como quitar engine light de winstar 1999

You search Auto repair manual PDF about como quitar engine light de winstar 1999, search results will appear below. If search results do not exist, please search by others keyword.

1999 Saturn SL Engine – Driveability Concerns/Cooling System DTC’s Set

Filed Under (Saturn) by admin on 24-02-2014

Download 1999 Saturn SL1 L4-1.9L SOHC VIN 8 Vehicle Level Powertrain Management Computers and Control Systems Coolant Temperature Sensor/Switch (For Computer) Technical Service Bulletins All Technical Service Bulletins Engine – Driveability Concerns/Cooling System DTC’s Set. SUBJECT: Engine Coolant Temperature Sensor Related Diagnostic Trouble Code(s) and/or the Following Conditions: Hard Start, Erratic Idle, Rough Running. Engine Overheating, Low and/or Leaking Coolant, and/or Service Engine Soon Lamp Illuminated. (Replace Engine Coolant Temperature Sensor with New Design Sensor- P/N 21025106) MODELS AFFECTED: 1991-2001 Saturn S-Series vehicles CONDITION: Customers may comment about various driveability and/or engine operating concerns including: hard start, erratic idle, rough running, engine overheating, low and/or leaking coolant, and/or Service Engine Soon lamp illuminated. CAUSE: This condition may be caused by a cracked engine coolant temperature sensor. CORRECTION: Replace engine coolant temperature sensor, inspect and if necessary replace sensor harness connector. Refer to procedure in this bulletin to replace engine coolant temperature sensor and Parts Requirements for specific parts information.… Read More

1999 Chevrolet Suburban C1500 Engine Misfire MIL/SES Light Illuminated or Flashing

Filed Under (Chevrolet (Chevy)) by admin on 01-01-2014

Download Information on Engine Misfire MIL/SES Light Illuminated or Flashing DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0420 or P0430. SERVICE INFORMATION If you encounter vehicles that exhibit the above conditions, refer to SI for the appropriate DTC(s) set. If no trouble is found, the cause may be due to an ECM ground terminal that has corroded with rust over time. Inspect the main engine wiring harness ground terminal (G103) for this condition. The wire terminal (G103) attaches either to the front or to the rear of the right side cylinder head, depending on the model year of the Full Size Pickup and/or Utility Trucks. If the ECM ground terminal has been found to be corroded, then follow the service procedure outlined in this bulletin to correct the corrosion issue. Fig. 2: Engine Wiring Harness Ground Terminal Location (1999-2006 Full Size Pickup and/or Utility Trucks) Courtesy of GENERAL MOTORS CORP.… Read More

1998 Chevrolet Blazer Engine Oil Cooler Hose/Pipe Replacement

Filed Under (Chevrolet (Chevy)) by admin on 12-03-2014

Download 1998 Chevrolet Blazer – 4WD | Blazer, Bravada, Jimmy, S10 Pickup, ┬áSonoma (VIN S/T) Service Manual | Engine | Engine Mechanical – 4.3L | Repair Instructions. Engine Oil Cooler Hose/Pipe Replacement (4WD) Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6.… Read More

1999-2000 Ford Windstar The battery light is on, but the alternator is charging Has a code P1246

Filed Under (Ford) by admin on 18-01-2014

Download Direct-Hit 2000 Ford Windstar 3.8L Test Details Hotline Archive # 124501 Confirmed Fix Vehicle Application: 1999 Ford Windstar 3.8L, Vin 4 2003 Ford Windstar 3.8L 2000 Ford Windstar 3.8L, Vin 4 Customer Concern: The battery light is on, but the alternator is charging. Has a code P1246. Tests/Procedures: 1. Disconnect the alternator and the Powertrain Control Module (PCM). Check the Violet (VT) (GENerator MONitor or GENMON) wire from the alternator to pin 20 of the PCM connector and the Red/Pink (RD/PK) (GENerator COMmand or GENCOM) wire from the alternator to pin 45 of the PCM for high resistance, an open, or a short to ground. Repair the wiring as needed. 2. If the wiring checks OK, reconnect the PCM and alternator. Start the engine and monitor the VT wire for a roughly 0-10v square wave signal. The signal will be around 40-50% normally with no loads on the system and minimal charging system output.… Read More

2000 Buick Regal Oil Pan Replacement

Filed Under (Buick) by admin on 02-01-2014

Download Tools Required z J 28467-90A Engine Support Adapters z J 28467-B Universal Engine Support Fixture z J 36462-A Engine Support Adapter Leg Set 1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical. 2. Carefully disconnect the throttle body air inlet duct. 3. Remove the engine mount struts from the engine. Refer to Engine Mount Strut Replacement . 4. Remove the drive belt. Refer to Drive Belt Replacement . 5. Install the J 28467-90A , the J 28467-B and the J 36462-A . Do not raise the engine. Refer to Engine Support Fixture . 6. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 7. Disconnect the three-way catalytic converter pipe from the right exhaust manifold. Refer to Catalytic Converter Replacement in Engine Exhaust. 8. Remove the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.… Read More

Ford Mustang Fuel Injection Conversion

Filed Under (Ford) by admin on 04-05-2012

Download These instructions will provide the basic and necessary information to allow a carbureted 302 to be converted to SEFI Fuel Injection. There are several different types of fuel injection conversions available, however, this instruction will concentrate on the High Output, MASS-AIR setups found on the 92-93 Ford Mustangs. There are two main advantages to using this type of setup. The first advantage is that the computer in the MASS-AIR system will automatically compensate for any engine modifications that have been done prior to the installation of the fuel injection system. The second advantage is that fuel is sent to each cylinder individually only during the appropriate firing cycle, meaning that fuel is sent sequentially to each cylinder only when the spark plug is ready to fire. This makes for an extremely efficient firing cycle . SEFI stands for Sequential Electronic Fuel Injection. This system is complex to be sure, therefore, this instruction is going to skip all the technical mumbo-jumbo, and focus on the bare essentials to install this system properly.… Read More

1998 Buick Park Avenue Engine Coolant Consumption or Coolant Leak

Filed Under (Buick) by admin on 20-01-2014

Download Engine Coolant Consumption or Coolant Leak (Inspect For Material Degradation/Replace Intake Manifolds) Models: 1995-1997 Buick Riviera 1995-1999 Buick LeSabre, Park Avenue 1996-1999 Buick Regal 1998-1999 Chevrolet Lumina, Monte Carlo 1995-1996 Oldsmobile Ninety-Eight 1995-1999 Oldsmobile Eighty-Eight 1998-1999 Oldsmobile Intrigue 1995-1999 Pontiac Bonneville 1997-1999 Pontiac Grand Prix with 3.8L Engine (VIN K — RPO L36) Condition Some customers may comment on excessive engine coolant consumption, or an engine coolant leak near or under the throttle body area of the upper intake manifold. Cause Upper intake manifold composite material may degrade around the EGR stove pipe and could result in an internal or external coolant leak. Correction 1. Follow the upper intake manifold removal instructions found in the Engine Unit Repair Section of the Service Information Manual. 2. Refer to the arrow in the illustration of the upper intake manifold above. Inspect the inner diameter of the EGR passage for signs of material degradation.… Read More

1998 Chrysler Town & Country LX SERPENTINE BELT SLIPS OFF IDLER PULLEY

Filed Under (Chrysler) by admin on 09-12-2013

DownloadModel(s): 1996-1999 Chrysler (NS) Town & Country 1996-1999 Dodge (NS) Caravan 1996-1999 Plymouth (NS) Voyager 1996-1999 Chrysler (GS) Voyager (International Market) Group: Cooling Bulletin No.: 07-02-99 Date: June 4, 1999 OVERVIEW This bulletin involves replacing the bracket that the idler pulley attaches to. SYMPTOM/CONDITION Loss of power steering assist and occurs when driving through deep snow or standing water. Snow or rain can enter the engine compartment from underneath the vehicle and force the serpentine belt off of the idler pulley. DIAGNOSIS Visually inspect the serpentine belt and idler pulley to determine if mis-alignment exists (If the serpentine belt is off the pulleys install the serpentine belt). Start the engine and let it run for one minute before checking alignment). The belt should be approximately 2mm (0.08 in.) from the inboard edge of the idler pulley ( Fig. 1 ) when alignment is correct and this bulletin does not apply. If the belt and pulley appear as in Fig.… Read More

1999 Ford Contour/Mystique Timing Belt Workshop Manual

Filed Under (Ford) by admin on 01-01-2014

Download 1. CAUTION: The maximum amount by which the engine management system will adjust the camshaft timing (VCT control unit) is limited to two degrees. As a result of this an extremely high degree of accuracy is required for any work which affects the valve timing. NOTE: The locations of engine mountings and engine support insulators are described looking from the transaxle to the engine. NOTE: Operation steps which only apply to certain model variants and therefore do not apply to all vehicles are clearly marked. Disconnect the battery ground cable. 2. Raise and support the vehicle. For additional information, refer to Section 100-02 . 3. Loosen the right-hand front wheel nuts. 4. Remove the right-hand front wheel. 5. Remove the engine underschield (if equipped). 6. Remove the right-hand front splash shield. 7. NOTE: Mark the accessory drive belt direction if the belt is to be reused. Remove the accessory drive belt.… Read More

2003 BMW 325I Sport Wagon Check engine light on and fault codes stored

Filed Under (BMW) by admin on 19-03-2014

Download 2002 BMW 325I 2.5L 2003 BMW 325I Sport Wagon 2.5L, Eng Des M54, USA Customer Concern: Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible.… Read More

You might also likeclose