2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module

Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

FORD RACING M-6550-3V 4.6L 3V Camshafts INSTALLATION INSTRUCTIONS

Download
NOTES: • Purchase new VCT solenoid attachment bolts, as they are not reusable, and Silicon Gasket Sealant from a Ford Dealer. It is not recommended to use any other gasket sealant. • If doing the work in vehicle, purchase the special service tools required in the service procedures below from a Ford Dealer. a. The Wedge Tool is needed to hold the timing chain in place so the front cover does not have to be removed. This will save you a lot of time and work if you are working on an engine in a vehicle. b. If you are doing a new engine build-out of a vehicle, you will not need these tools. • Follow service procedures to remove ignition coils, oil level indicator, valve covers and camshafts. • Replace camshafts with Ford Racing camshafts: a. RH camshaft p/n: XE-6251-309994 b. LH camshaft p/n: XE-6C255-309995 • Follow service procedure to install Ford Racing camshafts, valve covers, dipstick, ignition coils and air induction system.… Read More

556H Honda / Acura Immobilizer Bypass Module Installation Instruction

Download Mode 1 Mode 2 ? Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 2002-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

Honda CBR-929RR/CBR-954RR TiForce exhaust system Installation Instructions

Download Before Installation: •Verify that all parts and accessories have been included (see list below). •Coat all exhaust pipe mating joints with anti-seize compound / lubricant (Finish Line Ti-Prep packet included). •Read and review these instructions, cautions, diagrams and images prior to starting any work. 1. Remove the lower fairing. Remove the rear turn signals. 2. Remove the existing exhaust system from the HTEV valve rearward, save the mounting bolts for reuse. Save the stock exhaust can mounting bolt and nut for the end can to the passenger footpeg for reuse as well. 3. Installthe supplied HTEV joint plate to the rear of HTEV valve (see photo 1) using the stock mounting bolts. Tighten per factory specifications. 4. Install the 2 Y-pipes to the joint plate, but do not install the supplied springs at this time. 5. Install the S-Bend tothe two Y-pipes, but do not install the supplied springs at this time.… Read More

2004-2006 Ford Double DIN Installation Kit PART 95-5812 INSTALLATION INSTRUCTIONS

Download FORD Edge 2007-2009 / Expedition 2007-2009 Explorer 2006-2009 / Explorer Sport Trac 2006-2009 F-150 2004-2008 / F Series 2005-2008 Five-Hundred 2005-2007 / Focus 2005-2007 / FreeStar 2004-2007 Freestyle 2005-2007 / Fusion 2006-2009 Mustang 2005-2009 / Super Duty 2008-2009 Taurus 2008-2009 / Taurus X 2008-2009 MERCURY Monterey 2004-2007 / Milan 2006-2008 Montego 2005-2007 / Mountaineer 2006-2009 Sable 2008-2009 LINCOLN Mark LT 2005-2009 Factory Navigation Only: MKX 2007-2009 / Navigator 2007-2009. DASH DISASSEMBLY A B C D E FORD MUSTANG 2005-2009 Remove the small rectangular shifter lever trim panel if equipped . (Figure A) 2 Remove (4) 9/32″screws from the radio to remove. (Figure E) 7 Remove (2) Phillips screws from under the center armrest at the back of the shifter trim panel (includingcup holders). (Figure B) 3 Unclip and remove panel. (Figure B) 4 Unclip and remove the (2) center stack trim panels from the left and right side of the radio and climate controls.… Read More

2008 Peugeot 308 Parrot MKi9000/MKi9100/MKi9200 Installation Guide

Download Compatibility Car models Peugeot 207: > 2006 Peugeot 308: > 2007 Peugeot 307: > 2006 Peugeot 407: > 2006. For Parrot MKi9000 / MKi9100 / MKi9200 Parrot UNIKA : PI090020AA.
The power supply for the UNIKA interface is taken from the power cable of the Parrot MKi. It is important to follow the color code of the power cable wires: the red wire of the kit’s cable corresponds to the permanent 12V supply; the orange wire corresponds to the ignition 12V ; the black wire is for ground ; the yellow wire corresponds to the Parrot mute output. Warning : Connect the ignition to the Parrot car kit if the vehicle is based on a resistive or a K-Bus protocol. Don’t connect the ignition if the vehicle is based on a CAN protocol. On some vehicles, the 12V power wires may be reversed, in which case you must reverse the red and orange wires of the hands-free kit’s power supply.… Read More

2000 Saturn SL2 Conversion Calculator

Download IMPORTANT: The important statement at the beginning of the “Ignition Lock Cylinder removal procedure on page 188 in the 2000/2001 Saturn S-Series Body/Electrical Volume II Service Manual is incorrect. Please cross out the important on that page and write in the following important statement. IMPORTANT: When replacing the ignition lock cylinder only, the passlock relearn procedure is not required. 1. Disconnect negative battery cable. 2. Remove lock cylinder bezel from steering column shroud by carefully prying with a thin bladed screwdriver. Zoom Sized for Print 3. Remove shroud fasteners and remove steering column upper and lower shroud panels. 4. Insert key into ignition lock cylinder and rotate to RUN position. ^If ignition lock cylinder can be rotated to RUN position, continue to step 30. ^If ignition lock cylinder cannot be rotated to RUN position, continue with next step. Zoom Sized for Print 5. Using a light hammer and brass drift, tap lightly on the top side of the ignition housing assembly at the location indicated in the illustration, while trying to turn the ignition key.… Read More

Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery

Download Models: 2004 Buick Rainier 2000-2004 Cadillac Escalade 2002-2004 Cadillac Escalade EXT 2003-2004 Cadillac Escalade ESV 1998-2004 Chevrolet Blazer, S-10 Pickup 1999-2004 Chevrolet Silverado 2000-2004 Chevrolet Suburban, Tahoe 2002-2004 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2004 Chevrolet Express 1998-2004 GMC Jimmy/Envoy, Sonoma 1999-2004 GMC Sierra 2000-2004 GMC Yukon, Yukon XL 2002-2004 GMC Envoy, Envoy XL 2003-2004 GMC Savana 2004 GMC Envoy XUV 1998-2004 Oldsmobile Bravada 2003-2004 HUMMER H2. #04-06-03-002: Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery – (Feb 5, 2004) When diagnosing a concern regarding an intermittent vehicle no crank or dead battery, technicians should remove and reinstall the ignition switch using the Ignition Switch Replacement procedure in the Steering Wheel and Column section of SI. The ignition switch may have been misindexed in the steering column during a previous replacement . If the ignition switch is misindexed in one direction, the ignition switch circuits will not be completely open when the ignition switch is in the OFF position with the key removed.… Read More

Honda TRX 250R MSD Enhancer Ignition System Manual Installation Instructions

Download
The MSD Enhancer Ignition system, PN KT4202, for the Honda TRX 250R ATV is designed as a complete system. No part may be substituted nor should any part be used with the stock ignition components. Note: To use the MSD Enhancer Ignition System the stock flywheel and stator assembly must be modified. This modification is not reversible.
MODIFYING THE STATOR Remove the stator assembly from the engine and secure it so it can be worked on without it moving. 1. Place the two black windings (with tape sealer) facing away from you (Figure 3). Locate the two black solder posts directly below the left black winding. The post to the left is the one we will be dealing with. This post may be coated with a black sealer. This will burn off when applying the soldering gun. Figure 3 Locating the Soldering Post of the Stator. 2. Soldered to this post is a very small wire that must be removed.… Read More

Honda / Acura Transponder Interface: TYPE “C”

Download DATA to DATA PORT (D 2D) : of D2D Cable plugs into the upgradeable vehicle interface module. OPTION A: – D2D Port used to connect to USB Bootloader adaptor & computer to download & flash vehicle interface firmware. OPTION B: – D2D Port used to connect to the data port of a remote control system equipped with ClearCode V ehicle I nterface P rotocol. Remote control systems designed with ClearCode VIP can securely communicate via the D2D cable to transmit & receive data commands which initiate specific vehicle function such as doorlocks & immobilizer override and /or request information from the vehicle such as status of entry points (doors) or ambiant température, diesel glow plug etc… ClearCode VIP represents the doorway to vehicle integration…As an enhanced security feature, this upgradeable vehicle interface module automatically detects when the Vehicle Interface Protocol is present and deactivates the analogue override input wire (brown wire) ensuring that this module can only be activated by an authorized user.… Read More