how do you check automatic transmission fluid on a peugeot 407

You search Auto repair manual PDF about how do you check automatic transmission fluid on a peugeot 407, search results will appear below. If search results do not exist, please search by others keyword.

2002 Jaguar X-Type Transmission Fluid Level Check

Filed Under (Jaguar) by admin on 29-12-2013

  Download 2002 Jaguar X-Type Transmission Fluid Level Check

Download 2002 Jaguar X-Type V6-2.5L Vehicle Level Maintenance Fluids Fluid – A/T Testing and Inspection. Transmission Fluid Level Check Raise and support the vehicle. 1. Connect the approved Jaguar diagnostic system. 2. Make sure J-Gate shift selector is in the Park position (P). 3. With the engine running and the foot brake applied, move the J-Gate shift selector through “P-R-N-D-4-3-2″ and back to the “P” position to circulate the automatic transmission fluid until the temperature reaches 30 to 40°C (86 to 104°F) on the approved Jaguar diagnostic system. 4. When the automatic transmission fluid temperature reaches 35°C (95°F) check that the selector lever is in the “P. position raise the vehicle. Motor / ALLDATA Online – 2002 Jaguar X-Type V6-2.5L – Testing and… http://www.motoralldata.com/alldata/MOTOR~V71595976~C40438~… 2 of 4 3/28/2008 11:44 AM Zoom Sized for Print If the automatic transmission fluid does not come out of the transmission fluid level tube the automatic transmission fluid level is insufficient.… Read More

  Download 2002 Jaguar X-Type Transmission Fluid Level Check

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Filed Under (Other Manuals) by admin on 01-01-2014

  Download 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Download Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) #05-07-30-031: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) – (Nov 11, 2005) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case.… Read More

  Download 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

2001 Oldsmobile Alero V6-3.4L VIN E Service and Repair

Filed Under (Oldsmobile) by admin on 01-01-2014

  Download 2001 Oldsmobile Alero V6-3.4L VIN E Service and Repair

Download 2001 Oldsmobile Alero V6-3.4L VIN E Service and RepairThe fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid. Inspect The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F) . CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe. The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid. WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole.… Read More

  Download 2001 Oldsmobile Alero V6-3.4L VIN E Service and Repair

Checking oil level in automatic transmission and adding oil

Filed Under (Other Manuals) by admin on 28-03-2014

  Download Checking oil level in automatic transmission and adding oil

Download TRANSMISSION 722.700 in MODEL 168.031 /032 /033 /131 /132 /133 TRANSMISSION 722.701 in MODEL 168.006 /007 /008 /009 /109 TRANSMISSION 722.702 in MODEL 168.035 /135 TRANSMISSION 722.750 /751 in MODEL 414.700. Adding transmission oil Risk of accident. Secure vehicle to prevent it from moving. AS00.00-Z-0005-01A Danger! Accidents may result if the vehicle starts off unintentionally with the Wear closed and snug-fitting work clothes. engine running. Risk of injury. Do not grasp hot or rotating parts. Crushing and burn injuries may result while working on engine during when it is being started or when it is in operation. 1 Remove locking pin (1) To do this, break off the plate on the locking pin using a suitable tool and press out the remaining pin in the cap downwards 2 Remove cap (2) 3 Fill with transmission oil The vehicle must be horizontal. Transmission oil (ATF) in accordance with BB00.40-P-0236-10A Specifications for Operating Fluids, sheet no.… Read More

  Download Checking oil level in automatic transmission and adding oil

Ford BD Performance Transmission Installation Instructions

Filed Under (Ford) by admin on 14-01-2014

  Download Ford BD Performance Transmission Installation Instructions

Download
REMOVAL: 1) Disconnect the negative battery cable(s). 2) Place the transmission into the Neutral (N) position. 3) Raise the vehicle on a hoist. 4) Mark the drive shaft and pinion yokes for assembly alignment. On 4WD models, remove the skid plate. 5) Remove the transmission oil filter tube nut and filler tube. 6) Position a drain pan & disconnect the transmission fluid cooler tubes at the cooler bypass valve. 7) Remove the drive shaft. On 4WD models, remove the front drive shaft & transfer case assembly. On SuperDuty/Motorhome models, remove the transmission mounted parking brake assembly. 8) NOTE: If the vehicle is equipped with a PTO (Power Take-Off) unit, all or part of the PTO will need to be removed. 9) Disconnect the shift cable from the transmission and manual lever. 10) Disconnect the cable housing from the bracket. 11) Disconnect the digital transmission range (TR) sensor connector. 12) Remove the transmission heat shield.… Read More

  Download Ford BD Performance Transmission Installation Instructions

MONSTER TRANSMISSIONS : FORD TRANSMISSION INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 31-12-2013

  Download MONSTER TRANSMISSIONS : FORD TRANSMISSION INSTALLATION INSTRUCTIONS

Download
Please Note : The following instructions were made to act as a guide/reference, if you are inexperienced with performing an automatic transmission installation it is highly recommended that you contact a certified experienced professional to perform the installation and/or make the proper adjustments for you! Instructions : (1) Pre-installation instructions; Disconnect Battery terminal, inspect and check transmission coolant lines for damage, flush lines and coolant system thoroughly. (2) Inspect crank well for converter hub wear, and clean this area. (3) Check Flywheel for cracks and converter bolt holes for wear. (4) Inspect back of engine block where transmission mates, ensure block is clean, no wires or cables are in the way of installation. (5) Inspect and verify both dowel pins are clean and secure in block. (6) Ensure Block Plate is aligned and straight. (7) Clean area of block so transmission can make a good ground. “Warning” Transmission will suffer permanent damage if grounded improperly!… Read More

  Download MONSTER TRANSMISSIONS : FORD TRANSMISSION INSTALLATION INSTRUCTIONS

FORD TRANSMISSION INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 15-03-2014

  Download FORD TRANSMISSION INSTALLATION INSTRUCTIONS

Download (1) Pre-installation instructions; Disconnect Battery terminal, inspect and check transmission coolant lines for damage, flush lines and coolant system thoroughly. (2) Inspect crank well for converter hub wear, and clean this area. (3) Check Flywheel for cracks and converter bolt holes for wear. (4) Inspect back of engine block where transmission mates, ensure block is clean, no wires or cables are in the way of installation. (5) Inspect and verify both dowel pins are clean and secure in block. (6) Ensure Block Plate is aligned and straight. (7) Clean area of block so transmission can make a good ground. “Warning” Transmission will suffer permanent damage if grounded improperly! Installation : (1) Transmission Fluid: you need about 10 to 12 quarts of fluid for installation, Dextron III with Mercon, 1968 – 1993 Vehicles and Mercon 5, 1994 and Newer, any brand name. (2) If transmission was purchased with a torque converter from Monster Transmission & Performance, no need to follow step (3).… Read More

  Download FORD TRANSMISSION INSTALLATION INSTRUCTIONS

2002 Dodge Truck RAM 2500 Truck AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING

Filed Under (Dodge) by admin on 01-01-2014

  Download 2002 Dodge Truck RAM 2500 Truck AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING

Download 2002 Dodge Truck RAM 2500 Truck 4WD L6-5.9L DSL Turbo VIN 6 Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Testing and Inspection Symptom Related Diagnostic Procedures. 46RE AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING Before road testing, be sure the fluid level and control cable adjustments have been checked and adjusted if necessary. Verify that diagnostic trouble codes have been resolved.Observe engine performance during the road test. A poorly tuned engine will not allow accurate analysis of transmission operation. Operate the transmission in all gear ranges. Check for shift variations and engine flare, which indicates slippage. Note if shifts are harsh, spongy, delayed, early, or if part throttle downshifts are sensitive. Slippage indicated by engine flare, usually means clutch , band or overrunning clutch problems. If the condition is advanced, an overhaul will be necessary to restore normal operation. A slipping clutch or band can often be determined by comparing which internal units are applied in the various gear ranges.… Read More

  Download 2002 Dodge Truck RAM 2500 Truck AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING

2002 Isuzu Truck Axiom Service and Repair

Filed Under (Isuzu) by admin on 06-03-2014

  Download 2002 Isuzu Truck Axiom Service and Repair

Download 2002 Isuzu Truck Axiom 2WD V6-3.5L Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Fluid – A/T Service and Repair. Changing Transmission Fluid There is no need to change the transmission fluid unless the transmission is used under one or more of the following heavy duty conditions. A. Repeated short trips B. Driving on rough roads C. Driving on dusty roads D. Towing a trailer If the vehicle is used under these conditions, change the fluid every 20,000 miles (32,000 km). 1. Place a large drain pan under the oil pan. 2. Remove the transmission oil drain screw (2) and drain fluid. 3. Tighten drain screw (2). Torque: 38 Nm (28 ft. lbs.) 4. Remove the transmission overfill screw (1) and fill transmission through overfill screw opening, using DEXRON-III ATF. Note: Add transmission fluid until it flows out over the overfill screw opening. 5. Let engine idle until a fluid temperature between 32°C (90°F) and 57°C (135°F) is reached.… Read More

  Download 2002 Isuzu Truck Axiom Service and Repair

FORD TORQUE CONVERTER & TRANSMISSION Installation Instructions

Filed Under (Ford) by admin on 06-02-2014

  Download FORD TORQUE CONVERTER & TRANSMISSION Installation Instructions

Download REMOVAL Step 1 Before you begin – let vehicle cool for about an hour. Disconnect battery. Raise vehicle and support on jack stands. The higher you raise it, the easier it is to work under. If your installing a new transmission and converter, skip to STEP 3 Step 2 Drain oil from transmission by removing the drain plug. This is a good time to install a TCI® Drain Plug Kit, TCI® #805800. Pans without plug must be slowly removed by freeing one end and allowing bolts on other end to hold pan. The pan will drop down to allow the fluid to run out the end. Use a drain pan to catch fluid. Remove remainder of bolts and slowly lower pan and pour remainder of fluid in drain pan. Replace filter and clean pan and install new pan gasket. (New gaskets and filters available from TCI®). Reinstall pan and torque pan bolts to OEM specs.… Read More

  Download FORD TORQUE CONVERTER & TRANSMISSION Installation Instructions

You might also likeclose