diagram of oxygen sensor location audi a4 1 8t

You search Auto repair manual PDF about diagram of oxygen sensor location audi a4 1 8t, search results will appear below. If search results do not exist, please search by others keyword.

2000 Audi A4 Quattro oxygen sensor Bank 1 sensor 1 malfunction

Filed Under (Audi) by admin on 01-01-2014

Download 2000 Audi A4 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ, USA/Canada 2000 Audi A6 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ Customer Concern: MIL on, DTC P0130 – 16514 – oxygen sensor Bank 1 sensor 1 malfunction; P0150 – 16534 – oxygen sensor Bank 2 sensor 1 malfunction. Engine has extended crank time after sitting for more than a few hours. Tests/Procedures: 1. Trouble Code P0130 (16514) indicates an electrical malfunction with the Bank1, Sensor 1 Oxygen Sensor (O2). Connect a full function Audi compatible scan tool. Enter address menu 01 “Engine Electronics”. Enter functions menu 08 “Read Measuring Value Block”. Enter display group 041. Check specified values in fields 1. Field 1 displays Oxygen Sensor (O2) Bank 1, Sensor 1 (B1S1) heater circuit resistance. Specification is 0.0 to 0.9 Kohm. Note: If the O2′s have not yet reached their operating temperature, there will be no indication in display field 1.… Read More

Audi A4 Bluetooth Hands Free Kit Installation Instruction

Filed Under (Audi) by admin on 13-02-2014

Download Audi A3 (8P) Sportback, Cabrio Audi A4 (8E) B6, B7 Audi A6 (4B)* Audi TT (8J) Roadster, Coupe´ Audi A4 (8K) Audi A5 (8T) Bluetooth Hands Free Kit Installation Instruction. Installation instruction – A3 (8P), A4 (8E), A6 (4B), TT Please remove the head unit using suitable tools, after removing disconnect the necessary wiring. With a plug & play connection you will complete the fitting of the hands free kit. Please see scheme below. Unlock the connection and put the delivered wiring between the head unit and the connector coming from the vehicle. Wire the loom for the interface connection towards the glove box. Find a suitable location for the interface box within the vehicle. Make sure you will reach the interface at any time (regarding to software updates). ATTENTION: Does the vehicle have airbags fitted along the A-column it is essential to wire the loom for the microphone BEHIND the airbag.… Read More

1999-2001 Infiniti Q45 (FY33) MIL “ON” REAR O2 SENSOR DTC

Filed Under (Infiniti) by admin on 10-01-2014

Download 1999-2001 Q45 (FY33) SERVICE INFORMATION If a 1999, 2000, or 2001 Q45 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) • P0158 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Max. Voltage Monitoring) • P0159 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Response Monitoring) • P0160 Heated Oxygen Sensor 2 (Rear) (Bank 2) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies.… Read More

i-R DICE iPod Integration Kit for Audi Radio Interface Kit

Filed Under (Audi) by admin on 21-01-2014

Download Model Supported A3 06+ 1, 2 Symphony I, II Radio A4 98-06 A6 98-04 A8 98-01 S4 98-05 S6/R6 98-04 S8 98-01 Allroad 00-05 i-Audi-R TT 00-06 i-Audi-R 1, 2 1 1 1 1 1 1 1 Symphony I, II Radio Symphony I, II Radio Symphony I, II Radio Symphony I, II Radio Symphony I, II Radio Symphony I, II Radio Symphony I, II Radio Chorus and Concert Radios i-Audi-R i-Audi-R i-Audi-R i-Audi-R i-Audi-R i-Audi-R i-Audi-R. Installation Instructions 1. Pull vehicle into service bay and access trunk area. 2. Disconnect both battery terminals. These cables must be disconnected during installation to insure proper initialization of the DICE module when the DICE when it is connected. 3. Remove radio by inserting the (4) factory keys (not included) into the slots on each corner of the radio. Radio removal keys (not included) 4. CD changer interface will be on left hand side of radio, it is the smaller left-hand connector on the bottom of the harnesses.… Read More

2008 Audi A4 Custom Body Side Molding PART FE-AUDI-A4 INSTALLATION INSTRUCTIONS

Filed Under (Audi) by admin on 01-12-2013

Download FOR: 2008 + Audi A4. PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION 1. LOCATION ( See Diagram below ): Using masking tape, run the tape as seen in Diagram below from POINT A to POINT B. Press tape against the vehicle, making sure that the tape is straight from POINT A to POINT B. 2. CLEAN AND PREP : For proper installation of Custom Body Side Molding, clean the surface where the molding is to be installed using the alcohol pads enclosed. Wipe off excess residue with a clean cloth. Apply PRO- BOND ADHESIVE PROMOTOR in the crush swab self-applicator. Squeeze the applicator until you feel the applicator “crush”. The applicator will become wet on the end and is ready for use. Quickly apply a thin coat of PRO-BOND below the masking tape line, no further than 1 ¼” below the tape. Be careful not to go lower than 1 ¼” because PRO-BOND could dull the paint surface.… Read More

2002-2004 Audi A4 Sedan Radio system General information

Filed Under (Audi) by admin on 30-12-2013

Download Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – Communication. On Board Diagnostic (OBD) Radio systems have extensive On Board Diagnostic (OBD) capabilities. The radio unit has a Diagnostic Trouble Code (DTC) memory. If a malfunction occurs in one of the components or wires which is monitored by the system, a record of the type of malfunction is stored in DTC memory. Use VAS 5051 Vehicle Diagnostic, Testing and Information System in mode “Guided Fault Finding”. Retrofitting of radio systems The electrical connections on the factory- installed radio wiring harness are designed for genuine Audi radios. Radios with different types of electrical connections must be installed using adapter wires. When connecting the vehicle speed sensor signal wire (on radios with the GALA function), take particular care to avoid short circuits, which could result in vehicle malfunctions (e.g. in the engine management system). Vehicle malfunctions may also occur if the vehicle speed sensor signal wire is connected to radios supplied by other manufacturers.… Read More

2005 Audi TT Coupe Sirius or XM Audi Satellite receiver Installation Instructions

Filed Under (Audi) by admin on 09-12-2013

Download Step#01 Make sure ignition keyis removed. Empty trunk of contents. Move luggagecom- partment floor assembly byfolding forward to allow access to the driver’s side fender panel. Step#3A With the 10mm wrench or1/4″ drive ratchet with 10mm universal, remove the first sheet metal screw from the bracket and set it aside. Note: There are two additional fasteners securing the bracket. Step#02 Remove the lamp assemblybyremoving (2) thumb wheel screws. Afterremoval, partiallypull the tail lamp assembly straight back. Upon removal, disconnect wiring harness and set lamp assembly aside in a safe location to prevent damage. Note: Placement of thumbwheel screws: White thumb wheel screw is at the top, the black one is inserted at the bottom. Page 2 of 10 XM orSirius Audi Satellite receiverinstallation Step#03 With the 8mm wrench, remove the alarm horn from the bracket, disconnect the wire harness, and set the screws and horn aside forreinstallation later. Step#3B With the 10mm wrench, remove the second and third 10mm nuts, and set them aside.… Read More

2002-2004 Acura RSX AEM EMS System Installation Instructions

Filed Under (Acura) by admin on 07-02-2014

Download EMS P/N 30-1030 and 30-1030U 2001-2005 Honda Civic 2002-2004 Acura RSX 2002-2004 Honda CR-V. Relocating the Stock ECU 1) Referring to the pictures below, locate the vehicle’s stock ECU. 2) Disconnect the negative battery cable. 3) Disconnect the electrical connectors from the stock ECU. Avoid excessive stress or pulling on the wires, as this may damage the harness. Do not cut any of the wires in the factory harness to remove them. 4) Unscrew all mounting hardware and remove the stock ECU. 5) Relocate the stock ECU in a spot that best suits your needs. Extra Velcro is supplied if needed. Installing the AEM EMS 1) Using the supplied Velcro, secure the EMS in the stock location. 2) This EMS was designed from the USDM Honda/Acura ECU harness. Some non USDM Hondas do not have an immobilizer and their Fuel Pump output is at Pin E10 rather than E1 like the USDM vehicles.… Read More

2001 Infiniti QX4 Direct-Hit – Hotline Archive Detail

Filed Under (Infiniti) by admin on 16-12-2013

Download Vehicle Application: 2001 Infiniti QX4 3.5L, USA/Canada 2002 Nissan Pathfinder 3.5L, USA/Canada 2001 Nissan Pathfinder 3.5L, USA/Canada2003 Infiniti QX4 3.5L, USA/Canada Customer Concern: The check engine light is on with a trouble code P1140. Tests/Procedures: 1. Check the right side (passenger side) Intake Valve Timing Control Position (IVTCP) sensor for 12 volts on the Black/White wire. 2. Check the IVTCP sensor for a good ground on the Black wire. 3. Scope the Yellow/Green signal wire and look for a square wave signal of around 8 volts. Check the pattern of the right side sensor and if unsure of the pattern, compare it to the left bank sensor. Potential Causes: IVTCP Sensor Wiring — IVTCP sensor wiring/connection. Tech Tips: This code is for the right (passenger) bank IVTCP Sensor or sensor circuit. The right and left bank sensors can be swapped from side to side to see if the code will follow the sensor.… Read More

2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR

Filed Under (Ford) by admin on 14-02-2014

Download SELF-DIAGNOSTICS – EEC-V (DIESEL) -2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR. Perform this test when directed by QUICK TEST. This test is intended to diagnose: Exhaust Backpressure (EBP) Sensor • Wiring Harness Circuits (SIG RTN, VREF & EBP Signal) • Powertrain Control Module (PCM) • 1) DTC P0470 This DTC indicates PCM detected EBP sensor malfunction during KOEO ON-DEMAND SELF-TEST. Possible causes for this DTC are: Faulty EBP Sensor • Open Or Shorted Circuit • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. If EBP reading is less than 18.5 psi, clear DTCs. Repeat KOEO ON-DEMAND SELF-TEST . If DTC is still present, replace PCM. If EBP reading is 18.5 psi or more, go to next step. 2) Check Signal Ground Circuit Turn ignition off. Disconnect EBP sensor connector. Sensor is located on top front of engine.… Read More

You might also likeclose