". You can read and download the PDF file on this page, or you can watch the video tutorial. Please use another keyword if these document aren't what you look for.
wiring diagram for brake switch connector for a 1998 chevy silverado.
Question - 1998 chevy blazer: diagram..front windshield wiper motor - KG. Find the answer to this and other Chevy questions on JustAnswer..
turn signal wiring 95 k1500 Electrical Thanks to all for the advise and for the schematics. now I'm sure I can get this working..
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 09-12-2013
Download Removal Procedure 1. Disable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR. 2. Remove the upper and lower trim covers. Refer to Steering Column Trim Covers Replacement . 3. Remove the wire harness assembly (1) from the wire harness strap (2). 4. Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector. Fig. 29: Turn Signal & Multifunction Switch Assembly Connectors Courtesy of GENERAL MOTORS CORP. 5. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly out of the bulkhead connector (1). 6. Remove the 2 pan head tapping screws (1) and (3) from the turn signal and multifunction switch assembly (2). 7. Remove the turn signal and multifunction switch assembly (2) from the steering column tilt head assembly. Installation Procedure 1. Install the turn signal and multifunction switch assembly (2) onto the steering column tilt head assembly.… Read More
Download 2003 Chevrolet Impala LS MULTIFUNCTION, TURN SIGNAL SWITCH REPLACEMENT
Filed Under (Volkswagen (VW)) by Doe Namblas on 02-01-2014
Download Steering column, assembly WARNING:Special safety precautions and some different procedures apply to vehicles equipped with airbags CAUTION:Before working on the electrical system: Obtain radio anti-theft code. Ignition OFF ! Disconnect battery Ground (GND) strap. Note: After reconnecting battery: Activate vehicle equipment such as radio, clock and power windows as per service procedures and/or Owner’s Manual. On vehicles equipped with OBD II, activate readiness code. Refer to Powertrain Management, Computers and Control Systems, Testing and Inspection, Procedures See: Powertrain Management/Computers and Control Systems/Testing and Inspection For further information on the steering column assembly, refer to Steering and Suspension, Steering, Steering Column, Service and Repair. 1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig.… Read More
Download 2000 Volkswagen Cabrio Ignition Switch: Service and Repair
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 02-12-2013
Download 1989 Chevrolet Corvette V8-350 5.7L Steering Column: Service and Repair Disassembly/Assembly SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE Disassembly 1. Remove steering wheel as follows: a. Disconnect battery ground cable, then remove horn cap from steering wheel by pulling. b. Disconnect horn button wire, then remove telescope lever screws and shaft lock knob screw. c. Remove telescope adjustment lever, steering wheel nut retainer and nut. d. Remove steering wheel with a puller. 2. Remove spacer, bumper, spacer and snap ring retainer (Nos. 2, 3, 4, and 5 in Fig. 59 ). 3. Remove shaft lock retainer using lock plate compressor to depress shaft lock. 4. Remove shaft lock and carrier assembly, upper bearing spring, upper bearing seat and inner race. 5. Reverse procedure to install. TURN SIGNAL SWITCH Disassembly 1. Remove SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE as previously outlined.… Read More
Download 1989 Chevrolet Corvette Steering Column: Service and Repair
Filed Under (Honda) by Doe Namblas on 24-01-2014
TURN SIGNAL RELOCATION 1. Refer to Figure 2. Remove seat.
SAFETY: DISCONNECT BATTERY PRIOR TO ALL WIRING MODIFICATIONS 2. Disconnect wires to turn signals and taillights under seat. 3. Remove three bolts on each side that secures fender to strut. 4. Lower fender onto tire and remove. 5. Remove turn signals from fender strut. Observe and mark “left” and “right” for re-installation. 6. Cut each turn signal wire 3″ from connector end and splice 24″ of electrical wire. Turn signal bracket must be oriented forward (ears of bracket to the front). 7. Remove license plate light mounting bolts. Remove grommet. Route turn signal wires through empty grommet hole, Refer to inset in figure 2, route wire past the taillight and through the existing hole in the fender. Using the wire clamp on the right side taillight bolt. Secure wire to taillight wire with the supplied tie wraps. 8. Install turn signal bracket between license plate and license plate bracket using 1/4-20 x 1 1/4″ Hex Cap Screw, 1/4″ flat washer, 1/4″ x 1″ flat washer, and 1/4″ nut.… Read More
Download Honda Aero Shadow 750 MODEL 334/S334 Manual Installation Instructions
Filed Under (Chevrolet (Chevy)) by Doe Namblas on 10-12-2013
Download1988-94 Models See Figures 1 and 2 Remove the steering wheel. 1. Fig. Fig. 1: Installing the lock cylinder. Fig. Fig. 2: Ignition switch Remove the turn signal switch. It is not necessary to completely remove the switch from the column. Pull the switch rearward far enough to slip it over the end of the shaft, but do not pull the harness out of the column. 2. Turn the lock to Run. 3. If necessary, remove the ignition key. 4. If equipped, remove the buzzer switch assembly. 5. Remove the lock retaining screw and remove the lock cylinder. 6. WARNING If the retaining screw is dropped on removal, it may fall into the column, requiring complete disassembly of the column to retrieve the screw. To install: Rotate the key to the stop while holding onto the cylinder. 7. Push the lock all the way in. 8. Install the screw. Tighten the screw to 40 inch lbs.… Read More
Download 1998 Chevrolet Truck C1500 Repair Information
Filed Under (Ford) by Doe Namblas on 31-12-2013
Download 1993 Ford Escort G – TESTS W/CODES – EEC-IV (1.9L)’ ’1993 ENGINE PERFORMANCE Ford Motor Co. – Self-Diagnostics – EEC-IV. CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH) Diagnostic Aids When ignition switch is in the ON or START position, the PCM connects FUEL PUMP circuit (PCM terminal No. 22) to ground. The fuel pump relay is energized and electrical current flows to the fuel pump. If PCM does not receive ignition PIP signal within 2 seconds, FUEL PUMP circuit is opened and fuel pump operation is terminated. Perform this test when instructed by QUICK TEST or CIRCUIT TEST AA. This test is only intended to diagnose: * Fuel pump relay. * Inertia Fuel Shutoff (IFS) switch. * Wiring harness circuits (B+, VPWR, FUEL PUMP, GND and POWER-TO-PUMP). * Faulty Powertrain Control Module (PCM). Fig. 31: Fuel Pump Monitor Circuit Diagram (Escort & Tracer) 1)Code 87/556: Check VPWR To Fuel Pump Relay Code 87/556 indicates a fuel pump primary circuit failure.… Read More
Download 1993 Ford Escort FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH)
Filed Under (Cadillac) by Doe Namblas on 06-04-2014
Download . Circuit Description The torque converter clutch (TCC) brake switch is used to indicate the status of the brake pedal (applied or released). If the PCM detects an open TCC brake switch (stuck ON) during accelerations, then DTC P0719 sets. DTC P0719 is a type C DTC. Conditions for Running the DTC * No VSS DTCs P0502 or P0503. * DTC P0719 has not passed this ignition cycle. Conditions for Setting the DTC The TCC brake switch input is at 0 volts for 15 minutes and the following conditions occur 8 times without a status change on the TCC brake input: * The vehicle speed is less than 8 km/h (5 mph). * The vehicle accelerates to 32 km/h (20 mph) within 2-6 seconds. * Then the vehicle speed remains above 32 km/h (20 mph) for 6 seconds. Action Taken When the DTC Sets * The PCM does not illuminate the malfunction indicator lamp (MIL).… Read More
Download 2000 Cadillac DeVille Brake Switch Circuit Low Input
Filed Under (Honda) by Doe Namblas on 27-02-2014
ALARM/SIREN POSITION Position the compact alarms and the sirens in the engine compartment, under the battery support.
CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard on the drivers side.
POWER SUPPLY + 30: connect to the free faston at position 5 on the front part of the fuse box. – 31: connect with a ring terminal to one of the terminals coming out of the original power supply on the left lateral side, drivers side.
IGNITION WIRE + 15/54: connect to the YELLOW/BLACK wire of the 6 way brown connector of the fuse box.
DIRECTION INDICATORS Connect to the 1,5 mm2 GREEN/BLUE and YELLOW/GREEN wire located in the 20 way green connector at the centre of the fuse box.
CENTRAL DOORS LOCKING See diagram nr. 60 for antithefts of the Bridge serie and diagram nr. 60A for antithefts of the 3100 serie.
IMMOBILISATION POINT Fuel pump Cut the 1,5 mm2 YELLOW/GREEN wire located in the brown connector which works as a support to the grey relay of the fuel pump located to the left of the fuse box.… Read More
Download 1997 Honda Civic Alarms Fitting Wiring Diagram Manual Instructions
Filed Under (Acura) by Doe Namblas on 24-11-2013
Download Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 20026? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. Installation Instructions 1. Remov-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ?? steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More
Download 2000-2002 Acura Integra 556H Honda/Acura Immobilizer Bypass Module
Filed Under (Honda) by Doe Namblas on 29-01-2014
Download Mode 1 Mode 2 ? Honda Accord 2003-2004 ? Honda Accord 1998-2002 ? Honda CRV 2002-2004 ? Honda CRV 1998-2001 ? Honda Civic 2001-2004 ? Honda Odyssey 1998-2003 ? Honda Element 2003-2004 ? Honda Pilot 2003 ? Acura RSX 2002-2004 ? Acura CL 1998-2003 ? Acura TSX 2004 ? Acura Integra 2000-2002 ? Acura TL 2004 ? Acura MDX 2001-2002 ? Acura MDX 2003 ? Acura TL 1998-2002 ? Acura 1.7EL 2001-2004 ? Acura 1.6EL 1998-2000. 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. 2. Locate the appropriate wires exiting the ignition switch and immobilizer receiver. The wire colors are listed in the Wire Color Guide. 3. Wire the 556H as shown in the wiring diagram. GROUND BLACK (+) 12V BATTERYRED IGNITION IN PINK IGNITION OUT PINK/BLACK DATA YELLOW/BLACK DATA YELLOW N.C. ORANGE DATA 2 IN ORANGE/BLACK (-)GROUND IN BLUE/WHITE REFERENCE GREEN ?… Read More
Download 556H Honda / Acura Immobilizer Bypass Module Installation Instruction