evap control system ford focus p0442

You search Auto repair manual PDF about evap control system ford focus p0442, search results will appear below. If search results do not exist, please search by others keyword.

DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected

Filed Under (Other Manuals) by admin on 17-01-2014

Download DTC P0442 Evaporative Emission (EVAP) System Small Leak Detected Refer to Engine Controls Routing Diagram, EVAP Control System Overview . System Description This DTC tests the evaporative emission (EVAP) system for a small leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the vacuum decay rate. At an appropriate time, the control module turns the EVAP canister purge valve ON and the EVAP vent valve ON. This allows the engine to draw a vacuum on the EVAP system. At a calibrated time, or vacuum level, the control module turns the EVAP canister purge valve OFF, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum decay. If the control module detects a leak larger than a calibrated amount, this DTC sets. The following table illustrates the relationship between the ON and OFF states, and the Open or Closed states of the EVAP canister purge and vent valves.… Read More

2000-2004 Ford Focus ZX3 SVT Suspension Kit INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 17-03-2013

DownloadPARTS IN KIT: ITEM # QTY DESCRIPTION SERVICE PART # REPLACEMENT SOURCE 1 2 Spring, rear 2M5Z-5B669-AA Ford Dealer 2 2 Shock, rear 2M5Z-18125-BA Ford Dealer 3 1 Anti-roll bar, rear 1S4Z-5A772-BA Ford Dealer 4 1 Strut, RF 2M5Z-18124-BA Ford Dealer 5 1 Strut, LF 2M5Z-18124-BB Ford Dealer 6 2 Bump stop 2M5Z-3020-AA Ford Dealer 7 2 Spring, front 2M5Z-5310-AA Ford Dealer 8 2 Nut, upper strut piston W700212-S3091 Ford Dealer. TORQUE SPECIFICATIONS: FASTENER TORQUE (ft./lbs.) (EXCEPT WHERE NOTED) Rear shock upper mount nut 13 Rear shock lower mount nut 85 Rear lower control arm to knuckle 85 Rear anti-roll bar to control arm bolts 11 Rear anti-roll bar bushing clamp bolts 35 Upper strut piston nut 35 Strut tower nuts 18 Knuckle to strut bolt 66 Front anti-roll bar link to strut bolt 94 Caliper to Knuckle 21 Wheel nuts 37. REAR SUSPENSION INSTALLATION INSTRUCTIONS: STEP 1: Raise vehicle off ground and support with jack stands.… Read More

Ford Mustang Fuel Injection Conversion

Filed Under (Ford) by admin on 04-05-2012

Download These instructions will provide the basic and necessary information to allow a carbureted 302 to be converted to SEFI Fuel Injection. There are several different types of fuel injection conversions available, however, this instruction will concentrate on the High Output, MASS-AIR setups found on the 92-93 Ford Mustangs. There are two main advantages to using this type of setup. The first advantage is that the computer in the MASS-AIR system will automatically compensate for any engine modifications that have been done prior to the installation of the fuel injection system. The second advantage is that fuel is sent to each cylinder individually only during the appropriate firing cycle, meaning that fuel is sent sequentially to each cylinder only when the spark plug is ready to fire. This makes for an extremely efficient firing cycle . SEFI stands for Sequential Electronic Fuel Injection. This system is complex to be sure, therefore, this instruction is going to skip all the technical mumbo-jumbo, and focus on the bare essentials to install this system properly.… Read More

FORD Focus Edge Fusion Interface Installation Manual

Filed Under (Ford) by admin on 19-03-2014

Download This interface can insert RGB navigation/2AV/Camera signal onto Ford Focus, Edge ,Fusion and other ford screen. Features of this interface: ? It is compatible with all Ford 4Pin LVDS screen CD/screen systems which are available in Focus, Edge? ,Fusion and more, they have separate CD unit and screens. ? 64Mega dynamical memory is used inside for 2-dimensional spatial zoom and guarantee stable video signal to panel no matter what the input video source the installer use.[PAL/NTSC/No signal] ? Plug and play installation without hurting the original circuit and warranty label, Special PPS shell makes this interface stable against noise, Low EMI, and very reliable.[the black plastic shell is actually conductive] ? Optional Touch operation to installed DVD/TV tuner can be activated, so the installer can operate DVD without using the remote controller. ? Optional control port for installer’s expanding convenience, the control port has a Audio Relay selection trigger voltage ,also one touch screen selection trigger voltage, so the user can original touch screen for installer navigation unit, this is especially good for imported ford cars.… Read More

MSD Blaster Ford Focus 4-Tower Coil Pack PN 8241 Installation Guide

Filed Under (Ford) by admin on 03-04-2014

Download
*IMPORTANT: Read instructions before attempting the installation. Parts Included: 1 – Blaster Ford 4-Tower Coil Pack 4 – Socket Head Cap Screws 4 – Aluminum Spacers 4 – Star Washers * *WARNING: During installation, disconnect the battery cables. When disconnecting the battery, always remove the Negative cable first and install it last. Note: If the Coil Pack is being installed on a ’99-’04 Ford Focus Zetec, the spark plug wires will require replacement. MSD offers a set, as PN 32939. This MSD Ford 4-Tower Coil is designed as a replacement coil and produces a high voltage spark. To get even more ignition performance, install an MSD DIS Series Ignition Control (See Figure 3). 1. Note their position, then remove the coil wires, harness and the four retaining screws. 2. Remove the factory coil. 3. Install the new MSD Coil and retaining screws (On ’99-’04 Focus 2.0L engines, refer to Figure 2).… Read More

2005-2007 NISSAN PATHFINDER MIL “ON” WITH DTC P0442/P0448/P0455/P0456/P1446

Filed Under (Nissan) by admin on 02-01-2014

Download IF YOU CONFIRM: A MIL “ON” with one or more of the following DTC(s) stored: • P0442 / P0448 / P0455 / P0456 / P1446 AND • EVAP Vent Control S/V is stuck open or will not seal when operated/closed. ACTIONS: 1. Replace the EVAP Vent Control S/V. 2. Install the Filter Kit (refer to the Service Procedure in this bulletin). 3. Clear any DTCs stored in the ECM. SERVICE PROCEDURE Replace Vent Control Valve 1. Replace the EVAP Vent Control S/V. • Refer to section EC in the Service Manual for replacement information. Install Filter Kit 1. Remove the spare tire. 2. Remove the EVAP canister mounting bolt (see Figure 1). • The canister will drop about 3 inches which will give you working room at the top. 3. Disconnect the vent hose (see Figure 1). 4. Reach above the EVAP canister and disconnect the vent hose at the vent control valve and remove the hose (see Figure 2).… Read More

2000-2004 Ford Focus Rear Kit 75630 Installation Instructions

Filed Under (Ford) by admin on 05-02-2014

Download Always keep safety in mind when working on your vehicle. I. Preparing the Vehicle 1. Begin the installation by elevating the car. Secure the frame with jack stands (Figure 1). 2. Remove the rear wheels. 3. Remove the sway bar from the framerail and discard. II. Removing the Rear Suspension 1. Remove the lower shock bolt and retain. 2. Jack the vehicle up until the coil spring is loose enough to be removed (Figure 2). 3. Remove the bolts on both sides of the lower control arm and retain. 4. Remove the lower control arm and discard. III. Assembling the Air Spring Assembly 1. Place the air sleeve upper end cap to the under side of the mounting bracket (B) using two bolts (I), flat washers (L) and lock washers (J) (Figure 3). Torque to 25 ft/lbs. 2. Place the air fitting (K) onto the end of the sleeve. IV.… Read More

2000-UP FORD FOCUS 4 Door Sedan / Wagon, 3 Door Hatchback Audio Installation Instructions

Filed Under (Ford) by admin on 31-12-2013

Download Preliminary: disconnect the negative battery cable. Antenna: the factory antenna is located in the center front of vehicles roof. Radio removal and in-dash installation: note: the factory radio provision is a custom ford double din. When installing an aftermarket din stereo a dash kit is needed. We recommend the scosche fm1375 or fmc1370 installation kit. A set of din removal tools is also needed to remove the factory head unit. We recommend the scosche dt-1 ford din removal tools. 1. Insert ford din removal tools to release clips, pull out stereo, disconnect and remove. Front door speaker installation: note : the factory speaker provision is for a 6 x 8″ speaker. When installing an aftermarket 5 ¼ or 6 ½ speaker, a speaker adapter is required. We recommend the scosche sa68. 1. Extract (7) t-15 torx screws from the perimeter of door panel. 2. Remove screw cover from door opener cup, and extract (1) # 2 philips head screw from behind.… Read More

1999-2000 Ford Windstar The battery light is on, but the alternator is charging Has a code P1246

Filed Under (Ford) by admin on 18-01-2014

Download Direct-Hit 2000 Ford Windstar 3.8L Test Details Hotline Archive # 124501 Confirmed Fix Vehicle Application: 1999 Ford Windstar 3.8L, Vin 4 2003 Ford Windstar 3.8L 2000 Ford Windstar 3.8L, Vin 4 Customer Concern: The battery light is on, but the alternator is charging. Has a code P1246. Tests/Procedures: 1. Disconnect the alternator and the Powertrain Control Module (PCM). Check the Violet (VT) (GENerator MONitor or GENMON) wire from the alternator to pin 20 of the PCM connector and the Red/Pink (RD/PK) (GENerator COMmand or GENCOM) wire from the alternator to pin 45 of the PCM for high resistance, an open, or a short to ground. Repair the wiring as needed. 2. If the wiring checks OK, reconnect the PCM and alternator. Start the engine and monitor the VT wire for a roughly 0-10v square wave signal. The signal will be around 40-50% normally with no loads on the system and minimal charging system output.… Read More

1998 – 2001 Ford Explorer 4WD Ford Ranger Explorer Sport Trac / Edge Mountaineer 4WD Torsion bar key front leveling kit

Filed Under (Ford) by admin on 15-02-2014

Download Part # 22907 1998 – 2001 Ford Explorer 4WD 1998 – 2007 Ford Ranger / Explorer Sport Trac Edge / Mountaineer 4WD Torsion bar key front leveling kit Part# Description Qty. 22907-01 Torsion bar keys 2 22907INST Instruction manual (customer copy) 1 22907INST Instruction manual (installer copy) 1 WARNINGDECAL Warning decal 1 MIRRORHANGER Rear view mirror hanger 1. Important customer information: Tuff Country EZ-Ride Suspension highly recommends that a qualified and/or certified mechanic performs this installation. If you desire to return your vehicle to stock, it is the customers responsibility to save all stock hardware. This vehicles reaction and handling characteristics may differ from standard cars and/or trucks. Modifications to improve and/or enhance off road performance may raise the intended center of gravity. Extreme caution must be utilized when encountering driving conditions which may cause vehicle imbalance or loss of control. DRIVE SAFELY! Avoid abrupt maneuvers, such as sudden sharp turns which could cause a roll over, resulting in serious injury or death.… Read More

You might also likeclose