Ford C-4 Trans-Brake Reversed Pattern Manual Installation Instructions

Download Recommended Options: 72803 6 Clutch Drum Assembly 72203 Direct Clutch Kit (6) Blue List of Enclosed Parts (1) Valve Body Assembly (1) Billet Intermediate Servo Cover (1) Solenoid Mounting Block (1) Solenoid Mounting Clip (1) 5/16-18 X 5/8 Whiz Lock Bolt (Solenoid Mounting) (1) Brake Valve (1) Brake Valve Spring (1) Solenoid and Pin Note: Prior to beginning installation of this Trans-Brake kit it is recommended that you be knowledgeable in the assembly of your transmission. If necessary consult a manual or seek the advice of a transmission shop. The transmission must be properly rebuilt for racing before installation of this Trans-Brake. 1.Remove the transmission pan and existing valve body. 2.Ford designates its intermediate servos by letters which appear on the servo cover (A, H, R, K, O, etc.). Note this designation, if your transmission is equipped with a “K” or “R” servo it must be replaced with a servo which has a larger diameter that seals in the bore of the case rather than the bore in the cover.… Read More

2008 Ford Escape FLUID LEAK TRANSMISSION FLUID COOLER

Download FORD: MERCURY: 2008 Escape 2008 Mariner This article supersedes TSB 08-16-12 to change the OPERATION DESCRIPTION TIME production fix date. 090904A 2008 Escape/Mariner1.1 Hrs. CD4E Transmission: ISSUE Replace The Transmission Some 2008 Escape and Mariner vehicles (excluding Fluid Cooler, Includes Hybrids) built on or before 5/9/2008 and equipped Time To Remove And with a CD4E transmission may exhibit a fluid leak Install Bumper Cover, from the transmission cooler. Evacuate And Charge Air Conditioning System, Top ACTION Off Transmission Fluid (Do Follow the Service Procedure steps to correct the Not Use With 19700A, condition. 19700A7) DEALER CODING SERVICE PROCEDURE CONDITION BASIC PART NO. CODE Replace the transmission / A/C cooler with a new 19712 07 updated part following Workshop Manual (WSM), Section 412-01. PART NUMBER PART NAME 8L8Z-19712-J Transmission / A/C Cooler WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage IMPORTANT: Warranty coverage limits/policies are not altered by a TSB.… Read More

Ford BD Performance Transmission Installation Instructions

Download
REMOVAL: 1) Disconnect the negative battery cable(s). 2) Place the transmission into the Neutral (N) position. 3) Raise the vehicle on a hoist. 4) Mark the drive shaft and pinion yokes for assembly alignment. On 4WD models, remove the skid plate. 5) Remove the transmission oil filter tube nut and filler tube. 6) Position a drain pan & disconnect the transmission fluid cooler tubes at the cooler bypass valve. 7) Remove the drive shaft. On 4WD models, remove the front drive shaft & transfer case assembly. On SuperDuty/Motorhome models, remove the transmission mounted parking brake assembly. 8) NOTE: If the vehicle is equipped with a PTO (Power Take-Off) unit, all or part of the PTO will need to be removed. 9) Disconnect the shift cable from the transmission and manual lever. 10) Disconnect the cable housing from the bracket. 11) Disconnect the digital transmission range (TR) sensor connector. 12) Remove the transmission heat shield.… Read More

MONSTER TRANSMISSIONS : FORD TRANSMISSION INSTALLATION INSTRUCTIONS

Download
Please Note : The following instructions were made to act as a guide/reference, if you are inexperienced with performing an automatic transmission installation it is highly recommended that you contact a certified experienced professional to perform the installation and/or make the proper adjustments for you! Instructions : (1) Pre-installation instructions; Disconnect Battery terminal, inspect and check transmission coolant lines for damage, flush lines and coolant system thoroughly. (2) Inspect crank well for converter hub wear, and clean this area. (3) Check Flywheel for cracks and converter bolt holes for wear. (4) Inspect back of engine block where transmission mates, ensure block is clean, no wires or cables are in the way of installation. (5) Inspect and verify both dowel pins are clean and secure in block. (6) Ensure Block Plate is aligned and straight. (7) Clean area of block so transmission can make a good ground. “Warning” Transmission will suffer permanent damage if grounded improperly!… Read More

FORD TORQUE CONVERTER & TRANSMISSION Installation Instructions

Download REMOVAL Step 1 Before you begin – let vehicle cool for about an hour. Disconnect battery. Raise vehicle and support on jack stands. The higher you raise it, the easier it is to work under. If your installing a new transmission and converter, skip to STEP 3 Step 2 Drain oil from transmission by removing the drain plug. This is a good time to install a TCI® Drain Plug Kit, TCI® #805800. Pans without plug must be slowly removed by freeing one end and allowing bolts on other end to hold pan. The pan will drop down to allow the fluid to run out the end. Use a drain pan to catch fluid. Remove remainder of bolts and slowly lower pan and pour remainder of fluid in drain pan. Replace filter and clean pan and install new pan gasket. (New gaskets and filters available from TCI®). Reinstall pan and torque pan bolts to OEM specs.… Read More

FORD TRANSMISSION INSTALLATION INSTRUCTIONS

Download (1) Pre-installation instructions; Disconnect Battery terminal, inspect and check transmission coolant lines for damage, flush lines and coolant system thoroughly. (2) Inspect crank well for converter hub wear, and clean this area. (3) Check Flywheel for cracks and converter bolt holes for wear. (4) Inspect back of engine block where transmission mates, ensure block is clean, no wires or cables are in the way of installation. (5) Inspect and verify both dowel pins are clean and secure in block. (6) Ensure Block Plate is aligned and straight. (7) Clean area of block so transmission can make a good ground. “Warning” Transmission will suffer permanent damage if grounded improperly! Installation : (1) Transmission Fluid: you need about 10 to 12 quarts of fluid for installation, Dextron III with Mercon, 1968 – 1993 Vehicles and Mercon 5, 1994 and Newer, any brand name. (2) If transmission was purchased with a torque converter from Monster Transmission & Performance, no need to follow step (3).… Read More

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)

Download Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) #05-07-30-031: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) – (Nov 11, 2005) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case.… Read More

FORD RANGER FULL TAILGATE COVER SUGGESTED INSTALLATION INSTRUCTIONS

Download The full tailgate cover is designed to fit over the complete tailgate with no seams exposed on the rear face of the tailgate. It covers the original handle area so another latch mechanism which operates from the inside of the tailgate may be used. A Tailgate handle relocator kit is available. If this method is to be used, it must be done now before installing the tailgate cover. 1. Tailgate should be removed from the truck. 2. Be sure the latch mechanism is modified and working correctly. After the cover is installed the original mechanism is not accessible. 3. Straighten the tailgate if it is bent or twisted. If installing a louvre cover, paint the rear face of the tailgate with a flat black paint to prevent the original paint from showing through the louvres. Any distortion in the top of the tailgate should be repaired to allow the cover to follow the original tailgate contour.… Read More

1995 Ford Scorpio Transmission Range Sensor Installation Instructions

Download Remove 1. Move the selector lever to position “N”. 2. Raise the vehicle. 3. Unhook the loops for the rear exhaust pipe. 4. Detach the front heat shield and slide it backwards. 5. Detach the bracket for the front exhaust pipe from the transmission crossmember and swivel it downwards. NOTE: Support the automatic transmission with a transmission jack. 6. Detach the transmission crossmember. 1Detach it from the body. 2Detach it from the automatic transmission. Lower the automatic transmission and remove the transmission jack. 7. Detach the selector lever. 1Unclip the link rod from the selector lever. 2Selector lever 3Nut 4Selector shaft. 8. Disconnect the plug of the TR switch and remove the TR switch. Install NOTE: The guide of the TR switch must engage with the groove of the selector shaft. 9. Install and adjust the TR switch. NOTE: Do not tighten the bolts. 1Attach the TR switch. 2Slide on the selector lever and turn the selector shaft anti-clockwise as far as the stop.… Read More

Ford Super Duty 4×4 Mag Hytec Rear Diff Cover Install and Rear Diff Gear Oil Change 2004 F250 4×4 XLT Sport Crew Cab

Download TOOLS & PARTS I USED – Mag-Hytec Ford 10.5 rear differential cover – Redline #57914 75W140 gear oil, 6 quarts – 1/2″ socket & ratchet (cover bolt removal) – Flat screwdriver – Torque wrench – Drain pan – Several rags – Plastic putty paddle – Small funnel – Lacquer thinner – 1/4″ allen wrench (new cover bolt install) PROCEDURE Here’s a few pics of the Mag Hytec cover. Its a very impressive cover, complete with additional oil capacity, a magnetic dipstick, a drain plug, a 1/8 NPT port (for a temperature sending unit), and an o-ring to seal to the rear diff case. Here’s a shot of the dipstick (left) and temperature sender port. Here’s a pic of the drain plug on the bottom. Dipstick removed
Drain plug removed Here’s the stainless hardware that’s included with the cover. They also include the two sizes of allen wrenches needed for the installation of the bolts and to service the drain plug/diptstick/sender port.… Read More