front suspension diagram on a 2002 audi a4 quattro

You search Auto repair manual PDF about front suspension diagram on a 2002 audi a4 quattro, search results will appear below. If search results do not exist, please search by others keyword.

2000-2002 Audi Quattro StartupRacing Contest and Competition Suspension Installation Manual

Filed Under (Audi) by admin on 20-01-2014

Download B5 Audi Quattro (2000-2002 Audi S4 and 1996-2001 Audi A4). Suspension Removal General 1. Loose wheel bolts 2. Raise the car and support it with two or four jack stands (if only using two, support front first, then rear) 3. Remove wheels Front 1. Remove the bolt that attaches the shock clevis to the control arm. (18mm and 19mm) 2. Remove upper control arm bolt (16mm) 3. Disconnect the upper control arms from the upright (WD40 helps here) 4. Open the hood, and remove the plastic piece hiding the battery, along with the pollen filter cover (8mm) 5. Remove these three identical bolts. They hold the upper control arm plate, as you remove the last bolt, make sure you hold the shock body as it will be loose. (16mm) Remember the orientation of washers as you remove them. 6. Remove the OEM shock along with the spring, and place on a clean flat surface.… Read More

2000-2003 AUDI A6 QUATTRO BRACKETRON PHONE MOUNT

Filed Under (Audi) by admin on 01-01-2014

Download AUDI A4, S4, QUATTRO (2000-2002) AUDI A6 QUATTRO (2000-2003) AUDI ALLROAD QUATTRO (2001-2003). NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT . All phone mount instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.TOOLS NEEDED: Two (2) sets of Audi DIN Radio Removal Tools, (Btron Part # SIT-102 One (1) Flat Headed Screwdriver or Dash Trim Tool (Btron Part # SIT-104), 5/16″ socket and driver . PARTS INCLUDED: One phone mount and instructions. LOCATION OF MOUNT: To the Right of the Radio. Installation Instructions 1. Locate four slots on the face of the radio. Insert four Audi DIN tools in these four slots until you hear or feel the tools click or lock. Note: There is a rubber seal that wraps around the radio between the radio and the dash pad.… Read More

1996 Audi/Volkswagen Bose Integration Harness

Filed Under (Audi) by admin on 11-01-2014

Download 1996-Up Audi / Volkswagen Bose Integration Harness For models amplified without Bose: 1996-03 Audi A4 / 1996-03 Audi A6 2000-01 Audi S4 / 2002-03 Audi S6 Use the White, White/Black, Gray, and Gray/Black speaker wire for the front speaker output and use the Green and Purple RCA’s for the rear speaker outputs. Be sure to connect the Blue/White wire to the aftermarket radio’s amp turn-on wire. The White and Gray RCA’s will not be used. For models amplified with Bose: 1996-03 Audi A4 / 1996-03 Audi A6 1997-03 Audi A8 / 2000-01 Audi S4 2002-03 Audi S6 / 2001-03 Audi S8 2000-03 Audi TT Use the White and Gray RCA’s for the front speaker output and use the Green and Purple RCA’s for the rear speaker outputs. Be sure to connect the Blue/White wire to the aftermarket radio’s amp turn-on wire. The White, White/Black, Gray, and Gray/Black speaker wires will not be used.… Read More

Audi A4 Quattro Suspension Kit Installation Instructions

Filed Under (Audi) by admin on 12-01-2014

Download • Remove Wheels • Remove nut (1) and bolt (2). (According to manufacturer, “Audi”, bolt and nut must be replaced) • move the two upper balljoints (3 and 4) upwards. • remove nut (5) and bolt (6). • remove caps and take off nuts (7 and 8). • remove complete shock spring assembly. • Dismantel using spring compressor • while dismantling the shock spring assembly – review the parts list. • Note: When removing the spring shock – unit consider the position of the pivot bearing (Figure 2). • Adjust lower spring seat height (see parts list, upper edge spring plate to center attachment bolt) • Installation is the reverse or removal. Note torque specs of following page. Kit instructions for threaded Suspension Kit Audi A4 Quattro • Remove Wheels • Remove nut (1) and lower damper attachment bolt (2) • Remove nut (3) and bolt (4). • Remove four bolts (Noted as 5) and remove the complete suspension assembly.… Read More

1996-2001 Audi A4 Quattro Part 57- 0515 INSTALLATION INSTRUCTIONS

Filed Under (Audi) by admin on 09-12-2013

Download Audi A4 2.4/2.8L V6 1995-2001 Audi A4 Quattro 2.8L V6 1996-2001 Audi A6 2.4/2.8L V6 1997-2002 Audi A6 Quattro 2.8L V6 1997-2001 1. Remove the cover from the air box assembly. (Fig. 1) 2. Unclip the electrical connector from the Mass Air Sensor (MAS). (Fig. 2) 3. Unclip and remove the intake hose from the MAS. (Fig. 3) 4. Unclip the evap control valve from the air box. (Fig. 4) 5. Unclip the wiring from the air box (Fig. 5) 6. Unbolt the air box mounting bolt. (Fig. 6) 7. Disconnect the auxiliary air pump hose from the front of the air box. (Under the intake scoop) 8. Carefully lift and remove the complete air box assembly from the vehicle. (Fig. 7) 9. Unbolt and remove the MAS from the air box. (Fig. 8) 10. Fit the MAS adaptor to the MAS using the hardware provided. (Fig. 9) 11. Refit the MAS to the intake hose using the original hose clip.… Read More

2002-2004 Audi A4 Sedan Radio system General information

Filed Under (Audi) by admin on 30-12-2013

Download Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – Communication. On Board Diagnostic (OBD) Radio systems have extensive On Board Diagnostic (OBD) capabilities. The radio unit has a Diagnostic Trouble Code (DTC) memory. If a malfunction occurs in one of the components or wires which is monitored by the system, a record of the type of malfunction is stored in DTC memory. Use VAS 5051 Vehicle Diagnostic, Testing and Information System in mode “Guided Fault Finding”. Retrofitting of radio systems The electrical connections on the factory- installed radio wiring harness are designed for genuine Audi radios. Radios with different types of electrical connections must be installed using adapter wires. When connecting the vehicle speed sensor signal wire (on radios with the GALA function), take particular care to avoid short circuits, which could result in vehicle malfunctions (e.g. in the engine management system). Vehicle malfunctions may also occur if the vehicle speed sensor signal wire is connected to radios supplied by other manufacturers.… Read More

Audi RS4 Quattro Part 57-0574 INSTALLATION INSTRUCTIONS

Filed Under (Audi) by admin on 10-12-2013

Download Audi RS4 Quattro 2.7L V6 ‘Bi-Turbo’ Apr’00- 1. Disconnect the negative terminal from the battery. 2. Remove the plastic cover from the air box assembly. (Fig. 1) 3. Remove the air box feed pipe from between the air box lid & slam panel intake scoop. (Fig. 2) 4. Unclip & remove the electrical harness plug from the MAS (Mass Air Sensor). (Fig. 3) 5. Unclip & remove the intake hose from the MAS. (Fig. 4) 6. Unclip the 3 hoses from the top of the air box assembly. (Fig. 5) 7. Unbolt & remove the two ignition amplifiers from the top of the air box lid. (Fig. 6) 8. Unclip & remove the air box lid & filter from the vehicle. (Fig. 7) 9. Remove the small vacuum tube from the hose located at the base of the air box assembly. (Fig. 8) 10. Remove the bolt securing the air box assembly to the inner wing & carefully remove the assembly from the vehicle.… Read More

2000-2002 AUDI A4 Multi Vehicle Mount MVM-45-05

Filed Under (Audi) by admin on 27-03-2014

Download AUDI A4 – 2000-2002 AUDI S4 – 2000-2002 AUDI A6 – 2000-2005 AUDI-ALLROAD – 2000-2005 Mount Location: To the Right of the Radio. Multi Vehicle Mount MVM-45-05 Includes PHS-203 Ultra Slim Swivel. DASH DISASSEMBLY INSTRUCTION Locate the four slots on the face of the radio. Insert the Audi DIN tools in these four slots until you hear a click or lock. Note: There is a rubber seal that wraps around the radio between the radio and the dash pad. This causes the radio to sit very tightly in the cavity. To loosen this seal and allow the radio to slide out easier, we recommend using a Dash Trim Tool to wedge between both the right and left sides of the radio dash pad. Carefully wiggle the tool to loosen the radio slightly. Grasp the four DIN tools and slide the radio out of its cavity just enough to allow access to the one (1) 5/16″ hex head bolt that holds the climate control in place.… Read More

2000-2002 AUDI A4 PART AU-54-00 INSTALLATION INSTRUCTIONS

Filed Under (Audi) by admin on 04-04-2014

Download AUDI A4, A6, S4, QUATTRO (2000-2002) AUDI ALLROAD QUATTRO (2001-2002) PART NUMBER: AU-54-00. STEP1. Begin by removing the radio. CAUTION: Do not disconnect any wiring to the radio at any time. Insert four (4) radio removal tools into the removal slots. (See photo #1.) There is an anti-vibration o-ring located behind the radio trim bezel that needs to be loosen in order to slide out the radio. With the radio removal tools in place, insert a smooth , thin, flat bladed screwdriver in between the radio trim bezel and the dash pad on the right side of the radio. (See black dots in photo # 1). Wiggling the screwdriver gently will release the o-ring and radio from the dash. After completing the same procedure on the left side, slide the radio forward enough to access the two (2) 5/16″ hex bolts on the right side of the radio cavity. (See photo # 2).… Read More

2008 Audi A4 Custom Body Side Molding PART FE-AUDI-A4 INSTALLATION INSTRUCTIONS

Filed Under (Audi) by admin on 01-12-2013

Download FOR: 2008 + Audi A4. PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION 1. LOCATION ( See Diagram below ): Using masking tape, run the tape as seen in Diagram below from POINT A to POINT B. Press tape against the vehicle, making sure that the tape is straight from POINT A to POINT B. 2. CLEAN AND PREP : For proper installation of Custom Body Side Molding, clean the surface where the molding is to be installed using the alcohol pads enclosed. Wipe off excess residue with a clean cloth. Apply PRO- BOND ADHESIVE PROMOTOR in the crush swab self-applicator. Squeeze the applicator until you feel the applicator “crush”. The applicator will become wet on the end and is ready for use. Quickly apply a thin coat of PRO-BOND below the masking tape line, no further than 1 ¼” below the tape. Be careful not to go lower than 1 ¼” because PRO-BOND could dull the paint surface.… Read More

You might also likeclose