2003 Chevy Truck TrailBlazer Cooling System-Electro-Viscous Fan Clutch Operation

Download 2003 Chevy Truck TrailBlazer 2WD L6-4.2L VIN S Cooling System – Electro-Viscous Fan Clutch Operation. Subject: Operating Characteristics of the Electro-Viscous (EV) Fan Clutch and Diagnostic Tips for Cooling Fan Noise, Delayed Transmission Shifts and/or Engine Revving Too High Models: 2004-2006 Buick Rainier 2002-2006 Chevrolet TrailBlazer, TrailBlazer EXT 2006 Chevrolet TrailBlazer SS 2002-2006 GMC Envoy, Envoy XL 2004-2005 GMC Envoy XUV 2002-2004 Oldsmobile Bravada 2005-2006 Saab 9-7X with 4.2L I-6, 5.3L V-8 or 6.0L V-8 Engine (VINs S, P, M, H – RPOs LL8, LM4, LH6, LS2) Date/VIN Breakpoints for Vehicles with New EV Fan Clutch. Vehicles built after and including the Date or VIN Breakpoints listed in the table shown are equipped with the new electro-viscous (EV) fan clutch . Vehicles of any model year listed in “Models Affected” with labor code J3390 (claimed after June 8, 2005) with P/N 15293048 in Claim History may also be equipped with this new EV fan clutch .… Read More

2002 Ford Escort Cooling System Draining, Filling and Bleeding Workshop Manual

Download Draining 1. Bring the engine to normal operating temperature and turn the engine off. With the cooling system under pressure, inspect cooling system hoses and clamped hose connections for leaks, excessive deterioration or contact wear. Inspect radiator installation retention. Note any discrepancies and proceed. 2. WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap.… Read More

2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module

Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

2002 Pontiac Grand Prix GT THERMOSTAT REPLACEMENT

Download 2002 Pontiac Grand Prix GT 2002 ENGINE Engine Cooling – Grand Prix THERMOSTAT REPLACEMENT (3.1 L) Tools Required J 38185 Hose Clamp Pliers Removal Procedure 1. Remove the air cleaner intake duct. Refer to AIR CLEANER INTAKE DUCT . 2. Partially drain the cooling system. Refer to Draining and Filling Cooling System . 3. Use the J 38185 in order reposition the hose clamp from the water outlet housing. 4. Remove the radiator inlet hose from the water outlet housing. 5. Remove the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) 6. Remove the water outlet housing bolts. 7. Remove the water outlet housing and gasket. 8. Remove the thermostat. 9. Clean the water outlet housing mating surfaces. Installation Procedure 1. Install the thermostat. 2. Install the water outlet gasket and the water outlet housing. 3. Install the water outlet housing bolts.… Read More

2002-2003 Acura RSX Icebox Cold Air Intake Installation Instructions

Download Honda Civic Si & Acura RSX Icebox Cold Air Intake Installation Instructions (2002-2003 Honda Civic Si) (2002-2003 Acura RSX—All) Step #1 Remove Stock Airbox • Before disconnecting battery locate radio code to reactivate radio after installation. (write down preset channels for later use) •Disconnect Negative battery terminal. •Remove battery positive terminal, tie down clamp, battery and plastic tray. •Remove engine cover around throttle body on intake manifold (A). •Remove stock air box lid and filter. •Disconnect Intake Air Temperature (IAT) sensor, remove upper intake hose and clamps (B). •Remove air box mounting bolts and nut. Rotate air box forward and out. Remove rubber grommets and stepped bushings from stock air box*. •Remove Lower Air inlet hose by removing mounting bolt from radiator cross support above cooling fan. •Remove ground strap bracket on side of transmission (C). Relocate ground strap from transmission bracket to top of transmission (D). Step #2 Install Comptech Airbox •Install (3) stock rubber grommets* (E) through large holes on underside of mounting ears on Icebox (a small dab of filter oil may be used to ease this process).… Read More

2002 Acura RSX 555I Honda/Acura Immobilizer Bypass Module

Download Honda Civic 2001-2002 Acura RSX 2002. Installation Instructions 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the wiring color guide. 3. Wire the 555I as shown in the wiring diagram. IMMOBILIZER IGNITION FEEDYELLOW/BLACK DATA RED/BLUE KEY SENSE RED/WHITE RED: Connect this wire to a constant (+)12 volt source. BLACK: Connect this wire to a quality chassis ground (preferably scraped sheet metal) separate from other component ground locations. BLUE: Connect this wire to the BLUE status output of the remote start. It must see ground during remote start. BLUE/WHITE: Connect this wire to the (-) key sense wire listed in the Wire Color Guide. It is located in a six-pin molex at the ignition cylinder. The key sense wire rests at ground when the key is inserted into the ignition switch.… Read More

2002 PEUGEOT 406 SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS

Download
ALARM/SIREN POSITION Position the compact alarms and the sirens on the dome of the shock absorber, passenger’s side. CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard, driver’s side. POWER SUPPLY + 30: connect to the 3 mm2 RED wire located at the entrance of the fuse box. – 31: connect to one of the original ground terminals located on the right of the BSI operating central.. IGNITION WIRE + 15/54: connect to the wire at the position nr. 16 coming out of the 26 way blue connector of the BSI operating central. DIRECTION INDICATORS Connect to the wires at the positions nr. 13 and nr. 14 of the 16 way black connector coming out of the BSI operating central. ELECTRIC WINDOWS Positive control signal Front window, driver’s side: Refer to the diagram nr. 114. Front window, passenger’s side: Cut the 1 mm2 GREY wire located at the position nr.… Read More

555H Honda/Acura Immobilizer Bypass Module Manual Installation Instructions

Download
Models : Honda Accord: 1999-2002 Honda Odyssey: 1999-2002 Honda Prelude 1999 Acura CL 2001-2002 Acura Integra: 2001-2002 Acura MDX: 2001-2002 Acura TL: 2001-2002.
Product Description : The Honda/Acura Immobilizer anti-theft system uses a low-power transponder mounted in the head of the ignition key. When the vehicle is started, the Key Cylinder Module converts the transponder signal and sends a secure, coded signal to the Engine Control Module. If the signal to the Engine Control Module is correct, the vehicle will start.
Installation Instructions : 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide . 3. Wire the 555H as shown in the wiring diagram.
Wire Connection Guide : BLUE/WHITE: Connect this wire to the (-) key sense wire at the ignition cylinder.… Read More

556H Honda / Acura Immobilizer Bypass Module Installation Instruction

Download Mode 1 Mode 2 ? Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 2002-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More

555H Honda/Acura Immobilizer Bypass Module

Download Models Honda Accord: 1999-2002 Honda Odyssey: 1999-2002 Honda Prelude 1999 Acura CL 2001-2002 Acura Integra: 2001-2002 Acura MDX: 2001-2002 Acura TL: 2001-2002. Installation Instructions 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide . 3. Wire the 555H as shown in the wiring diagram. Wire Color Guide SYNCH BLUE, ORANGE/BLUE, or BLUE/WHITE DATA RED OR BLUE/GREEN KEY SENSE BLUE/WHITE. Wire Connection Guide BLUE/WHITE: Connect this wire to the (-) key sense wire at the ignition cylinder. The key sense wire rests at ground when the key is inserted into the ignition switch. BLACK: Connect this wire to a quality chassis ground (preferably scraped sheet metal) separate from other component ground locations. BLUE: Connect this wire to the BLUE status output of the remote start.… Read More