cost to change rear main seal on ford explorer 2000

You search Auto repair manual PDF about cost to change rear main seal on ford explorer 2000, search results will appear below. If search results do not exist, please search by others keyword.

FORD, CHRYSLER, PONTIAC, OLDS WINDAGE TRAY INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 31-12-2013

Download To install studs : Remove a main bolt (main cap can be removed or left in place), tap threads, coat coarse threads with oil, screw stud in by hand, thread 2 main nuts on tray stud and lock them tightly together, lightly tighten tray stud 10-15 ft/lbs (making very sure that double nuts are not slipping or have run into the main cap), remove the 2 main nuts, coat the fine threads with oil, install the stud washer and nut, torque main stud with oil to torque spec of 65 ft/lbs for 7/16″ or 85 ft/lbs for 1/2″ studs, install 1 silver tray adjusting nut on the 3/8″ fine thread with the serrated face towards you (away from the engine). Do all the required studs locations to mount the tray in this fashion. You are now ready to mount the tray assembly. To install tray : Once all necessary tray studs have been installed properly, consult the special considerations section for the initial tray height and correct width, adjust the tray nut to this height, slide tray assembly into place and onto mounting studs, make sure that tray is supported equally by all studs (no wobble), the install the 2nd silver tray nut with the serrations toward the tray and torque with oil to 35 ft/lbs.… Read More

1996-2000 Honda Civic Rear Main Oil Seal Leaks

Filed Under (Honda) by admin on 09-12-2013

Download 1996-00 Civic – ALL 2001 Civic – See VEHICLES AFFECTED Civic Rear Main Oil Seal Leaks (Supersedes 01-040, 1996 – 2001 Civic Rear Main Seal Leak , dated June 12, 2001) SYMPTOM The engine leaks oil between the block and the transmission. PROBABLE CAUSE The rear main oil seal (crankshaft oil seal) is contaminated. REPAIR PROCEDURE 1. Remove the transmission. Refer to section 13 or 14 of the appropriate service manual. 2. Remove and discard the rear main oil seal (crankshaft oil seal). 3. Install the new oil seal. Refer to page 7 – 29 of the ’96-00 service manual or page 7-27 of the ’01 service manual. 4. Reinstall the transmission. 5. Reinstall the drain plug with a new sealing washer. 6. Refill the transmission with the appropriate fluid. 7. 2001 models only. Do the idle learn procedure: Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off, then start the engine.… Read More

2000 Ford F-150 Rear Drive Axle/Differential

Filed Under (Ford) by admin on 01-01-2014

Download 1. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the RH kick panel area. Failure to do so can result in unexpected inflation or deflation of the air springs, which can result in shifting of the vehicle during these operations. Raise and support the vehicle. 2. Remove the wheel and tire assembly. 3. Remove the differential housing cover (4033). ? Drain the lubricant. For additional information, refer to Differential Housing Cover in this section. 4. Remove the brake calipers and discs. 5. Remove the differential pinion shaft (4211). 1. Remove and discard the differential pinion shaft lock bolt. 2. Remove the differential pinion shaft. 6. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers (4N237). 1.… Read More

1998 – 2001 Ford Explorer 4WD Ford Ranger Explorer Sport Trac / Edge Mountaineer 4WD Torsion bar key front leveling kit

Filed Under (Ford) by admin on 15-02-2014

Download Part # 22907 1998 – 2001 Ford Explorer 4WD 1998 – 2007 Ford Ranger / Explorer Sport Trac Edge / Mountaineer 4WD Torsion bar key front leveling kit Part# Description Qty. 22907-01 Torsion bar keys 2 22907INST Instruction manual (customer copy) 1 22907INST Instruction manual (installer copy) 1 WARNINGDECAL Warning decal 1 MIRRORHANGER Rear view mirror hanger 1. Important customer information: Tuff Country EZ-Ride Suspension highly recommends that a qualified and/or certified mechanic performs this installation. If you desire to return your vehicle to stock, it is the customers responsibility to save all stock hardware. This vehicles reaction and handling characteristics may differ from standard cars and/or trucks. Modifications to improve and/or enhance off road performance may raise the intended center of gravity. Extreme caution must be utilized when encountering driving conditions which may cause vehicle imbalance or loss of control. DRIVE SAFELY! Avoid abrupt maneuvers, such as sudden sharp turns which could cause a roll over, resulting in serious injury or death.… Read More

1990 – 1995 Ford Taurus Mercury Sable Radio Replacement Installation Instructions

Filed Under (Ford) by admin on 02-01-2014

Download Remove Factory Radio STEP 1 : The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio. This vehicle may have the Ford Premium Sound System installed in the vehicle. When you pull the Ford radio out of the dash, there may be a square connector plugged into the rear of the Ford radio. If there is a square plug, then your vehicle has amplifiers.… Read More

2000-2004 Ford Focus ZX3 SVT Suspension Kit INSTALLATION INSTRUCTIONS

Filed Under (Ford) by admin on 17-03-2013

DownloadPARTS IN KIT: ITEM # QTY DESCRIPTION SERVICE PART # REPLACEMENT SOURCE 1 2 Spring, rear 2M5Z-5B669-AA Ford Dealer 2 2 Shock, rear 2M5Z-18125-BA Ford Dealer 3 1 Anti-roll bar, rear 1S4Z-5A772-BA Ford Dealer 4 1 Strut, RF 2M5Z-18124-BA Ford Dealer 5 1 Strut, LF 2M5Z-18124-BB Ford Dealer 6 2 Bump stop 2M5Z-3020-AA Ford Dealer 7 2 Spring, front 2M5Z-5310-AA Ford Dealer 8 2 Nut, upper strut piston W700212-S3091 Ford Dealer. TORQUE SPECIFICATIONS: FASTENER TORQUE (ft./lbs.) (EXCEPT WHERE NOTED) Rear shock upper mount nut 13 Rear shock lower mount nut 85 Rear lower control arm to knuckle 85 Rear anti-roll bar to control arm bolts 11 Rear anti-roll bar bushing clamp bolts 35 Upper strut piston nut 35 Strut tower nuts 18 Knuckle to strut bolt 66 Front anti-roll bar link to strut bolt 94 Caliper to Knuckle 21 Wheel nuts 37. REAR SUSPENSION INSTALLATION INSTRUCTIONS: STEP 1: Raise vehicle off ground and support with jack stands.… Read More

1997 F150 – Ford Expedition Radio Replacement Installation Instructions

Filed Under (Ford) by admin on 24-11-2013

Download Parts REQUIRED for the install Description Snap on in dash wire harness ** Please read instructions first Radio dash installation kit 1999 Ford F150/Expedition kit Optional parts for this install None. Remove Factory Radio STEP 1 : The plastic dash panel surrounding the radio must be removed. This dash panel simply unsnaps by pulling. With your hands, grab one corner and pull until the plastic dash panel completely pulls away from the main body of the dash. The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a ‘U’ shape. For more information on how to remove the radio, see the diagram below. STEP 2 : Pull the radio from the dash.… Read More

Ford Super Duty 4×4 Mag Hytec Rear Diff Cover Install and Rear Diff Gear Oil Change 2004 F250 4×4 XLT Sport Crew Cab

Filed Under (Ford) by admin on 17-02-2014

Download TOOLS & PARTS I USED – Mag-Hytec Ford 10.5 rear differential cover – Redline #57914 75W140 gear oil, 6 quarts – 1/2″ socket & ratchet (cover bolt removal) – Flat screwdriver – Torque wrench – Drain pan – Several rags – Plastic putty paddle – Small funnel – Lacquer thinner – 1/4″ allen wrench (new cover bolt install) PROCEDURE Here’s a few pics of the Mag Hytec cover. Its a very impressive cover, complete with additional oil capacity, a magnetic dipstick, a drain plug, a 1/8 NPT port (for a temperature sending unit), and an o-ring to seal to the rear diff case. Here’s a shot of the dipstick (left) and temperature sender port. Here’s a pic of the drain plug on the bottom. Dipstick removed
Drain plug removed Here’s the stainless hardware that’s included with the cover. They also include the two sizes of allen wrenches needed for the installation of the bolts and to service the drain plug/diptstick/sender port.… Read More

Ford Mustang Fuel Injection Conversion

Filed Under (Ford) by admin on 04-05-2012

Download These instructions will provide the basic and necessary information to allow a carbureted 302 to be converted to SEFI Fuel Injection. There are several different types of fuel injection conversions available, however, this instruction will concentrate on the High Output, MASS-AIR setups found on the 92-93 Ford Mustangs. There are two main advantages to using this type of setup. The first advantage is that the computer in the MASS-AIR system will automatically compensate for any engine modifications that have been done prior to the installation of the fuel injection system. The second advantage is that fuel is sent to each cylinder individually only during the appropriate firing cycle, meaning that fuel is sent sequentially to each cylinder only when the spark plug is ready to fire. This makes for an extremely efficient firing cycle . SEFI stands for Sequential Electronic Fuel Injection. This system is complex to be sure, therefore, this instruction is going to skip all the technical mumbo-jumbo, and focus on the bare essentials to install this system properly.… Read More

Torque Converter Oil Seal Installation Tool

Filed Under (Other Manuals) by admin on 31-03-2014

Download Applies To: All ModelsWith L4 or V6 Engine and A/TWith 44 mm I.D. Torque Converter Oil Seal Torque Converter Oil Seal Installation Tool The service manual procedure for installing the torque converter oil seal requires you to disassemble the transmission. Anew required special tool, which attaches to your existing 40 mm I.D. driver, lets you install this seal without removing the main shaft or disassembling the transmission. REQUIRED SPECIAL TOOLS Seal DriverAttachment: T/N 07XAD-001000A (Shippedtoall dealers March 2000 as a required special tool) 40 mmI.D. Driver: T/N 07746-0030100 ORDERING INFORMATION Additional seal driver attachments are available from American Honda using normal parts ordering procedures. WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. PROCEDURE 1. Remove the transmission (see section 14 of the appropriate service manual). 2. Remove and discard the torque converter oil seal. Be careful not to damage the torque converter housing. 3. Select the appropriate replacement seal.… Read More

You might also likeclose