diagram on rocker panel on 2002 focus zx3

You search Auto repair manual PDF about diagram on rocker panel on 2002 focus zx3, search results will appear below. If search results do not exist, please search by others keyword.

2000-2002 FORD FOCUS ZX3 AVENGER BODY KIT INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 04-03-2014

Download Cleaning procedure using a paper towel and grease remover or lacquer thinner, thoroughly clean area on car where the double face tape will come in contact with the painted surface. Do not allow thinner or cloth to remain on car too long as it can cause damage to the painted surface. Using either of the recommended adhesion promoters on a clean lint free cloth, apply a thin, uniform coating to the bonding surface, using the minimum amount that will fully coat the surface. Allow promoter to dry completely before attempting installation of the part. 1) front bumper replacement open the hood and remove the factory clips along the center of the factory front bumper. Remove one screw in each wheel well and also remove the two ten millimeter bolts located on the underside of the bumper. Remove the factory front bumper and discard the styrofoam absorber. Remove the grill from the factory bumper and place it on the new wings west front bumper.… Read More

2002 Buick Truck Rendezvous Trim Panel Replacement

Filed Under (Buick) by admin on 13-12-2013

Download Tools Required J 38778 Door Trim Pad and Garnish Clip Remover Removal Procedure 1. Open the door. 2. Disconnect the power window switch assembly. 3. Remove the screws from the front door trim panel 4. Use the J 38778 to remove the trim panel. 1. Reposition the electrical harness connectors. 2. Remove the trim panel from the vehicle. Installation Procedure Important: Before installing the front door trim panel , discard the old trim panel retainers and replace with NEW trim panel retainers. 1. Install the new retainers to the front door trim panel . 2. Route the electrical connectors through the trim panel . 3. Align the trim panel to the door inner panel, guiding the door handle through the trim panel. 4. Install the upper edge of the trim panel to the top edge of the inner door panel, pressing down firmly until the trim panel is fully seated.… Read More

2000-2002 Ford Focus ZX3 Edelbrock Header INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 02-01-2014

Download Disassembly 1. Raise and support the vehicle on a flat stable surface using the floorjack and proper load rated jackstands. 2. Disconnect the battery. 3. Remove three nuts that retain catalytic converter to the stock manifold. 4. Unplug and unclip oxygen sensor wires. There are two sensors; one is located above the catalytic converter, and the second sensor is located below the catalytic converter. The wiring for the lower sensor is clipped to the electric fan bracket. 5. Remove E.G.R. line from catalytic converter. 6. Remove the two bolts retaining the catalytic converter pipe to the intermediate pipe and the two bolts for the catalytic pipe bracket. 7. Remove the two nuts to the catalytic converter retaining bracket and remove the catalytic converter. 8. Remove the dipstick tube, power steering line INSTALLATION INSTRUCTIONS brackets, and the E.G.R. line bracket. Remove the stud from the driver’s side of the cylinder head that was used to hold the power steering line and the E.G.R.… Read More

2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Vehicle Level Body and Frame Interior Moulding / Trim Dashboard / Instrument Panel Service and Repair Instrument Panel (I/P) – Carrier Replacement. REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt.… Read More

FORD RACING M-6564-ALL Roller Rocker Arms Installation INSTRUCTION SHEET

Filed Under (Ford) by admin on 25-02-2014

Download
INSTALLATION INSTRUCTIONS (STUD MOUNTED AND BOLT-ON) : Stud Mounted: Step 1: Rotate engine to number 1 cylinder TDC. Check distributor rotor to make sure it is at the number 1 cylinder terminal. Remove valve covers. Step 2: Remove old rocker arms for number 1 cylinder. If you are converting a pedestal type cylinder head, see the modifications instructions below. Step 3: Oil the pushrod, rocker stud threads, rocker arm and nut. Step 4: Install the new roller rocker arms for number 1 cylinder with the flat area on the trunnion shaft up. Step 5: Make sure the rocker does not bottom on the rocker stud radius. Check clearance through the entire lift range. Check rocker arm geometry. You may need to change pushrod length to achieve proper geometry. Step 6: Also check pushrod guideplate alignment. Some guideplates must be split to allow good pushrod alignment. Step 7: Install the rocker arm nuts and set cold lash/lifter preload.… Read More

FORD FOCUS ZX3 AND ZX5 Vehicle Specific Subwoofer Enclosure Owners manual

Filed Under (Ford) by admin on 29-11-2013

Download The enclosure mounts in the rear drivers’ side, behind back seat firing to the side in the Ford Focus hatchbacks. TOOLS REQUIRED FOR INSTALLATION: Powered Screwdriver #2 Phillips Head Bit 6″ Bit Holder Extension Wire Cutters 5/16″ Wrench Trim Panel Removal Tool INSTALLATION: Follow the steps below 1. Attach the included mounting hardware to your enclosure as shown below. 2. Using the supplied screws, attach the included speaker grill to prevent damage from cargo. 3. Remove floor mat from rear of hatch area. Remove trim screw by the cargo light and place included upper bracket over the hole and replace the screw. 4. If you are using an external amplifier, skip to step 21. 5. Starting at the rear of vehicle, remove plastic trim on drivers’ side. 6. Using furnished wiring harness route 10ga red power wire starting at pre-amp location. Route wire on drivers’ side over to threshold and under carpet to the front of vehicle.… Read More

2008-2011 FORD Focus PART 99-5816 INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 09-12-2013

Download KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision • Painted To Match Factory Dash • A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket • G) (2) Top Clips and (4) Middle Radio Housing Clips Wiring & Antenna Connections (sold seperately) XSVI-5520-NAV – Ford Interface AFSI-02 – if equipped w/ sync 70-5522 – Ford Sub Harness KIT COMPONENTS A TOOLS REQUIRED: Small Flat Blade Screwdriver/ Panel Removal Tool • Phillips Screwdriver • Socket Set • Cutting Tool. 95-5816 DASH DISASSEMBLY. to prevent an accidental short cir- cuit. 1 Unclip and remove the trim panel surrounding the shifter and including the cup holders. (Figure A) Remove (2) 9/32″ screws facing up above the gauge cluster then unclip and remove the trim panel surrounding the gauge cluster.… Read More

2000-2004 Ford Focus ZX3 SVT Suspension Kit INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 17-03-2013

DownloadPARTS IN KIT: ITEM # QTY DESCRIPTION SERVICE PART # REPLACEMENT SOURCE 1 2 Spring, rear 2M5Z-5B669-AA Ford Dealer 2 2 Shock, rear 2M5Z-18125-BA Ford Dealer 3 1 Anti-roll bar, rear 1S4Z-5A772-BA Ford Dealer 4 1 Strut, RF 2M5Z-18124-BA Ford Dealer 5 1 Strut, LF 2M5Z-18124-BB Ford Dealer 6 2 Bump stop 2M5Z-3020-AA Ford Dealer 7 2 Spring, front 2M5Z-5310-AA Ford Dealer 8 2 Nut, upper strut piston W700212-S3091 Ford Dealer. TORQUE SPECIFICATIONS: FASTENER TORQUE (ft./lbs.) (EXCEPT WHERE NOTED) Rear shock upper mount nut 13 Rear shock lower mount nut 85 Rear lower control arm to knuckle 85 Rear anti-roll bar to control arm bolts 11 Rear anti-roll bar bushing clamp bolts 35 Upper strut piston nut 35 Strut tower nuts 18 Knuckle to strut bolt 66 Front anti-roll bar link to strut bolt 94 Caliper to Knuckle 21 Wheel nuts 37. REAR SUSPENSION INSTALLATION INSTRUCTIONS: STEP 1: Raise vehicle off ground and support with jack stands.… Read More

2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module

Filed Under (Acura) by admin on 24-11-2013

Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

2000-UP FORD FOCUS 4 Door Sedan / Wagon, 3 Door Hatchback Audio Installation Instructions

Filed Under (Ford) by admin on 31-12-2013

Download Preliminary: disconnect the negative battery cable. Antenna: the factory antenna is located in the center front of vehicles roof. Radio removal and in-dash installation: note: the factory radio provision is a custom ford double din. When installing an aftermarket din stereo a dash kit is needed. We recommend the scosche fm1375 or fmc1370 installation kit. A set of din removal tools is also needed to remove the factory head unit. We recommend the scosche dt-1 ford din removal tools. 1. Insert ford din removal tools to release clips, pull out stereo, disconnect and remove. Front door speaker installation: note : the factory speaker provision is for a 6 x 8″ speaker. When installing an aftermarket 5 ¼ or 6 ½ speaker, a speaker adapter is required. We recommend the scosche sa68. 1. Extract (7) t-15 torx screws from the perimeter of door panel. 2. Remove screw cover from door opener cup, and extract (1) # 2 philips head screw from behind.… Read More

You might also likeclose