chevy silverado fuel gage calibration

You search Auto repair manual PDF about chevy silverado fuel gage calibration, search results will appear below. If search results do not exist, please search by others keyword.

Edelbrock Pro-Flo EFI Fuel Rail for Honda Acura “B”and “D”Series INSTALLATION INSTRUCTIONS

Filed Under (Honda) by admin on 31-12-2013

Download
• DESCRIPTION: The Edelbrock Honda/Acura Fuel rails, Part # 4794,4796, and 4798, have been designed to fit stock, Edelbrock Victor X, or our Edelbrock Performer X manifolds using stock Honda injectors. Part #4795,4797, and 4799 accept Bosch-style injectors. These fuel rails feature a flow-through design 5/8″fuel passage with -8 AN o-ring threads at each end. They are fully CNC machined from aluminum extrusions, polished, then hard anodized for use with racing fuel (including methanol and alcohol). These fuel rails also include a fuel regulator mounting at the end of the rail that can be used with stock or aftermarket regulators, as well as two auxiliary 1/8″NPT ports for pressure gauge, nitrous system fuel supply, etc.  KIT CONTENTS: ?1 – Fuel Rail ?1 – O-Ring, 1/2″I.D. 1/16″Thick ?1 – Fuel Pressure Regulator Adapter ?2 – O-Ring, -8 AN ?1 – 12mm x1.0 Russell Honda Fuel Fitting (#4794,4795,4796 & 4797 Only) ?4 – O-Ring, 8mm I.D.… Read More

2003-2005 Ford Excursion DIESEL CALIBRATION UPDATE

Filed Under (Ford) by admin on 10-12-2013

Download 6.0L DIESEL CALIBRATION UPDATE—VARIOUS ISSUES 2003-2007 F-Super Duty FORD: 2004-2010 E-Series 2003-2005 Excursion This article supersedes TSB 9-7-11 to update the The PCM and FICM calibration update contains model years covered and Integrated Diagnostic improvement actions to address the following System (IDS) calibration level. symptoms: 2005 F-Super Duty 6.0L: ISSUE Some 2003-2007 F-Super Duty vehicles, 2003-2005 •False DTC P0470 – Exhaust pressure sensor A Excursions and 2004-2010 E-Series vehicles, circuit fault due to a freezing condition. equipped with a 6.0L diesel engine may exhibit hard •False DTC P0404 – Exhaust gas recirculation start, no start, white smoke, lack of power, running (EGR) performance due to a stuck turbocharger rough condition after cold engine start up, or condition. diagnostic trouble codes (DTCs) P0404, P0470, •Cooling loss protection – Revised engine P0611, P1260 and/or P1378 issues. Refer to the protection strategy when an engine Calibration Content for information detailing specific over-temperature condition is present.… Read More

Incorrect Fuel Gauge Readings (Reprogram VCM with Revised Calibration)

Filed Under (Other Manuals) by admin on 06-01-2014

Download Subject: Incorrect Fuel Gauge Readings (Reprogram Vehicle Control Module with Revised Calibration) Models: 1998*-99 Chevrolet and GMC S/T Pickup and 2 Door Utility Models 1998*-99 Isuzu Hombre with 4.3L Engine (VINs W, X – RPOs L35, LF6) *RPO ZN4 Only. Condition Some owners may comment on incorrect fuel gauge readings. The fuel gauge may read empty (E) with approximately 1/3 of a tank of fuel remaining, or the fuel gauge rarely reaches the full (F) mark when the fuel tank is filled. Correction Reprogram the vehicle control module (VCM) with the revised Fuel System Calibration. Use the appropriate calibration listed below. Refer to the latest Techline information for programming procedures. Calibration Information Important: These calibrations are not available from GMSPO. These calibrations are available on 1999 Techline CD ROM Disc 5 and later. Plant Division VIN Breakpoint Linden Chevrolet (Blazer) XK162355 Linden GMC (Pickup) XK508493 Linden GMC (Jimmy) XK508505 Shreveport Chevrolet X8140835 Shreveport GMC X8512385 Shreveport Isuzu (RPO ZN4 W8668201-W8670669 Shreveport Isuzu X8650007-X8650733.… Read More

Ford Focus PRO-FIT Linear Fuel Doors Installation Instructions

Filed Under (Ford) by admin on 31-12-2013

Download Tools you will need: ? Ratchet set ? Flathead screwdriver ? Drill and drill bits (for electric locking fuel door only) ? Small file ? Degreaser ? Clear Rags Parts list (items not to scale):1) Fuel door with pull cable attached (pull cable is on electric locking fuel door only) 2) Wiring harnesses (long and short) with actuator (electric locking fuel door only) 3) L-bracket (x 4) 4) Washer (x 4) 5) Nylock nut (x 4) 6) Long hex bolt (x 4) 7) Short hex bolt (x 6) 8) Fuse taps (3 sizes – electric locking fuel door only) 9) Fuse (electric locking fuel door only) 10) Switch (electric locking fuel door only) 11) Sticky pads (electric locking fuel door only) 12) Tie wraps (electric locking fuel door only) 13) Gas cap 14) Wrenches 15) Black strip caulk (not pictured) PRO-FIT Linear Fuel Doors Ford Focus – Installation Instructions Prep WARNING: Do not perform this install near a flame source due to the risk of fire or explosion from gas fumes.… Read More

1993 Ford Escort FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH)

Filed Under (Ford) by admin on 31-12-2013

Download 1993 Ford Escort G – TESTS W/CODES – EEC-IV (1.9L)’ ’1993 ENGINE PERFORMANCE Ford Motor Co. – Self-Diagnostics – EEC-IV. CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY & INERTIA SWITCH) Diagnostic Aids When ignition switch is in the ON or START position, the PCM connects FUEL PUMP circuit (PCM terminal No. 22) to ground. The fuel pump relay is energized and electrical current flows to the fuel pump. If PCM does not receive ignition PIP signal within 2 seconds, FUEL PUMP circuit is opened and fuel pump operation is terminated. Perform this test when instructed by QUICK TEST or CIRCUIT TEST AA. This test is only intended to diagnose: * Fuel pump relay. * Inertia Fuel Shutoff (IFS) switch. * Wiring harness circuits (B+, VPWR, FUEL PUMP, GND and POWER-TO-PUMP). * Faulty Powertrain Control Module (PCM). Fig. 31: Fuel Pump Monitor Circuit Diagram (Escort & Tracer) 1)Code 87/556: Check VPWR To Fuel Pump Relay Code 87/556 indicates a fuel pump primary circuit failure.… Read More

FORD 302/351 WINDSOR FUEL RAIL INSTALLATION INSTRUCTION

Filed Under (Ford) by admin on 20-03-2014

Download
1. Disconnect the fuel injector wiring connectors and remove the existing fuel rails. Remove fuel injectors from manifold base and set aside. 2. Attach the four (4) supplied mounting tabs and eight (8) #10-24 screws to the fuel rail. Orient the tabs so that the slot angle is parallel with the injector bores. The tabs are designed to allow adjustment to compensate for various injector heights and manifold tolerances. 3. Apply a small amount of oil on supplied fittings and O-rings. Install into the rails as shown in the fuel line attachment examples on the following page. 4. Snap the supplied retainers into the top groove on each fuel injector as shown in Fig. A to the right. Lubricate the injector O-rings with a small amount of oil. Insert the injectors into the fuel rail until the retainer is seated. 5. Install both of the fuel rail/injector assemblies onto the manifold base (the longer rail with the hex plug at the front is to be installed on the driver’s side to provide clearance for distributor).… Read More

Ford Mustang Fuel Injection Conversion

Filed Under (Ford) by admin on 04-05-2012

Download These instructions will provide the basic and necessary information to allow a carbureted 302 to be converted to SEFI Fuel Injection. There are several different types of fuel injection conversions available, however, this instruction will concentrate on the High Output, MASS-AIR setups found on the 92-93 Ford Mustangs. There are two main advantages to using this type of setup. The first advantage is that the computer in the MASS-AIR system will automatically compensate for any engine modifications that have been done prior to the installation of the fuel injection system. The second advantage is that fuel is sent to each cylinder individually only during the appropriate firing cycle, meaning that fuel is sent sequentially to each cylinder only when the spark plug is ready to fire. This makes for an extremely efficient firing cycle . SEFI stands for Sequential Electronic Fuel Injection. This system is complex to be sure, therefore, this instruction is going to skip all the technical mumbo-jumbo, and focus on the bare essentials to install this system properly.… Read More

2004 Audi A4 Fuel Pump Removing And Installing FWD

Filed Under (Audi) by admin on 07-01-2014

Download 2004 Audi A4 L4-1.8L Turbo (AMB) Vehicle Level Powertrain Management Fuel Delivery and Air Induction Fuel Pump Service and Repair Fuel Pump, Removing And Installing FWD. Removing And Installing Fuel Pump CAUTION: To remove the Fuel Pump (FP), the fuel tank may only be filled to a maximum of 3/4. Empty fuel tank if necessary. Recommended special tools and equipment 3087 wrench for tank sensor. VAS5190 fuel siphoning device Empty fuel tank Observe safety precautions. Observe rules for cleanliness. CAUTION: Observe safety precautions when disconnecting the battery. Disconnect battery Ground (GND) strap with the ignition switched off. CAUTION: Secure Ground (GND) wire of VAS5190 to a blank portion of the chassis. Pull cone piece -2- from shaft piece -1- of VAS 5190. Using insulating tape, apply a mark -arrow- on hose at length a = 1465 mm from end of suction hose. Remove fuel filler cap from fuel filler tube.… Read More

2001 Chevrolet Chevy K Silverado Crankshaft Position Sensor Engine Stall

Filed Under (Chevrolet (Chevy)) by admin on 31-12-2013

Download Models: 2001 Chevrolet Silverado, Suburban 2001 GMC Sierra, Yukon XL Equipped with 8.1L V8 (RPO L18 – VIN G) Engine. Condition General Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 2001 model year Chevrolet Silverado, Suburban; GMC Sierra and Yukon XL model vehicles, equipped with an 8.1L V8 (RPO L18 – VIN G) engine. Some of these vehicles have a condition in which the crankshaft position sensor can fail intermittently or permanently. If the sensor fails intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool down period. If the sensor fails permanently, the engine will quit running and will not re-start. Correction Dealers are to replace the crankshaft position sensor. Vehicles Involved Involved are certain 2001 model year Chevrolet Silverado, Suburban; GMC Sierra and Yukon XL model vehicles, equipped with an 8.1L V8 (RPO L18 – VIN G) engine and built within these VIN breakpoints: Subject: 06083 — Crankshaft Position Sensor Engine Stall Models: 2001 Chevrolet Silverado, Suburban 2001 GMC Sierra, Yukon XL Equipped with 8.1L V8 (RPO L18 – VIN G) Engine Year Division Model From Through 2001 Chevrolet Silverado iE100004 1E200999 1F100006 1F116767 1M100002 1M103668 1Z100010 1Z100042 2001 Chevrolet Suburban 1G100001 1G174359 1J100010 1J100058 2001 GMC Sierra 1E100003 1E2012022 1F100004 1F113912 1M100023 1M103669 1Z100013 1Z100026.… Read More

2005 Chevrolet Chevy K Silverado Panel Cluster Gauge Needle Function

Filed Under (Chevrolet (Chevy)) by admin on 24-02-2014

Download Subject: 07187C — SPECIAL COVERAGE ADJUSTMENT – INSTRUMENT PANEL CLUSTER GAUGE NEEDLE FUNCTION Models: 2003-2004 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT 2005 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT (U.S. ONLY) 2003-2004 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE 2005 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE (U.S.ONLY) 2003-2004 GMC SIERRA, YUKON, YUKON XL 2005 GMC SIERRA, YUKON, YUKON XL (U.S. ONLY) Condition Some customers of all 2003-2004 model year and certain U.S. 2005 model year Cadillac Escalade, Escalade ESV, and Escalade EXT; Chevrolet Avalanche, Silverado, Suburban, and Tahoe; and GMC Sierra, Yukon, and Yukon XL vehicles have reported that one or more of the instrument panel (IP) cluster gauges stick, flutter, or become inoperative. This may cause inaccurate readings, including the speedometer and fuel gauge. Special Coverage Adjustment This special coverage covers the condition described above for a period of 7 years or 70,000 miles (110,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership.… Read More

You might also likeclose