buick lesabre bypass vats system

You search Auto repair manual PDF about buick lesabre bypass vats system, search results will appear below. If search results do not exist, please search by others keyword.

2004 Buick LeSabre Shake/Vibration in Steering Wheel

Filed Under (Buick) by admin on 31-12-2013

Download 2004 Buick LeSabre | LeSabre (VIN H) Service Manual. Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) Condition Some customers may comment on shaking/vibration in the steering wheel, floor or seat while driving at highway speeds (typically between 60-72 mph (96-115 km/h)) on smooth roads. Cause These specific vehicles may be sensitive to various rotating mass assemblies, especially if they are considered to be out-of-balance. Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights 3.… Read More

How to bypass the VATS (PASSKey II) system in a late model GM vehicle

Filed Under (Other Manuals) by admin on 21-12-2013

DownloadPontiac 1994-1996 Grand Prix 1992-1999 Bonneville 1993-2002 Firebird/Trans Am/Firehawk Buick 1994-1996 Regal 1992-1999 LeSabre 1991-1996 Park Avenue 1991-1996 Roadmaster Oldsmobile 1994-1997 Cutlass Supreme 1992-1999 Eighty Eight/LSS/Ninety Eight/Regency 1991-1996 Custom Cruiser Wagon Chevrolet 1995-1999 Monte Carlo 1995-2001 Lumina 1993-2002 Camaro 1986(?)-1996 Corvette (C4) Cadillac 1991-1996 Fleetwood 1992-1997(?) Seville/STS/DeVille Any other GM Vehicles with the VATS or PASSKey II system (If your ignition key looks like the one pictured below.) Alright, let’s begin the madness: 1. Take your DMM, set it to measure Ohms (use the 20k setting.) Measure the resistance across the pellet of the ignition key. Place one probe on the silver part of one side of the pellet, and the other probe on the other side. Write this value down. 2. Purchase a resistor or resistors that add up to the value measured in step 1. Radio Shack is a great place to go for the resistors, heat shrink tubing, and the “bullet-style” solderless connectors.… Read More

1997-1999 Buick Century/Regal 99-2001 AW-200GM INSTALLATION INSTRUCTIONS

Filed Under (Buick) by admin on 05-01-2014

Download BUICK Century 1997-99 LeSabre 1995-99 1 Park Avenue 1995-99 Regal 1995-99 Riviera 1996-99 Roadmaster 1995-96 Skylark 1996-98 CHEVROLET Impala 2000 Venture 2000 OLDSMOBILE Achieva 1996-98 Aurora 1995-99 Bravada 1998-99 Cutlass 1998-99 Cutlass Supreme 1995-97 Eighty-Eight 1994-99 Intrigue 1998-99 LSS 1996-99 Ninety-Eight 1994-96 Regency 1997-98 Silhouette 2000 PONTIAC Montana 2000 Sunfire 2000. BUICK LeSabre / Park Avenue 1995-99 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the plastic trim piece to the left of the glove box and (1) Phillips screw exposed. Unsnap the top edge of the knee bolster panel. Remove (1) Phillips screw from the panel. Remove the ashtray cluster and (2) Phillips screws from each side. Unclip the entire dash trim bezel and remove. Remove (3) 9/32″ hex-head screws securing the factory head unit and disconnect the wiring. Skip to the Installation Instructions for ALL VEHICLES on Page #6. CHEVROLET Impala 2000 Disconnect the negative battery terminal to prevent an accidental short circuit.… Read More

1998 Buick Park Avenue Engine Coolant Consumption or Coolant Leak

Filed Under (Buick) by admin on 20-01-2014

Download Engine Coolant Consumption or Coolant Leak (Inspect For Material Degradation/Replace Intake Manifolds) Models: 1995-1997 Buick Riviera 1995-1999 Buick LeSabre, Park Avenue 1996-1999 Buick Regal 1998-1999 Chevrolet Lumina, Monte Carlo 1995-1996 Oldsmobile Ninety-Eight 1995-1999 Oldsmobile Eighty-Eight 1998-1999 Oldsmobile Intrigue 1995-1999 Pontiac Bonneville 1997-1999 Pontiac Grand Prix with 3.8L Engine (VIN K — RPO L36) Condition Some customers may comment on excessive engine coolant consumption, or an engine coolant leak near or under the throttle body area of the upper intake manifold. Cause Upper intake manifold composite material may degrade around the EGR stove pipe and could result in an internal or external coolant leak. Correction 1. Follow the upper intake manifold removal instructions found in the Engine Unit Repair Section of the Service Information Manual. 2. Refer to the arrow in the illustration of the upper intake manifold above. Inspect the inner diameter of the EGR passage for signs of material degradation.… Read More

Buick Performer & B4B Manifold For 400-455 c.i.d. Buick V8 Engines Catalog #2146 and #2515 INSTALLATION INSTRUCTIONS

Filed Under (Buick) by admin on 31-12-2013

Download 1. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 2. Apply Edelbrock Gasgacinch sealant PN 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. (Refer to instructions on Gasgacinch can for further reference). If you are using two-piece gaskets with a seperate tray, the valley pan will contact the cylinder heads with the gaskets resting on top. Both sides of the gaskets and pan should be coated with a layer of Gasgacinch. 3. Do not use cork or rubber end seals. Use RTV silicone sealer instead. Apply a ¼” high bead across each block end seal surface, overlapping the intake gasket at the four corners. This method will eliminate end seal slippage. 4. Install the intake manifold and the intake manifold bolts with hardened steel washers between the manifold and the bolt heads.… Read More

PERFORMER RPM BUICK CYLINDER HEADS For 1967-1981 400-455 Buick V8 Engines Catalog #60039 #60049 INSTALLATION INSTRUCTIONS

Filed Under (Buick) by admin on 09-01-2014

Download Installation is the same as for original equipment cylinder heads. Consult service manual for specific procedures, if necessary. Be sure that the surface of the block and the surface of the head are thoroughly cleaned to remove any oily film before installation. Use alcohol or lacquer thinner on a lint-free rag to clean. Apply oil or suitable thread lubricant to head bolt threads and the underside of bolt heads and washers to prevent galling and improper torque readings. Use thread sealant on any bolts that go into coolant passages. Torque top row of bolts to 110 ft./lbs. and bottom row of bolts to 100 ft./lbs. in three or four steps, following the factory tightening sequence (See Figure 1) . A re-torque is recommended after the initial star-up and cool-down (allow 2-3 hours for adequate cooling). Other Assembly Tips: When installing the sparkplugs and exhaust manifolds, be sure to use a high temperature anti-seize compound on the threads to reduce the possibility of thread damage in the future.… Read More

1997 Buick Century COLD ENGINE TICK OR RATTLE AFTER START-UP

Filed Under (Buick) by admin on 05-04-2014

Download 1997 Buick Century Limited 3.1/3.4L ENG TICK OR RATTLE AFTER COLD START UP COLD ENGINE TICK OR RATTLE AFTER START-UP (REPLACE PISTON/PIN ASSEMBLY) Model(s): 1994-95 Buick Regal 1994-97 Buick Skylark 1994-98 Buick Century 1994-95 Chevrolet Beretta Corsica, Lumina, Monte Carlo 1996-98 Chevrolet Venture 1997-98 Chevrolet Malibu 1993-97 Oldsmobile Cutlass Supreme 1994-96 Oldsmobile Cutlass Ciera 1994-97 Oldsmobile Achieva 1996-98 Oldsmobile Silhouette 1997-98 Oldsmobile Cutlass 1994-98 Pontiac Grand Am, Grand Prix 1996-98 Pontiac Trans Sport with 3100, 3400 V6 Engine (VINs M, E – RPOs L82, LA1) CONDITION Some customers may comment on a ticking type noise that begins shortly after cold engine start-up and gradually diminishes as the engine warms up. In most cases, the noise is gone after five (5) minutes. In severe cases, the noise may not disappear when lhe engine is hot. CAUSE Under normal design tolerances when the piston pin bore is produced at the maximum tolerance and the piston pin is produced at the minimum tolerance (min-max tolerance) trace noise levels can occur.… Read More

Information on Error Codes on Radio Display – Their Cause and Corrective Action

Filed Under (Other Manuals) by admin on 25-12-2013

Download odels: 1995-1996 Buick Roadmaster 1995-1999 Buick LeSabre 1995-2004 Buick Century, Regal 1995-2005 Buick Park Avenue 1996-1999 Buick Riviera, Skylark 2004-2005 Buick Rainier 1995-1999 Chevrolet Lumina, Monte Carlo, Fullsize Pickup Models (Old Style) 1995-2005 Chevrolet Blazer 1996 Chevrolet Lumina APV 1996-1999 Chevrolet Cavalier 1996-2000 Chevrolet Express Van 1996-2002 Chevrolet Astro Van 1997-2002 Chevrolet Camaro 1997-2003 Chevrolet Malibu 1997-2005 Chevrolet Corvette, Venture 2000-2005 Chevrolet Silverado 2002-2005 Chevrolet Avalanche, TrailBlazer, TrailBlazer EXT 2003-2005 Chevrolet SSR 2004-2005 Chevrolet Classic, Colorado 1995-1999 GMC Fullsize Pickup Models (Old Style) 1995-2002 GMC Jimmy 1996-2000 GMC Savana Van 1996-2002 GMC Safari Van 2000-2005 GMC Sierra 2002-2005 GMC Envoy, Envoy XL 2004-2005 GMC Canyon, Envoy XUV 1995-1999 Oldsmobile Aurora, Eighty Eight 1995-1997 Oldsmobile Cutlass Supreme 1999-2004 Oldsmobile Alero 1998-2002 Oldsmobile Intrigue 1995-1996 Oldsmobile Ninety Eight 1996-1999 Oldsmobile Achieva 1996-2004 Oldsmobile Bravada, Silhouette 1995-1999 Pontiac Bonneville, Sunfire 1995-2002 Pontiac Firebird 1995-2005 Pontiac Grand Prix 1996-1997 Pontiac Trans Sport 1996-2000 Pontiac Grand Am 1997-2005 Pontiac Montana 2003-2005 HUMMER H2.… Read More

2007 Chevrolet Impala Transmission 1-2 Shift Shudder at Light to Moderate Acceleration

Filed Under (Chevrolet (Chevy)) by admin on 23-12-2013

Download Models: 2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission (RPOs MN3, MN7, M15, M76) Supercede: This bulletin is being revised to update parts information. Please discard Corporate Bulletin Number 06-07-30-023B (Section 07 – Transmission/Transaxle) . Condition Some customers may comment on a 1-2 shift shudder at light to moderate acceleration. Typically, the throttle plate angle parameter is 12-20% at time of condition with vehicle speed of approximately 24-40 km/h (15-25 mph). The customer may describe the condition as slip or delayed shift into second. Correction Replace the complete second clutch assembly with service kit, P/N 24240561.… Read More

Steering Vibration/Shudder During Parking Manuever

Filed Under (Other Manuals) by admin on 07-02-2014

Download Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville. Condition Some customers may comment on a steering vibration, shudder or moan noise when steering during parking maneuvers on dry pavement. Correction Install a new power steering pressure (inlet) hose assembly on the following vehicles: Install a new power steering pressure (inlet) and return (outlet) hose assembly on the following vehicles: Diagnosis Important: In diagnosing the above listed vehicles, do not overlook other obvious repairs prior to replacing the hose(s). 1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions.… Read More

You might also likeclose