chevy impala blower resister wiring

You search Auto repair manual PDF about chevy impala blower resister wiring, search results will appear below. If search results do not exist, please search by others keyword.

2005 Chevy Truck Silverado 1500 Blower Motor Resistor Replacement

Filed Under (Chevrolet (Chevy)) by admin on 09-12-2013

Download 2005 Chevy Truck Silverado 1500 2WD V8-5.3L VIN T Vehicle Level Heating and Air Conditioning Blower Motor Resistor Service and Repair Blower Motor Resistor Replacement. BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor. 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.… Read More

2004 Pontiac Grand Prix Blower Motor Inoperative or Intermittent

Filed Under (Pontiac) by admin on 16-12-2013

Download 2004 Pontiac Grand Prix | Grand Prix (VIN W) Service Manual Subject: Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) Models: 2005 Buick Allure (Canada Only), LaCrosse 2004-2005 Pontiac Grand Prix. 2004 Pontiac Grand Prix | Grand Prix (VIN W) Service Manual | Document ID: 1644694 #05-01-39-001A: Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) – (Apr 6, 2005) This bulletin is being revised to update Step 5 of the service procedure. Please discard Corporate Bulletin Number 05-01-39-001 (Section 01 — HVAC). Condition Some customers may comment on an inoperative or intermittent Heating, Ventilation and Air Conditioning (HVAC) blower motor. Others may comment that the blower motor speed may momentarily drop or that the blower motor continues to run after the key is turned off.… Read More

2002 Crown Victoria/Grand Marquis Workshop Manual

Filed Under (Ford) by admin on 31-12-2013

Download Adjust the blower motor setting to LO and then to HI. * Does the blower motor operate correctly? Yes REPAIR circuit 515 (OG/RD) for a short to ground. TEST the system for normal operation. No GO to R2 . R2 CHECK THE BLOWER MOTOR SPEED CONTROL Blower Motor Speed Control C1308 EATC Module C228b * Does the blower motor operate? Yes INSTALL a new blower motor speed control. TEST the system for normal operation. No GO to R3 . R3 CHECK THE BLOWER MOTOR SPEED CONTROL CIRCUITS FOR AN OPEN Blower Motor Speed Control C1308 Measure the resistance between the blower motor speed control C1308: * pin 1, circuit 269 (LB/OG) and the EATC module C228b pin 10. * pin 2, circuit 752 (YE/RD) and the EATC module C228b pin 23. * pin 3, circuit 754 (LG/WH) and the EATC module C228b pin 24. * Are the resistances less than 5 ohms?… Read More

2000 Chevrolet Blazer MANUAL A/C-HEATER SYSTEMS

Filed Under (Chevrolet (Chevy)) by admin on 16-12-2013

Download 1. Disconnect the electrical connector (3). 2. Remove the blower motor resistor mounting screws (1). 3. Remove the blower motor resistor (2) from the blower case. Fig. 3: Identifying Blower Motor Resistor Assembly (C42) Courtesy of GENERAL MOTORS CORP. Installation Procedure (C42) 1. Install the blower motor resistor (2) to the blower case. 2. Install the blower motor resistor mounting screws (1). Tighten Tighten the screws to 1.9 N.m (17 lb in). 3. Connect the electrical connector (3). Removal Procedure (C60) 1. Remove the A/C control relay bracket with the relay. 2. Remove the blower resistor harness. 3. Remove the stud from the IP, if necessary. 4. Remove the blower motor resistor mounting screw. 5. Cut the access cover from the case. Cut all four sides of the cover in order to remove the three attaching screws. Use a sharp utility knife in order to cut the case. Make the cuts straight and clean.… Read More

2005 Ford Mustang GT Roush Fog Lamp Wiring Harness Installation Instructions

Filed Under (Ford) by admin on 01-01-2014

Download 1. SAFETY REQUIREMENTS STOP! READ IMPORTANT SAFETY CAUTIONS AND WARNINGS BEFORE PROCEEDING. IMPORTANT SAFETY NOTICE Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the actual installation. 1. Always wear safety glasses for eye protection. 2. Place ignition switch in the OFF position. 3. Always apply the parking brake when working on a vehicle. 4. Block the front and rear tire surface to prevent unexpected vehicle movement. 5. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide. 6. Do not smoke or use flammable items near or around the fuel system. 7. Use chemicals and cleaners in well-ventilated areas. 8. Batteries produce explosive gases, which can cause personal injury.… Read More

2002 Ford Taurus WATER IN THE BLOWER CASE

Filed Under (Ford) by admin on 09-12-2013

Download FORD: 2001-2004 Taurus MERCURY: 2001-2004 Sable This article supersedes TSB 03-15-06 to update the vehicle model years and build date information. ISSUE Some vehicles built between 5/1/2001 and 12/15/2003 may exhibit water in the blower case or on the passenger side floor, an inoperative climate control blower motor , a motor that operates on high speed only, and/or a blower motor resistor failure. ACTION Inspect and seal cowl area and install Rain-Hat Extension Seal. Inspect and replace blower motor and/or blower motor resistor if there is evidence of water/corrosion. Refer to the following Service Procedure for details. SERVICE PROCEDURE 1. Access blower motor and resistor per the Workshop Manual Sections 412-02 and 412-04. Inspect for evidence of water/corrosion. If water/corrosion are found or parts have failed, replace per Workshop Manual (blower motor 1F1Z- 19805-AA and resistor F6DZ-19A706-AA). 2. Visually inspect the Cowl Vent Screen located under the RH windshield wiper to verify if the screen is fully seated.… Read More

Service 4WD Light Illuminated, DTC C0374 Set (Inspect Wiring Harness to Transfer Case Speed Sensors, Replace Wiring Harness)

Filed Under (Other Manuals) by admin on 01-01-2014

Download Models: 2004-2007 Buick Rainier 2003-2006 Chevrolet Avalanche, Suburban, Tahoe 2003-2007 Chevrolet Silverado Classic, TrailBlazer, TrailBlazer EXT 2003-2006 GMC Yukon, Yukon XL 2003-2007 GMC Envoy, Envoy XL, Sierra Classic 2003-2004 Oldsmobile Bravada 2005-2007 Saab 9-7X with Four Wheel Drive or All-Wheel Drive and Active All-Wheel Drive (RPO NP4) or Active Two-Speed (RPO NP8) Transfer Case. Condition Some customers may comment on intermittent illumination of the Service 4WD light. Upon investigation, the technician may find DTC C0374 set. The customer may also comment on intermittent erratic operation of the 4WD or AWD system after driving through rain/snow or simply going through a car wash. Cause The speed sensor signal may have become corrupted. Possible openings in the speed sensor wire insulation (twisted pairs) can allow water intrusion. Also, wire connections contaminated by water may result in short circuits and erroneous speed sensor readings. This most often occurs on the rear speed sensor circuit.… Read More

1994 Chevy Truck C 1500 Ignition – Timing Connector Location Change

Filed Under (Chevrolet (Chevy)) by admin on 07-02-2014

Download 1994 Chevy Truck C 1500 Truck 2WD V6-262 4.3L VIN Z Vehicle Level Maintenance Tune-up and Engine Performance Checks Ignition Timing Technical Service Bulletins Ignition – Timing Connector Location Change. INFORMATION SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1).… Read More

2001 Chevrolet Chevy K Silverado Transmission Stuck in Second or Third Gear

Filed Under (Chevrolet (Chevy)) by admin on 19-12-2013

Download Malfunction Indicator Lamp (MIL) On, Transmission Stuck in Second or Third Gear, Instrument Cluster Inoperative (Verify and Repair Source of Voltage Loss In Transmission Solenoid Power Supply Circuit ) Models: 2006 and Prior GM Passenger Cars and Light Duty Trucks 2005-2006 HUMMER H2 2006 HUMMER H3 2005-2006 Saab 9-7X with 4L60-E, 4L65-E, 4L80-E or 4L85-E Automatic Transmission (RPOs M30, M32, M33, MT1, MN8) Condition Some customers may comment on one or more of the following conditions: Upon investigation, one or all of the diagnostic trouble codes (DTCs) P0740, P0753, P0758, P0785, P0787, P0973, P0976, P1860, P2761, P2764 and P2769 may be set depending on the vehicle. Cause The most likely cause of this condition may be a loss of voltage to the transmission solenoid power supply circuit. This condition may also be the result of an incorrect installation of an aftermarket electronic device such as a remote starter or alarm system.… Read More

2000 Chevy Truck S10/T10 Transfer Case Replacement

Filed Under (Chevrolet (Chevy)) by admin on 28-11-2013

Download 2000 Chevy Truck S10/T10 Blazer 4WD V6-4.3L VIN W Vehicle Level Transmission and Drivetrain Transfer Case Service and Repair NVG 233/243-NP1 Transfer Case Replacement. Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 7. Remove any wiring harness from the transfer case. 8. Support the transfer case with a transmission jack. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case. 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case.… Read More

You might also likeclose