plastic trim piece to the left of the glove box and (1) Phillips screw exposed. Unsnap the top edge of the knee bolster panel. Remove (1) Phillips screw from the panel. Remove the ashtray cluster and (2) Phillips screws from each side. Unclip the entire dash trim bezel and remove. Remove (3) 9/32″ hex-head screws securing the factory head unit and disconnect the wiring. Skip to the Installation Instructions for ALL VEHICLES on Page #6. CHEVROLET Impala 2000 Disconnect the negative battery terminal to prevent an accidental short circuit.… Read More
INSTALLATION MANUAL Gas Downloader Vehicle Application Power Pup Part# ’04-’06 Ford F-150 41590 ’03-’06 Dodge Ram 5.7L Hemi 42590 ’98-’06 GM full sized pickup/SUV 43590.
TABLE OF CONTENTS Introduction ….page. 2 Bill of Materials ….. page. 2 Operating Instructions … page. 3 Installation …. pages. 4
-11 Main Menu Options …. pg. 4 Install Download …. 4 Read DTC’s (Diagnostic Trouble Codes) …. 4 Ford F-150 installation …. page. 5-6 GM pickup and SUV installation ….. page. 7-9 Dodge Ram 5.7L Hemi installation ….. page. 10-11 Facto RY Settings ….. page. 12 Internet Upgrades….. page. 12 Faq/troubleshooting …. page. 13 warrantY & Disclaimer ….. page. 13.
Download for full instructions… Read More