honda vtx 1800 fuse box location

You search Auto repair manual PDF about honda vtx 1800 fuse box location, search results will appear below. If search results do not exist, please search by others keyword.

Honda VTX 1800 Big Air Kit (BAK) Installation Instructions

Filed Under (Honda) by admin on 13-01-2014

Download INCLUDED IN THE KIT: (1) BAK Cover (1) Re-usable Performance Air Filter (1) Filter Raincoat (1) Mounting Post (4) M5x40 Stainless Cap Screws (2) M5x10 Stainless Cap Screws (1) Baron VTX 1800 BAK Backing Plate (1) Baron Backing Plate Adapter (2) 1/4-28 x 1 13/16″ Zinc Hex Bolts (2) 1/4″ Lock Washers (2) Aluminum Filter Spacers (3) M6x16 Hex Flange Bolts (3) External Tooth Washers (1) Reed Valve Block Off Kit BA-2561-00 (1) 3/8″ Nylon Nipple Pre-installed (1) 1/2″ Nylon Nipple Pre-installed TOOLS REQUIRED: Factory Service Manual 3, 4 & 5 mm Allen Wrenches 10, 12 & 14mm Sockets 12 & 14mm Wrenches INSTRUCTIONS: 1. Remove fuel tank per Honda service manual instructions. 2. Remove air filter box by taking out air filter element and the 4 screws around air funnels. 3. Disconnect electrical fitting from the IAT sensor (intake air temp sensor). 4. Disconnect two hoses on back of air box.… Read More

Honda / Acura SIRIUS Interface HON-SC1 INSTALLATION INSTRUCTIONS

Filed Under (Honda) by admin on 14-01-2014

Download Compatibility The HON-SC1 is designed to be compatible with select Honda/Acura vehicles. Please consult table for compatibility listing. Compatible Headunit Types: • CD only Headunits* • CD + Cassette Headunits* • 6-CD changer Headunits* • Touch Screen Monitor Headunits • Non-Touch Screen Monitor Headunits * Note: Radio must have a “SAT” or “XM” button to access SIRIUS audio modes. In addition, the HON-SC1 is compatible with most additional factory audio accessories that might be included, such as: • Rear Seat Audio Control Center • Rear Seat Entertainment (DVD/Monitor) System • Heads up display (HUD) • Steering wheel controls Note: Kit not recommended for vehicles with Technology Package (Please see Acura’s website for details). The HON-SC1 is not compatible with the factory satellite radio antenna that might be installed in the vehicle. For best operation you must install a SIRIUS compatible antenna as supplied with the compatible SIRIUS Satellite Radio tuner.… Read More

1988-1991 Honda Civic Si FUSES and CIRCUIT BREAKERS

Filed Under (Honda) by admin on 17-12-2013

Download IDENTIFICATION FUSE PANEL LOCATION The fuse box is located under dashboard on driver’s side. Underhood fuse panel is located in engine compartment beside battery. Cars equipped with anti-lock brake system have a third fuse box for ABS in front of the engine compartment on passenger’s side. FUSE PANEL IDENTIFICATION (1988-91) Fuse & Circuit Breaker Identification z 1 – 10 Amp Integrated Control Unit, Combination Switch, Gauge Assembly, Back-Up Lights Switch, Shift Position Console Switch, Clock (1990) , Shift Lock Solenoid (1990) , Interlock Control Unit (1990) Automatic Seat Belts (If Equipped) z 2 – 10 Amp Starter Solenoid, PGM-FI Main Relay, PGM-FI Electronic Control Unit, Integrated Control Unit z 3 – 20 Amp Power Door Locks (If Equipped) z 4 – 10 Amp Right Headlight High Beam, High Beam Indicator Light, Daytime Running Lights Relay (Canada) z 5 – 10 Amp Left Headlight High Beam z 6 – 30 Amp Sun Roof Motor (If Equipped) z 7 – 10 Amp Rear Lights (Canada Only) z 8 – 10 Amp Integrated Control Unit, Interior & Exterior Lighting z 9 – Blank z 10 – 10 Amp Left Headlight Low Beam z 11 – 10 Amp Right Headlight Low Beam z 12 – 15 Amp Integrated Control Unit, Luggage Compartment Light, Dome Light, Ignition Switch, Clock, Radio, Cigarette Lighter z 13 – 15/20 Amp Power Windows, Windshield Wipers & Washer, Sun Roof Relay (1990), Integrated Control Unit (Canada), Combination Switch (1990 CRX) z 14 – 10 Amp Gauge Assembly, Engine Sensors & Controls, PGM-FI Main Relay (Wagon & CRX Only), PGM-FI ECU (Wagon & CRX Only), Fuel Pump (Wagon & CRX Only), ELD Unit (Wagon & CRX Only), EACV (Wagon & CRX Only) z 15 – 15 Amp Cooling Fan Motor (Except 4WD A/T Wagon), Cooling Fan Relay z 16 – 10 Amp Daytime Running Lights (Canada Only) z 17 – 10 Amp Radio, Cigarette Lighter Relay (1990 only) z 18 – 10 Amp Rear Window Defogger, Power Door Mirrors, Air Conditioning z 19 – 30 Amp Blower Motor z 20 – 20 Amp Right Front Power Window z 21 – 20 Amp Left Front Power Window z 22 – 20 Amp Right Rear Power Window z 23 – 20 Amp Left Rear Power Window UNDERHOOD FUSE PANEL IDENTIFICATION (1988-91)Fuse & Circuit Breaker Identification z 1 – 60 Amp Power Distribution z 2 – 50 Amp Dash Fuse Box z 3 – 40 Amp Dash Fuse Box, Exterior Lighting z 4 – 10 Amp PGM-FI Electronic Control Unit, Hazard Lights, A/T Control Unit (Wagon), Integrated Control Unit (1990), Automatic Shoulder Belts (1990) z 5 – 15 Amp Horns, Brakelights, A/T Control Unit (Wagon Only), Key Interlock Solenoid (A/T Only), Seat Belt Retractors (1990) z 6 – 20 Amp Rear Window Defogger z 7 – 15 Amp PGM-FI Main Relay z 8 – 15 Amp A/C Compressor Clutch, Condenser Fan Relay… Read More

HONDA VTX 1800 Thunder Air Filter Kit Installation Manual

Filed Under (Honda) by admin on 10-01-2014

Download
HONDA FI 1800 ADAPTOR QTY PARTS LIST 1 1800 ADAPTOR 1 1/8 VACCUM PLUG 1 3/8″ L BARB 1 3/8″ RED PLUG 4 M5-. 8 X 12 SOCKET HD CAP SCREW 2 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 BLOCK OFF PLATE 1 1/8″ RED PIPE LUG 1 INSTALLATION INSTRUCTIONS.
1) Remove Seat 2) Remove tank dash. Must remove gas cap first. 3) Remove bolt-holding tank down. 4) Remove air cleaner cover and filter. 5) Remove 4 bolts in black plastic air box. 6) Lift tank and pull air box down and out. 7) Pull hoses off back and unscrew electrical probe 8) Place the 3/8″ red plug into large hose. 9 ) Hose from brass canister replace with 1/8″ vacuum plug. 10) 3/8 hose under throttle body will attach to 3/8 L-barb in new backing plate. 11) Attach electrical probe to new backing plate with screws provided.… Read More

2009 Honda Odyssey Roof Box, Short Installation Manual

Filed Under (Honda) by admin on 09-12-2013

Download
PARTS LIST Roof box 4 Brackets A 4 Brackets B 4 Plates 8 Knobs 8 Bolts 8 Washers 2 Straps Seal 2 Keys 4 Large pads 4 Small pads SUPPLIES REQUIRED Isopropyl alcohol Shop towel.
INSTALLATION NOTE: •Be careful not to damage the roof and other finished surfaces of the body when installing the roof box. •The maximum load capacity for this product is 110 lb (50 kg); approximate product weight is 29 lb (13 kg). •Do not allow the combined weight of the accessory and cargo to exceed the carrying capacity of the roof rack. •Honda roof racks or crossbars are required to install the roof box. 1. Open the roof box. Attach an adhesive seal over each of the unused mounting holes along the bottom of the box. The seals will help prevent water from entering the roof box. 2. Using isopropyl alcohol on a shop towel, clean four brackets B where the small pads will attach.… Read More

Audi A8 Parrot 3100 Bluetooth Kit Installation Instructions

Filed Under (Audi) by admin on 05-01-2014

Download Installing a Parrot 3100 Bluetooth Kit in a D3 Audi A8. This procedure is to be used in conjunction with the audipages.com checklist, wiring diagram and wiring table supplied with your kit. Remove Fuse SB13 Remove the left hand side fuse panel. This is accomplished by popping the cover off with a trim stick. Once complete, REMOVE fuse SB13 (the fuse labled 13) , which is the unswitched power to the Telematics/telephone box before starting. This will prevent inadvertent grounding of the power supply during installation. Remove Trim and Telematics Box Remove the door kick panel trim by prying it up on the aft portion of it and unclipping it, then pull the vertical portion out, it just clips out. Remove the driver’s side floor mat. Using a Torx T-35 screwdriver, remove the screw that holds the left foot rest in place. Be careful when removing the screw not to drop it down into the floor board.… Read More

HONDA VTX 1800 AIR HORNS INSTALATION INSTRUCTIONS

Filed Under (Honda) by admin on 24-11-2013

Download 1. Remove the right and left frame side covers and the seat. 2. Unplug and remove the stock horn located behind the left foot peg. Re-route the horn wires up over the front cylinder head and to the rear. Next cut two pieces of wire 36″ long, strip both ends ¼”, crimp two male spade terminals to one end and two females to the other ends. Attach these wires to the stock horn wires and route them over the rear cylinder and behind the frame tube. The end of the wires should come out near the center of the left side cover area (see photo 1 A). Connect these two wires to the relay terminals 85 & 86 (these will be the two that are parallel to each other see wiring diagram for terminal identification). 3. Using a blade screwdriver pry the two hoses with the “Y” connector off of the air horns.… Read More

Honda Civic Si Acura RSX Icebox Cold Air Intake Manual Installation Instructions

Filed Under (Acura) by admin on 01-01-2014

Download
Parts List: 1- Icebox lid w/ screws 1- Icebox Bottom 1- Lower Air Horn 1- Filter Elbow 1- 6 mm x 35 mm screw 1- 6 mm nut 1- Plastic pin 1- High Flow Filter Element 1- Filter Oil 1—CARB EO# Decal (RSX).
Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan.… Read More

2002 – 2003 Honda Civic Si & Acura RSX Comptech Icebox Cold Air Intake Installation Instructions

Filed Under (Honda) by admin on 31-12-2013

Download Parts List: 1- Icebox lid w/ screws 1- Icebox Bottom 1- Lower Air Horn 1- Filter Elbow 1- 6 mm x 35 mm screw 1- 6 mm nut 1- Plastic pin 1- High Flow Filter Element 1- Filter Oil 1—CARB EO# Decal (RSX). Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan.… Read More

Honda VTX 1800 Motorcycles Trike Conversion Installation Instruction

Filed Under (Honda) by admin on 12-12-2013

Download Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) . · Passenger Seat and mounts (to be reinstalled without modification) . NOTE: OEM front and rear seat mounting bolts to be retained and reused. · Left and right passenger foot rests and mounts (to be reinstalled with modification) . · Mufflers (to be re-installed and relocated with minor modification) . · Rear Fender (complete w/ sub frame and all attaching parts) . · Swing Arm, Drive Shaft and Rear Wheel (complete w/ brake line and all attaching parts) Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Use 17/64″ drill and drill through frame from inside out using passenger footrest mount holes as guide.… Read More

You might also likeclose