FORD PATS (PASSIVE ANTI THEFT SYSTEM) INITIALIZATION WITH THE 2534 GLOBAL PROGRAMMER

Download There are five types of PATS implementations from Ford (A, B, C, D, E). Refer to Table 1 (page 11) to identify what type of PATS your vehicle is equipped with. PATS initialization is generally performed after programming. The A or D version of PATS does not store the key information in the PCM, therefore NO PATS KEY RELEARN IS REQUIRED after programming. The B or C versions of PATS store the key information within the PCM and MUST be transferred to the new PCM, or relearned on the vehicle after the new PCM is installed. The E version of PATS also stores the key information within the PCM, but CANNOT be transferred to the new PCM. This type MUST be relearned on the vehicle after the new PCM is installed. Note: If you are just updating the existing PCM calibration with an update calibration, you must select the MODULE REPROGRAMMING function (not Programmable Module Installation).… Read More

Ford-Toyota-Lexus 555F Interface Module Wiring Installation Instructions

Download The 555F interface module is used when installing remote start products in Ford, Toyota and Lexus vehicles equipped with factory immobilizers. The 555F allows for easy interfacing between the remote start and the factory immobilizer, while maintaining the integrity of the OEM system. WIRE CONNECTION GUIDE FOR FORDS RED (+)12V: Connect this wire to a fused (+)12V source. BLUE (-) ACTIVATION INPUT: Connect this wire to the (-) through activation output of the remote start system. 555FCAPSULE: The 555F capsule should be placed on the outside of the antenna ring as close to the ribbon cable as possible. LEARNING THE 555F CAPSULE FOR FORDS To program the 555F capsule for a Ford vehicle, use the procedure that corresponds to the appropriate vehicle year. 1996 and 1997 Ford Vehicles: 1. Install the remote start and make the appropriate wire connections on the 555F. 2. Make sure that the 555F capsule can reach the front of the key cylinder where the key is inserted.… Read More

1997 – 2001 Infiniti Q45 ENGINE WILL NOT START

Download 2000 – 2001 I30 (CA33) 1999 I30 (CA32) 1999.5 – 2001 QX4 (JR50) 1997 – 2001 Q45 (FY33) 2000 – 2001 G20 (P11) APPLIED VINS: All APPLIED DATES: Start of production SERVICE INFORMATION This bulletin describes and introduces new features of the Infiniti Vehicle Immobilizer System/Nissan Anti-Theft System (IVIS/NATS). The system is standard equipment on each of the applied vehicles listed above. The IVIS/NATS will not allow the engine to start without the use of a registered ignition key. If a vehicle will not start and the Security lamp is on solid, it may be because the ignition keys were not properly registered into the vehicle’s NATS IMMU (Immobilizer control unit). In this case, there will be a “DIFFERENCE OF KEY” code stored in the NATS IMMU. When the NATS ignition key, IMMU, or ECM (ECCS control unit) are replaced, C/U initialization is necessary. It is also necessary when registering keys and as part of many NATS Service Manual diagnostic procedures.… Read More

1998 – 2001 Ford Explorer 4WD Ford Ranger Explorer Sport Trac / Edge Mountaineer 4WD Torsion bar key front leveling kit

Download Part # 22907 1998 – 2001 Ford Explorer 4WD 1998 – 2007 Ford Ranger / Explorer Sport Trac Edge / Mountaineer 4WD Torsion bar key front leveling kit Part# Description Qty. 22907-01 Torsion bar keys 2 22907INST Instruction manual (customer copy) 1 22907INST Instruction manual (installer copy) 1 WARNINGDECAL Warning decal 1 MIRRORHANGER Rear view mirror hanger 1. Important customer information: Tuff Country EZ-Ride Suspension highly recommends that a qualified and/or certified mechanic performs this installation. If you desire to return your vehicle to stock, it is the customers responsibility to save all stock hardware. This vehicles reaction and handling characteristics may differ from standard cars and/or trucks. Modifications to improve and/or enhance off road performance may raise the intended center of gravity. Extreme caution must be utilized when encountering driving conditions which may cause vehicle imbalance or loss of control. DRIVE SAFELY! Avoid abrupt maneuvers, such as sudden sharp turns which could cause a roll over, resulting in serious injury or death.… Read More

Ford Focus Rear Suspension Tool Trailing Arm Bushes Installation Instructions

Download Rear Suspension Tool for the rear Trailing Arm Bushes on Ford Focus 1.4 | 1.6 | 1.8 | 1.8Di 1.8TDCi | 2.0 16v RS. This tool is designed to fit in situ saving time and money. Removal 1 Remove shock absorber, lower mounting bolt, ABS brake sensor etc and wedge the lower arm in place to gain access to the bush. 2 To ensure the correct alignment is achieved mark the inner wing of the bush against the arm. 3 Lubricate generously the stud threads and bearing assembly before and during use. 4 To remove the old bush, assemble tool as shown in (Fig 1) using removal sleeve. 5 The tool should be pushing in to the centre from the outside (Fig 1) 6 Screw up the Main Drive Bar until the Thrust Bearing assembly makes contact with the bush. 7 Continue to tighten slowly using a 21mm spanner or ratchet on the hex end.… Read More

1100F FORD PATS / SECURILOCK REMOTE START INTERFACE-DATA

Download PRODUCT ACCESSORIES DESCRIPTION The 1100F interface module is used when installing remote start products in Ford vehicles equipped with a factory immobilizer. The 1100F allows for easy interfacing between the remote start and the factory immobilizer, while maintaining the integrity of the OEM system. The factory transponder-based anti-theft system uses a small electronic chip hidden in the key to send a code to the vehicle’s transceiver when the ignition is energized. The key must be placed in the ignition and turned to the RUN position. This energizes a coil surrounding the key, which in turn energizes the chip, which sends a code to the vehicle. If the vehicle does not detect the code being sent, the vehicle will start and then immediately shut off or will just crank, and the anti-theft light will flash. The 1100F provides a valid code to the vehicle whenever it is remote started, but does not affect the immobilizer system during normal vehicle operation; the immobilizer system remains fully functional.… Read More

1997 F150 – Ford Expedition Radio Replacement Installation Instructions

Download Parts REQUIRED for the install Description Snap on in dash wire harness ** Please read instructions first Radio dash installation kit 1999 Ford F150/Expedition kit Optional parts for this install None. Remove Factory Radio STEP 1 : The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash.… Read More

1990 – 1995 Ford Taurus Mercury Sable Radio Replacement Installation Instructions

Download Remove Factory Radio STEP 1 : The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio. This vehicle may have the Ford Premium Sound System installed in the vehicle. When you pull the Ford radio out of the dash, there may be a square connector plugged into the rear of the Ford radio. If there is a square plug, then your vehicle has amplifiers.… Read More

COMP Cams® Ford Timing Set Installation Instructions

Download Ford Timing Set Installation Instructions Thank you for choosing COMP Cams® products! We know you have options in valve train component selection and we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and also take a moment to review the included limited warranty information. Engine Application High Energy Magnum Hi-Tech Ford V6, 144-200 3223 Ford V6, 171 (2600-2800cc) 3236 Ford V8, 255, 289, 302 & Boss 302, 1965-1988 2120 3120 Ford V8, 289-351W & Boss 302, pre 1972 3220 Ford V8, 302-351W, 1972 & up 3230 Ford V8, 352-428, 1964-1974 3208 2108 3108 Ford V8, 351C, 351M, 400M, 1970-1982 3221 2121 3121 Ford V8, 429-460, 1968-1971 3222 2122 3122 Ford V8, 429-460, 1972-1987 2130 3130 Ford V8, 429-460 w/nine keyway crank gear 2134* Ford V8, 351W, 351W H.O., 1969-¹84 2135 3135 Ford V8, 5.0L 302 H.O., 1980-March 21, 1984 2131 3131 Ford V8, 5.0L 302, 351W, March 22, 1984-1992 2138 3138 Notes: * #2120 or #3120 should not be installed on 351W engines as they are designed for 255, 289, 302 or Boss 302 engines.… Read More

1996 Ford Taurus V6-182 3.0L – Service and Repair

Download : Prior to removal of the Camshaft Position (CMP) sensor, set cylinder No.1 to zero degrees Top Dead Center (TDC) of compression stroke. Then note the position of the CMP sensor electrical connector. The installation procedure requires that the connector be located in the same position. 1. Disconnect battery ground cable. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the Powertrain Control Module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. 2. Disconnect engine control sensor wiring connector from CMP sensor. 3. Remove retaining screws and CMP sensor from sensor housing. 4. If removing CMP sensor housing from the cylinder block, proceed with Removal Step 5. If not removing sensor housing, proceed to installation Step 6. 5. Remove hold-down clamp (bolt and washer assembly) . 6. Remove CMP sensor housing from cylinder block.… Read More