blend door actuator install for grand prix

You search Auto repair manual PDF about blend door actuator install for grand prix, search results will appear below. If search results do not exist, please search by others keyword.

1999 Chrysler Truck Blend Door Actuator Replacement

Filed Under (Chrysler) by admin on 12-03-2014

Download 1999 Chrysler Truck Town & Country LWB FWD V6-3.8L VIN L Vehicle Level Heating and Air Conditioning Air Door Air Door Actuator / Motor Service and Repair Blend Door Actuator Replacement. REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes.… Read More

2005 HONDA CR-V DOOR VISORS INSTALLATION INSTRUCTIONS

Filed Under (Honda) by admin on 24-12-2013

Download
PARTS LIST Left front door visor Right front door visor Left rear door visor Right rear door visor Installing the Front Door Visor 1. Lower the front door glass completely. Remove the door glass run channel from the door sash in the area shown. Do not remove the glass run channel from the door mirror base or the rear end of the door. AII 27171 TOOLS REQUIRED Isopropyl alcohol Shop towel Masking tape INSTALLATION NOTE: •These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors. Be careful not to damage the paint finish or glass run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours.… Read More

2004 Pontiac Grand Prix Blower Motor Inoperative or Intermittent

Filed Under (Pontiac) by admin on 16-12-2013

Download 2004 Pontiac Grand Prix | Grand Prix (VIN W) Service Manual Subject: Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) Models: 2005 Buick Allure (Canada Only), LaCrosse 2004-2005 Pontiac Grand Prix. 2004 Pontiac Grand Prix | Grand Prix (VIN W) Service Manual | Document ID: 1644694 #05-01-39-001A: Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) – (Apr 6, 2005) This bulletin is being revised to update Step 5 of the service procedure. Please discard Corporate Bulletin Number 05-01-39-001 (Section 01 — HVAC). Condition Some customers may comment on an inoperative or intermittent Heating, Ventilation and Air Conditioning (HVAC) blower motor. Others may comment that the blower motor speed may momentarily drop or that the blower motor continues to run after the key is turned off.… Read More

2002 Pontiac Grand Prix GT THERMOSTAT REPLACEMENT

Filed Under (Pontiac) by admin on 21-01-2014

Download 2002 Pontiac Grand Prix GT 2002 ENGINE Engine Cooling – Grand Prix THERMOSTAT REPLACEMENT (3.1 L) Tools Required J 38185 Hose Clamp Pliers Removal Procedure 1. Remove the air cleaner intake duct. Refer to AIR CLEANER INTAKE DUCT . 2. Partially drain the cooling system. Refer to Draining and Filling Cooling System . 3. Use the J 38185 in order reposition the hose clamp from the water outlet housing. 4. Remove the radiator inlet hose from the water outlet housing. 5. Remove the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) 6. Remove the water outlet housing bolts. 7. Remove the water outlet housing and gasket. 8. Remove the thermostat. 9. Clean the water outlet housing mating surfaces. Installation Procedure 1. Install the thermostat. 2. Install the water outlet gasket and the water outlet housing. 3. Install the water outlet housing bolts.… Read More

1998 Pontiac Grand Prix Fuel Pump Resistor Service Manual

Filed Under (Pontiac) by admin on 31-12-2013

Download Subject: 01033 — Fuel Pump Resistor Models: 1997-1998 Buick Regal GS & Pontiac Grand Prix GTP with L67 3.8L V6 Engine (Located in the High Corrosion Provinces of Newfoundland, Nova Scotia, Prince Edward Island, New Brunswick, Quebec and Ontario) Condition General Motors has decided that all 1997-1998 Buick Regal GS and Pontiac Grand Prix GTP model vehicles equipped with L67 3.8L V6 engines, located in the high corrosion provinces of Newfoundland, Nova Scotia, Prince Edward Island, New Brunswick, Quebec and Ontario, may develop an electrical open in the fuel pump resistor. This condition prevents operation of the fuel pump and the engine will not run. Correction Dealers are to install a new resistor on the plenum with an aesthetic cover. Vehicles Involved Involved are all 1997-1998 Buick Regal GS and Pontiac Grand Prix GTP model vehicles equipped with L67 3.8L V6 engines and built within these VIN breakpoints: Year Division Model Plant From Through 1997 Buick W Oshawa 2 V1400025 V1482781 1998 Buick W Oshawa 2 W1400008 W1614345 1997 Pontiac W Fairfax VF200090 VF359094 1998 Pontiac W Fairfax WF200104 WF342330 Important: Dealers should confirm vehicle eligibility through GM Access Screen prior to beginning campaign repairs.… Read More

2001 Pontiac Grand Prix Shifter A/T: Service and Repair

Filed Under (Pontiac) by admin on 31-12-2013

Download 2001 Pontiac Grand Prix V6-3.8L VIN K. Shifter A/T: Service and Repair Shift Control Replacement Removal Procedure 1. Remove the horseshoe clip (1) from front of shift control knob, and remove knob. 2. Remove the Console Trim Plate. 3. Remove the console wiring harness. 4. Remove the console shift control wiring harness. 5. Remove the automatic transaxle range selector cable. 6. Remove the park/lock cable. 7. Remove the console shift control nuts. 8. Remove the console shift control. Installation Procedure 1. Install the console shift control. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the console shift control nuts. ^Tighten the console shift control nuts to 24 Nm (18 ft. lbs.) . 3. install the park/lock cable. 4. Install the automatic transaxle range selector cable. 5. Install the console shift control wiring harness. 6. Install the console wiring harness. 7. Install the Console Trim Plate. 8. Adjust the transaxle range selector cable.… Read More

2001-2006 Toyota Sequoia BACK DOOR POWER WINDOW INOPERATIVE

Filed Under (Toyota) by admin on 10-12-2013

Download 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9.… Read More

2001 Mazda Truck MPV DX FRONT DOOR DISASSEMBLY/ASSEMBLY

Filed Under (Mazda) by admin on 31-12-2013

Download 1. Lower or raise the front door glass so that the distance from the top of the front door glass at the rear end to the upper part of the front molding is 185 mm {7.3 in} 2. Disconnect the negative battery cable. 3. Remove the front door trim.4. Disassemble in the order indicated below. 1. Inner handle 2. Front door trim bracket 3. Door screen 4. Front door glass 5. Front manual window regulator 6. Front power window regulator 7. Glass run channel 8. Front door lock 9. Outer handle 10. Door key cylinder 11. Door weatherstrip 12. Door lower weatherstrip 5. Assemble in the reverse order of disassembly. Front Door Glass Disassembly Note 1. Remove the front door glass installation bolts. 2. Slant the front door glass as shown, and remove the front door glass from the inside of the front door. Outer Handle Assembly Note 1. Connect the door key cylinder harness of outer handle as shown.… Read More

2000-UP FORD FOCUS 4 Door Sedan / Wagon, 3 Door Hatchback Audio Installation Instructions

Filed Under (Ford) by admin on 31-12-2013

Download Preliminary: disconnect the negative battery cable. Antenna: the factory antenna is located in the center front of vehicles roof. Radio removal and in-dash installation: note: the factory radio provision is a custom ford double din. When installing an aftermarket din stereo a dash kit is needed. We recommend the scosche fm1375 or fmc1370 installation kit. A set of din removal tools is also needed to remove the factory head unit. We recommend the scosche dt-1 ford din removal tools. 1. Insert ford din removal tools to release clips, pull out stereo, disconnect and remove. Front door speaker installation: note : the factory speaker provision is for a 6 x 8″ speaker. When installing an aftermarket 5 ¼ or 6 ½ speaker, a speaker adapter is required. We recommend the scosche sa68. 1. Extract (7) t-15 torx screws from the perimeter of door panel. 2. Remove screw cover from door opener cup, and extract (1) # 2 philips head screw from behind.… Read More

1997-2003 Honda CRV Signal Mirror Manual Installation Instructions

Filed Under (Honda) by admin on 02-02-2014

Download
Door Panel & Mirror Housing Removal 2002-2003 Honda CRV:1. Open door and lower window. 2. Remove plastic cover from corner of door. 3. Pop-out and remove plastic inserts. 4. Remove door handle plastic cover. 5. Unscrew the (2) screws revealed by the removal of the door handle cover. 6. Pry out door handle as shown. Disengage latch behind door handle and remove door handle. 7. Remove the (2) screws beneath armrest. 8. Lift up and pull door panel out slightly as shown. Disconnect any wiring connection behind door panel. Remove door panel from door. 9. Unscrew the (3) nuts holding the mirror housing to the door. Remove mirror housing from door.
Door Panel & Mirror Housing Removal 1997-2001 Honda CRV : 1. Open door and lower window. 2. Remove screw and plastic grommet on inside corner of door. 3. Remove plastic cover from corner of door. 4. Disconnect the mirror wire harness.… Read More

You might also likeclose