disc brake anti rattle clip front on 2001 chevrolet silverado hd

You search Auto repair manual PDF about disc brake anti rattle clip front on 2001 chevrolet silverado hd, search results will appear below. If search results do not exist, please search by others keyword.

2003 Volvo S40 Replacing The Rear Brake Pads

Filed Under (Volvo) by admin on 29-12-2013

Download 2003 Volvo S40 L4-1.9L Turbo VIN 27 B4204T4 Vehicle Level Brakes and Traction Control Disc Brake System Brake Pad Service and Repair Rear Brake Pads. Replacing The Rear Brake Pads Special Tools: 999 5782, 951 2834 General CAUTION: Replace the brake pads when the minimum thickness is 2 mm . Removing the rear brake pads Remove * the hub cap and the wheel * the retaining clip and the brake hose from the support * the upper bolt from the locating pin for the brake caliper . Twist the brake caliper backwards. Remove the brake pads. NOTE: Do not depress the brake pedal while the brake pads are removed. Checking and cleaning the rear brake calipers. Clean brake pad contact surfaces in the brake caliper and on the caliper mounting. Check the dirt guard for the piston. Replace the dirt guard if it is worn. Recondition the brake caliper if the dirt guard is defective.… Read More

2001 Dodge Truck Grand Caravan FRONT DISC BRAKE SHOES

Filed Under (Dodge) by admin on 02-01-2014

Download 2001 Dodge Truck Grand Caravan FWD V6-3.8L VIN L FRONT DISC BRAKE SHOES (DISC/DISC BRAKES) REMOVAL 1. Raise the vehicle. 2. Remove both front wheel and tire assemblies. 3. Begin on one side of the vehicle. 4. Remove the anti-rattle clip from the outboard side of the caliper and adapter. 5. Remove the two caliper guide pin bolts. 6. Remove caliper from caliper adapter and brake rotor. CAUTION: Supporting weight of caliper by the flexible brake fluid hose can damage the hose. 7. Using wire or cord, hang the caliper from the front strut assembly. Support the caliper firmly to prevent weight of caliper from being supported by the brake fluid hose. 8. Remove the outboard brake shoe from the caliper adapter. 9. Pull the inboard brake shoe away from the caliper piston until the retaining clip on shoe is free from the cavity in the caliper piston. 10. Repeat the above procedure on other side of the vehicle.… Read More

2001 Chevrolet Chevy K Silverado Crankshaft Position Sensor Engine Stall

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download Models: 2001 Chevrolet Silverado, Suburban 2001 GMC Sierra, Yukon XL Equipped with 8.1L V8 (RPO L18 – VIN G) Engine. Condition General Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 2001 model year Chevrolet Silverado, Suburban; GMC Sierra and Yukon XL model vehicles, equipped with an 8.1L V8 (RPO L18 – VIN G) engine. Some of these vehicles have a condition in which the crankshaft position sensor can fail intermittently or permanently. If the sensor fails intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool down period. If the sensor fails permanently, the engine will quit running and will not re-start. Correction Dealers are to replace the crankshaft position sensor. Vehicles Involved Involved are certain 2001 model year Chevrolet Silverado, Suburban; GMC Sierra and Yukon XL model vehicles, equipped with an 8.1L V8 (RPO L18 – VIN G) engine and built within these VIN breakpoints: Subject: 06083 — Crankshaft Position Sensor Engine Stall Models: 2001 Chevrolet Silverado, Suburban 2001 GMC Sierra, Yukon XL Equipped with 8.1L V8 (RPO L18 – VIN G) Engine Year Division Model From Through 2001 Chevrolet Silverado iE100004 1E200999 1F100006 1F116767 1M100002 1M103668 1Z100010 1Z100042 2001 Chevrolet Suburban 1G100001 1G174359 1J100010 1J100058 2001 GMC Sierra 1E100003 1E2012022 1F100004 1F113912 1M100023 1M103669 1Z100013 1Z100026.… Read More

Clunk, Bump or Squawk when Vehicle Comes to Complete Stop

Filed Under (Other Manuals) by admin on 02-04-2014

Download 1999-2000 Cadillac Escalade (Old Style) 2002-2004 Cadillac Escalade, Escalade EXT 2003-2004 Cadillac Escalade ESV 1996-1999 Chevrolet 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 Chevrolet 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 Chevrolet Silverado Extended Cab Short Box (New Style) 1999-2004 Chevrolet Silverado 1500 Series Regular Cab (New Style) 2000-2004 Chevrolet 1500 Series Avalanche, Suburban and Tahoe 2001-2004 Chevrolet Silverado 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 Chevrolet Silverado 2500 Series Crew Cab, Short Box (New Style) 1996-1999 GMC 1500 Series Extended Cab Short Box Pickup (Old Style) 1996-1999 GMC 1500 Series Regular Cab Pickup and Utility Models (Old Style) 1999-2002 GMC Sierra Extended Cab Short Box (New Style) 1999-2004 GMC Sierra 1500 Series Regular Cab (New Style) 2000-2004 GMC 1500 Series Yukon, Yukon XL 2001-2004 GMC Sierra 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) 2001-2004 GMC Sierra 2500 Series Crew Cab, Short Box (New Style) 2003-2005 HUMMER H2 with Four Wheel Drive (4WD) or All Wheel Drive (AWD) and One-Piece Propeller Shaft ONLY.… Read More

1995 Mazda MX-6 BRAKE SYSTEM REMOVAL & INSTALLATION

Filed Under (Mazda) by admin on 09-12-2013

Download 1. Raise and support front of vehicle. Remove front wheel assemblies. Remove lower lock pin/guide bolt. See Fig. 2 . Pivot caliper upward and support using rope. 2. Remove pads, shims, guide plates or pad guides and “V” springs (if equipped). Replace pad if lining thickness is less than specified. See MINIMUM PAD LINING SPECIFICATIONS (FRONT) table. 3. To install, reverse removal procedure. Use Disc Brake Expander (49-0221-600C) and an old pad to push piston fully inward to install disc pads. FRONT DISC BRAKE CALIPER Removal & Installation Raise and support front of vehicle. Remove front wheel assemblies and disconnect brake hose. Plug all openings. Remove front disc brake pads. See FRONT DISC BRAKE PADS . Remove remaining mounting bolt(s). Remove caliper from vehicle. To install, reverse removal procedure. Bleed air from system. FRONT BRAKE ROTOR Removal & Installation 1. Raise and support front of vehicle. Remove front wheel assemblies.… Read More

2007 Volkswagen Rabbit Brake pads, removing and installing

Filed Under (Volkswagen (VW)) by admin on 09-12-2013

Download 2007 Volkswagen Rabbit BRAKES Brake System. Brake pads, removing and installing Special tools, testers and auxiliary items required. Brake pads, removing When removing, mark brake pads that will be used again. Install in the same position, otherwise braking effect will be uneven! * Remove wheels. * Disconnect connector – 1 – for brake pad wear indicator. * Remove caps – arrows -. * Loosen both guide pins – arrows – and remove from brake caliper. * Remove brake caliper and secure with wire so that the weight of the brake caliper does not burden or damage the brake hose. * Remove brake pads from brake caliper. Cleaning: * Thoroughly clean contact surfaces for brake pads at brake carrier, remove corrosion. * Clean brake caliper. Use only appropriate solvents for cleaning brake caliper. Brake pads, installing Before pressing piston into cylinder using piston resetting tool, brake fluid must be extracted from brake fluid reservoir.… Read More

2003 Honda Accord LX BRAKES Disc and Drum

Filed Under (Honda) by admin on 01-01-2014

Download Remove wheels. Thoroughly clean outside of caliper to prevent dust and dirt from entering inside. Support caliper with a piece of wire to prevent damage to brake hose. Remove 2 caliper bolts and caliper from bracket. Remove pad shims and pads. Using vernier calipers, measure the thickness of each brake pad lining. Measurement does not include pad backing plate thickness. See DISC BRAKE SPECIFICATIONS . Remove pad retainers. Inspection Clean caliper thoroughly; remove any rust, and check for grooves and cracks. Check brake disc for damage and cracks. Measure brake pad thickness. See DISC BRAKE SPECIFICATIONS . If brake pad thickness is less than service limit, replace pads as a set. Installation 1. Install pad retainers. Apply Molykote M77 compound onto pad side of shim. Wipe excess grease off shim. Keep grease off discs and pads. Install brake pads and shims. Install inner pad with its wear indicator facing downward.… Read More

2007 Ford Focus Accessories List Guide

Filed Under (Ford) by admin on 01-01-2014

Download “Mobile-ease™” Hands Free System Connector Wiring Harness Required for Installation of “Mobile-ease™” Hands Free System 3W4Z-14A411-AA 2005-2007 Hands Free System Requires Connector Harness 14A411 for Installation3W4Z-19G399-AA2005-2007 “Street Appearance Package” ZX3/ZX5 Includes Front & Rear Bumper Fascia & Chromed Exhaust Tip, Primed 6S4Z-6120049-AA 2006-2007 ZX4 Includes Front & Rear Bumper Fascia & Chromed Exhaust Tip, Primed 6S4Z-5420049-BA 2006-2007 Bug Shield Styled Smoke-Color (Single-Pack) 5S4Z-16C900-A 2005-2007 Cargo Area Protector 3-Door/5-Door Black 1M5Z-6111600-AA 2001-2007 Sedan Black 1M5Z-5411600-DA 2001-2007 Wagon Black 1M5Z-7411600-CA 2001-2007 Cargo Logic System Without Logo Sedan, Heathered Black Ink (00) 3M5Z-5411600-AA 2003-2007 3-Door Hatchback, Heathered Black Ink (00) 3M5Z-6111600-AA 2003-2007 Wagon, Heathered Pebble (65) 3M5Z-7411600-AA 2003-2007 Wagon, Heathered Flint (64) 3M5Z-7411600-BA 2003-2007 Wagon, Heathered Black Ink (00) 3M5Z-7411600-CA 2003-2007 Cargo Net, Retention 4-Door/Wagon Envelope Style YS4Z-54550A66-AA 2000-2007 Cargo Organizer 3-Door/5-Door/Sedan Black, For Use Without Subwoofer 5M5Z-54115A00-AAA 2005-2007 Cargo Organizer, Interior Wagon Black, With Ford Logo F8CZ-54115A00-BAA 2000-2007 Cargo Security Shade For Wagon, Med.… Read More

2001 Ford Mustang BRAKES Disc & Drum – Cars – Except Contour, Escort, Focus, LS & Mystique Installation

Filed Under (Ford) by admin on 22-09-2013

Download REAR BRAKE CALIPER CAUTION: Components are not interchangeable from side to side. Disassembly (Continental, Cougar, Mustang, Sable &Taurus) 1. Remove caliper. See REARBRAKE CALIPER &PADS under REMOVAL&INSTALLATION. Mount caliper in a soft-jawed vise. Using Piston Remover/Installer (T87P-2588-A), rotate piston counterclockwise and remove piston from bore. See Fig 13 . Remove dust boot and seal from bore. 2. Carefully remove snap ring, as snap ring and spring cover are under spring load. Remove spring cover, spring, flat washer and key plate. Pull push rod and strut pin from bore. Discard “O”ring from push rod. 3. Remove parking brake lever return spring. Remove lever bolt, and pull lever out of housing. Remove and discard seal. Inspection Clean all metal parts with isopropyl alcohol and dry with compressed air. Replace components if worn, pitted or scored. Reassembly 1. Apply a light coat of Silicone Dielectric Compound (D7AZ-19A331-A) to parking brake lever shaft, bore &seal.… Read More

2004+ Acura TSX Rear Big Brake Kit Installation Instructions

Filed Under (Acura) by admin on 09-12-2013

Download Step 1 Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels Raise Vehicle, and Remove Wheels For a rear kit installation, block the front wheels, and release the parking brake. Then break loose the lug nuts on both rear wheels before jacking up the car. Refer to the Owner’s Manual to identify the correct location of the jack for raising the vehicle. Jack up the vehicle, and secure it on a pair of jack stands, again referring to the Owner’s Manual for jack location joints. After securing the vehicle at a convenient height, remove the rear wheels. Step 2 Disconnect Stock Brake Line Loosen the hard line fitting from the stock brake line, using a 10mm flare wrench. Place a drip tray or several rags directly below the inboard brake line connection. If the area around the brake line connection to the chassis is dirty, clean it using brake cleaner or an appropriate cleaning agent.… Read More

You might also likeclose