1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

FORD FOCUS POWER WINDOW INSTALLATION INSTRUCTIONS

Download Tools & Materials Needed: 1. Utility Knife 2. Wire Crimper 3. Torx™ Wrenches 4. Hex Nut Drivers 5. Drill and Bits 6. Phillips Head Screw Driver 7. Crank Spring Removal Tool (Special Tool, available at most Auto Parts Stores) – or – 8. Flat Screw Drivers (2) 9. Add-A-Circuit ™ fuse adapter 10. Silicon Sealant (Clear or Black) Procedure: (Approximate time to complete installation: 3 – 4 hours) A. Removing the Door Panel Coverings 1. For ease of installation, do both sides at the same time. 2. Roll the windows to approximately 1/2 open, and so the crank handle is in the Down Position. With either the Crank Spring Removal Tool, or a flat Screwdriver, remove the spring, located in a slot on the back of the crank. 3. Remove the cover plate for the remote-control mirror, which is held in place by 3 spring clips. Remove by gently pulling the front corner of the cover out, and then slide the cover back.… Read More

1997-1999 Buick Century/Regal 99-2001 AW-200GM INSTALLATION INSTRUCTIONS

Download BUICK Century 1997-99 LeSabre 1995-99 1 Park Avenue 1995-99 Regal 1995-99 Riviera 1996-99 Roadmaster 1995-96 Skylark 1996-98 CHEVROLET Impala 2000 Venture 2000 OLDSMOBILE Achieva 1996-98 Aurora 1995-99 Bravada 1998-99 Cutlass 1998-99 Cutlass Supreme 1995-97 Eighty-Eight 1994-99 Intrigue 1998-99 LSS 1996-99 Ninety-Eight 1994-96 Regency 1997-98 Silhouette 2000 PONTIAC Montana 2000 Sunfire 2000. BUICK LeSabre / Park Avenue 1995-99 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the plastic trim piece to the left of the glove box and (1) Phillips screw exposed. Unsnap the top edge of the knee bolster panel. Remove (1) Phillips screw from the panel. Remove the ashtray cluster and (2) Phillips screws from each side. Unclip the entire dash trim bezel and remove. Remove (3) 9/32″ hex-head screws securing the factory head unit and disconnect the wiring. Skip to the Installation Instructions for ALL VEHICLES on Page #6. CHEVROLET Impala 2000 Disconnect the negative battery terminal to prevent an accidental short circuit.… Read More

2000 Buick Regal Oil Pan Replacement

Download Tools Required z J 28467-90A Engine Support Adapters z J 28467-B Universal Engine Support Fixture z J 36462-A Engine Support Adapter Leg Set 1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical. 2. Carefully disconnect the throttle body air inlet duct. 3. Remove the engine mount struts from the engine. Refer to Engine Mount Strut Replacement . 4. Remove the drive belt. Refer to Drive Belt Replacement . 5. Install the J 28467-90A , the J 28467-B and the J 36462-A . Do not raise the engine. Refer to Engine Support Fixture . 6. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 7. Disconnect the three-way catalytic converter pipe from the right exhaust manifold. Refer to Catalytic Converter Replacement in Engine Exhaust. 8. Remove the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.… Read More

2000-2005 Ford Explorer Wheel Bearings REMOVAL & INSTALLATION

Download 1. Before servicing the vehicle, please familiarize yourself with safety procedures. 2. Remove the axle”to”wheel hub retainer nut and washer. 3. Remove the parking brake shoes. 4. Press the outboard CV”joint until it is loose from the hub. 5. Remove and discard the toe link”to”wheel knuckle nut. 6. Remove the bolt and separate the toe link from the wheel knuckle. 7. Remove and discard the upper arm”to”wheel knuckle nut. 8. Remove the bolt and separate the upper arm from the wheel knuckle. 9. Remove and discard the lower arm”to”wheel knuckle nut. 10. Remove the lower arm”to”wheel knuckle bolt. 11. Remove the wheel knuckle. 12. Using a suitable press, remove and discard the wheel hub. 13. Remove and discard the wheel bearing retainer ring. 14. Using a suitable press, remove the wheel bearing. Fig. Rear hub/bearing Assembly”Aviator, Explorer and Mountaineer Fig. Pressing out the bearing 1. Installation is the reverse of the removal procedure.… Read More

2002 Ford Explorer/Mountaineer Workshop Manual

Download CAUTION: Since the engine is not free-wheeling, timing procedures must be followed exactly or piston and valve damage may occur. 1. Remove the engine front cover (6019). For additional information, refer to Engine Front Cover in this section. 2. NOTE: Procedure is for either RH or LH ignition coil (12029); LH ignition coil is shown. Disconnect the ignition coil electrical connector and remove the retaining bolt. 3. Tilt the coil away from the fuel injection supply manifold. 4. Remove the ignition coil. 5. NOTE: Remove any foreign material from the spark plug wells with compressed air before removing the spark plugs. Remove the spark plugs. 6. Position the lobe of the camshaft up. 7. Install the special tool between the valve spring coils to prevent valve stem seal damage. 8. NOTE: The roller followers are positional. Mark the followers for installation in their original locations. NOTE: The last three roller followers must be removed with special service tool 303-581.… Read More

2002 Land Rover Freelander Camshaft Timing Belt Service Repair

Download Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated. Align Front Timing Belt. 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate.… Read More

AUDI TT Sport Sway Bar Kit 22806

Download Installation of Hotchkis Front Sway Bar 1F Raising Vehicle Raise front of the vehicle by using a 4 post lift or drive-on ramps. Securely block the rear wheels of the vehicle. Do not remove the front wheels during installation for safety. 2F Observe Orientation Of the Bar Remove the lower splash shield, and observe the location and orientation of the front swaybar. 3F Remove End Links Locate and remove the lower end link nuts from both sides, and push links aside. 4F Remove Engine Mount Locate and remove lower engine mount that attaches to subframe. The engine may want to shift forward which is ok. 5F Remove Exhaust Hanger Use a pry bar to remove the exhaust hanger located behind subframe. 6F Ride Height Sensor Locate the ride height sensor located on the drivers side lower control arm, and remove the nut from the stud that attaches the sensor to the arm.… Read More

2000-2002 Audi Quattro StartupRacing Contest and Competition Suspension Installation Manual

Download B5 Audi Quattro (2000-2002 Audi S4 and 1996-2001 Audi A4). Suspension Removal General 1. Loose wheel bolts 2. Raise the car and support it with two or four jack stands (if only using two, support front first, then rear) 3. Remove wheels Front 1. Remove the bolt that attaches the shock clevis to the control arm. (18mm and 19mm) 2. Remove upper control arm bolt (16mm) 3. Disconnect the upper control arms from the upright (WD40 helps here) 4. Open the hood, and remove the plastic piece hiding the battery, along with the pollen filter cover (8mm) 5. Remove these three identical bolts. They hold the upper control arm plate, as you remove the last bolt, make sure you hold the shock body as it will be loose. (16mm) Remember the orientation of washers as you remove them. 6. Remove the OEM shock along with the spring, and place on a clean flat surface.… Read More

2007-2009 HONDA 420 RANCHER 2×4/4×4 CLUTCH KIT INSTALLATION INSTRUCTIONS

Download
ATV’s can be dangerous. EPI has no control over the use of any part. EPI expects the customer to exercise good judgment as to the proper selection, installation, use and maintenance of any part. EPI assumes no responsibility for damage or injury of any kind because of misuse, improper installation and improper application of any parts in any way by any person. Contact your local dealer to schedule installation of this clutch kit if you are not a qualified ATV mechanic. This product is NOT to be installed on any ATV that will be used by any person under the age of 16. Tools needed to install clutch kit – Metric socket set – 27mm socket – 1/2″ impact wrench – Torque wrench – Phillips and flat tip screwdrivers – Spring tool or bent pliers – 5mm Allen wrench – 10mm & 14mm wrench – 2 C-Clamps – Honda clutch tool #07933-HB3000A – Honda motor oil – Honda coolant – Honda Bond or Yamabond Semi-drying liquid gasket (or similar semi-drying liquid gasket) GASKETS NEEDED TO INSTALL CLUTCH KIT – None, only need tube of semi-drying liquid gasket ENGAGEMENT – 25-2,600 rpm’s 1.… Read More