how to change remote oil line on blazer

You search Auto repair manual PDF about how to change remote oil line on blazer, search results will appear below. If search results do not exist, please search by others keyword.

1998 Chevrolet Blazer Engine Oil Cooler Hose/Pipe Replacement

Filed Under (Chevrolet (Chevy)) by admin on 12-03-2014

Download 1998 Chevrolet Blazer – 4WD | Blazer, Bravada, Jimmy, S10 Pickup,  Sonoma (VIN S/T) Service Manual | Engine | Engine Mechanical – 4.3L | Repair Instructions. Engine Oil Cooler Hose/Pipe Replacement (4WD) Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6.… Read More

Honda Silver Wing Oil/Filter Change Instructions

Filed Under (Honda) by admin on 09-12-2013

Download Time and Ease: Easy­ 30 minutes Tools/Supplies: Wrench, oil, oil pan, rags, funnel, maybe an O­ring Step 1 ­Park the scooter on its center stand on a firm, level surface. If the engine is cold, start it and let it idle for 3­5 minutes. Turn the engine off. Wait 2­3 minutes for the oil to settle. Step 2 ­Place a drain pan under the oil plug (below right side fairing) . To drain the oil, remove the oil filler cap/dipstick, oil plug , spring, and oil strainer screen. Step 3 ­Remove the oil filter with a filter wrench and let the remaining oil drain out. Discard the oil filter in an approved manner. Step 4 ­Install the oil filler cap/dipstick securely. Pour the drained oil into a suitable container and dispose of it in an approved manner. Step 5 ­Apply a thin coat of engine oil to the rubber seal of a new oil filter.… Read More

Checking oil level in automatic transmission and adding oil

Filed Under (Other Manuals) by admin on 28-03-2014

Download TRANSMISSION 722.700 in MODEL 168.031 /032 /033 /131 /132 /133 TRANSMISSION 722.701 in MODEL 168.006 /007 /008 /009 /109 TRANSMISSION 722.702 in MODEL 168.035 /135 TRANSMISSION 722.750 /751 in MODEL 414.700. Adding transmission oil Risk of accident. Secure vehicle to prevent it from moving. AS00.00-Z-0005-01A Danger! Accidents may result if the vehicle starts off unintentionally with the Wear closed and snug-fitting work clothes. engine running. Risk of injury. Do not grasp hot or rotating parts. Crushing and burn injuries may result while working on engine during when it is being started or when it is in operation. 1 Remove locking pin (1) To do this, break off the plate on the locking pin using a suitable tool and press out the remaining pin in the cap downwards 2 Remove cap (2) 3 Fill with transmission oil The vehicle must be horizontal. Transmission oil (ATF) in accordance with BB00.40-P-0236-10A Specifications for Operating Fluids, sheet no.… Read More

RCR311W Universal Remote Control Owner’s Manual

Filed Under (Other Manuals) by admin on 16-01-2014

Download Three-Component Universal Remote Congratulations on your purchase of this three-component universal remote. This universal remote controls up to three electronic components and makes juggling remote controls a thing of the past. Your remote is guaranteed to work with all brands of components. The three-component universal remote is easy to use, easy to program and gives you control at the touch of your fingertips. SAVE THIS MANUAL AND THE CODE LISTS! Remote controls can sometimes lose their programming when you change the batteries. Make sure you keep the manual and code lists in a safe place so that you can reprogram the remote if you need to. Battery Installation and Information Your universal remote requires two AA Alkaline batteries (batteries may or may not be included, depending on model). To install the batteries: 1. Remove the battery compartment cover. 2. Insert the batteries, matching the batteries to the (+) and (-) marks inside the battery compartment.… Read More

1994 AUDI UrS4 Stainless Steel Brake Flex Line Installation

Filed Under (Audi) by admin on 05-04-2014

Download Rear Line Installation I started with the right rear line since this is first in the bleeding sequence. The rear line (see Photo 1) has one threaded female flare fitting (connects to steel brake line) and one threaded male fitting (connects to the caliper). Break both fittings loose on the line on the car. Also break loose the bleeder screw on the caliper before proceeding to avoid the embarrassment of getting the new line on and not being able to bleed it. The caliper connection should come loose easily but the connection to the steel line may give some trouble on rust belt cars. Use your favorite penetrating oil on both. I had to use the flame wrench on one of my connections. Front Line Installation The front flex lines have threaded female flare connections at both ends that connect to steel brakes lines – one from the master cylinder and the other from the caliper.… Read More

2000 Buick Regal Oil Pan Replacement

Filed Under (Buick) by admin on 02-01-2014

Download Tools Required z J 28467-90A Engine Support Adapters z J 28467-B Universal Engine Support Fixture z J 36462-A Engine Support Adapter Leg Set 1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical. 2. Carefully disconnect the throttle body air inlet duct. 3. Remove the engine mount struts from the engine. Refer to Engine Mount Strut Replacement . 4. Remove the drive belt. Refer to Drive Belt Replacement . 5. Install the J 28467-90A , the J 28467-B and the J 36462-A . Do not raise the engine. Refer to Engine Support Fixture . 6. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 7. Disconnect the three-way catalytic converter pipe from the right exhaust manifold. Refer to Catalytic Converter Replacement in Engine Exhaust. 8. Remove the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.… Read More

Honda/Acura Oil Pan and Oil Pump Pickup Installation Instructions

Filed Under (Honda) by admin on 20-12-2013

Download NOTE: These instructions aehicle. Use approved jack standre a basic guideline and some descriptions may not apply to all vehicles. Always consult the proper service manual for complete instructions. 1. Make sure vehicle is in Park and on a level surface, emergency brake on, chock wheels and jack up vs for safety. Or place car on a lift. 2. Drain oil from pan and disconnect the oxygen sensor from the lower exhaust if equipped. Remove the lower splash shield, lower exhaust and hanger, and transaxle brackets and dustcover. Remove oil pan from engine. 3. Remove the factory oil Pump pickup. Save the mounting hardware and clean thoroughly. Also at this time scrape any old gasket material from engine block and oil pump flange. 4. Install the new Moroso Oil Pump Pickup, P/N 24010 (VTEC) or P/N 24011 (non-VTEC), with a the new oil pump pickup gasket (supplied with oil pump pickup).… Read More

2007 Honda Accord CR-V and Civic Remote Engine Starter FAQ

Filed Under (Honda) by admin on 02-01-2014

Download
Model Information Release date for Accord Remote Starter System: September 20, 2007 Release date for CR-V and Civic Remote Starter System: End of September 2007 Technical Questions Q: What does the Honda Remote Engine Starter System do? A: The Honda Remote Engine Starter is a two-way remote system that starts and stops your vehicle’s engine anywhere within a 200-foot range. It’s designed to warm up your vehicle in the winter and cool it down in the summer. Q: How much is the Honda Remote Engine Starter? A: Approximately $499.00 without installation for all applicable Honda models. Check with your Honda dealer for the installation cost. Q: Can I install it myself? A: AHM does not recommend that customers install the Honda Remote Engine Starter due to the complexity of its electrical components. Authorized Honda Technicians are professionally trained to safely install the Remote Engine Starter. Q: Can I have my neighborhood audio shop install the Honda Remote Engine Starter?… Read More

Ford Super Duty 4×4 Mag Hytec Rear Diff Cover Install and Rear Diff Gear Oil Change 2004 F250 4×4 XLT Sport Crew Cab

Filed Under (Ford) by admin on 17-02-2014

Download TOOLS & PARTS I USED – Mag-Hytec Ford 10.5 rear differential cover – Redline #57914 75W140 gear oil, 6 quarts – 1/2″ socket & ratchet (cover bolt removal) – Flat screwdriver – Torque wrench – Drain pan – Several rags – Plastic putty paddle – Small funnel – Lacquer thinner – 1/4″ allen wrench (new cover bolt install) PROCEDURE Here’s a few pics of the Mag Hytec cover. Its a very impressive cover, complete with additional oil capacity, a magnetic dipstick, a drain plug, a 1/8 NPT port (for a temperature sending unit), and an o-ring to seal to the rear diff case. Here’s a shot of the dipstick (left) and temperature sender port. Here’s a pic of the drain plug on the bottom. Dipstick removed
Drain plug removed Here’s the stainless hardware that’s included with the cover. They also include the two sizes of allen wrenches needed for the installation of the bolts and to service the drain plug/diptstick/sender port.… Read More

1100F FORD PATS / SECURILOCK REMOTE START INTERFACE-DATA

Filed Under (Ford) by admin on 31-12-2013

Download PRODUCT ACCESSORIES DESCRIPTION The 1100F interface module is used when installing remote start products in Ford vehicles equipped with a factory immobilizer. The 1100F allows for easy interfacing between the remote start and the factory immobilizer, while maintaining the integrity of the OEM system. The factory transponder-based anti-theft system uses a small electronic chip hidden in the key to send a code to the vehicle’s transceiver when the ignition is energized. The key must be placed in the ignition and turned to the RUN position. This energizes a coil surrounding the key, which in turn energizes the chip, which sends a code to the vehicle. If the vehicle does not detect the code being sent, the vehicle will start and then immediately shut off or will just crank, and the anti-theft light will flash. The 1100F provides a valid code to the vehicle whenever it is remote started, but does not affect the immobilizer system during normal vehicle operation; the immobilizer system remains fully functional.… Read More

You might also likeclose