2001 Infiniti QX4 Direct-Hit – Hotline Archive Detail

Download Vehicle Application: 2001 Infiniti QX4 3.5L, USA/Canada 2002 Nissan Pathfinder 3.5L, USA/Canada 2001 Nissan Pathfinder 3.5L, USA/Canada2003 Infiniti QX4 3.5L, USA/Canada Customer Concern: The check engine light is on with a trouble code P1140. Tests/Procedures: 1. Check the right side (passenger side) Intake Valve Timing Control Position (IVTCP) sensor for 12 volts on the Black/White wire. 2. Check the IVTCP sensor for a good ground on the Black wire. 3. Scope the Yellow/Green signal wire and look for a square wave signal of around 8 volts. Check the pattern of the right side sensor and if unsure of the pattern, compare it to the left bank sensor. Potential Causes: IVTCP Sensor Wiring — IVTCP sensor wiring/connection. Tech Tips: This code is for the right (passenger) bank IVTCP Sensor or sensor circuit. The right and left bank sensors can be swapped from side to side to see if the code will follow the sensor.… Read More

2000 Audi A4 Quattro oxygen sensor Bank 1 sensor 1 malfunction

Download 2000 Audi A4 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ, USA/Canada 2000 Audi A6 Quattro 2.8L, Vin H, Eng Cfg V6, Eng Des ATQ Customer Concern: MIL on, DTC P0130 – 16514 – oxygen sensor Bank 1 sensor 1 malfunction; P0150 – 16534 – oxygen sensor Bank 2 sensor 1 malfunction. Engine has extended crank time after sitting for more than a few hours. Tests/Procedures: 1. Trouble Code P0130 (16514) indicates an electrical malfunction with the Bank1, Sensor 1 Oxygen Sensor (O2). Connect a full function Audi compatible scan tool. Enter address menu 01 “Engine Electronics”. Enter functions menu 08 “Read Measuring Value Block”. Enter display group 041. Check specified values in fields 1. Field 1 displays Oxygen Sensor (O2) Bank 1, Sensor 1 (B1S1) heater circuit resistance. Specification is 0.0 to 0.9 Kohm. Note: If the O2′s have not yet reached their operating temperature, there will be no indication in display field 1.… Read More

1999-2001 Infiniti Q45 (FY33) MIL “ON” REAR O2 SENSOR DTC

Download 1999-2001 Q45 (FY33) SERVICE INFORMATION If a 1999, 2000, or 2001 Q45 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) • P0158 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Max. Voltage Monitoring) • P0159 Heated Oxygen Sensor 2 (Rear) (Bank 2) (Response Monitoring) • P0160 Heated Oxygen Sensor 2 (Rear) (Bank 2) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies.… Read More

1999-2003 FORD SUPER DUTY F SERIES HIGH PRESSURE OIL PUMP LEAK

Download FORD: 1998-2003 E SERIES 1999-2003 SUPER DUTY F SERIES 2000-2003 EXCURSION, F-650, F-750 This article supersedes TSB 03-21-50 to update the WARNING service procedure and illustration. DO NOT REMOVE OR ATTEMPT TO REPAIR A LEAK AT THE PLUG PICTURED IN LOWER LEFT ISSUE CORNER OF FIGURE 1, OR DAMAGE TO THE Some 1998-2003 E-Series, 1999-2003 Super Duty, PUMP WILL RESULT. 2000-2003 Excursion, and 2000-2003 F650/750 1998-2003 E-SERIES HIGH PRESSURE OIL vehicles equipped with a 7.3L Diesel engine may PUMP ACCESS PROCEDURE (DISASSEMBLY) exhibit an oil leak at the high pressure oil pump outlet fittings and/or end plug (see Figure 1). The 1. Remove the Intake Air Resonator. For leak may appear to be a rear main crankshaft seal, additional information, refer to Section 303-12 in oil pan gasket, or other engine oil leak due to the the appropriate Workshop Manual. drain hole machined in the crankcase valley which allows any oil in the valley to run down the back of 2.… Read More

2003 Ford Truck Expedition Suspension – Air Suspension Height Sensor Linkage Loose

Download FORD: 2003-2006 Expedition LINCOLN: 2003-2006 Navigator ISSUE Some 2003-2006 Expedition and Navigator vehicles equipped with an air suspension may exhibit an air suspension height sensor linkage arm disengaging from the suspension ball stud or height sensor rotating arm. This concern typically occurs with the rear sensor (Figure 1) but may occur with the front sensors as well. If this occurs, the symptom will typically be the vehicle leaning to one side, the vehicle sitting too low/high, a harsh ride, and/or an inoperative air suspension. In addition, this concern may result in diagnostic trouble code (DTC) C1725 (air suspension front pneumatic failure) or C1726 (air suspension rear pneumatic failure). ACTION When a linkage arm becomes disengaged, do not re-attach the arm and do not replace the sensor unless broken. Instead, install a revised linkage arm on all three (3) sensor assemblies, even if they have not detached from the ball stud.… Read More

1999-2003 Ford F-Series 7.3L PowerStroke Edge Juice Module Installation Instructions

Download
Edge Module and Sensor Wire Installation For trucks with fuse box in a different location, an alternate location for mounting will have to be found. One suggestion is to mount the Juice Module on the side of the air filter box. 1. It is strongly recommended when installing electrical devices that both batteries should be disconnected. Use a 13 mm or 8 mm wrench depending on battery style and remove the negative terminal cable end from each battery. 2. Place the Juice module on top of the fuse box as shown in figure 5. After the installation is complete you will use the supplied Velcro® to secure the Juice module to the fuse box. 3. Connect the MAP “Y” connector between the wire harness and the sensor as shown in Figure 6. This connection is located in front of the passenger side of the vehicle in the engine compartment. 4.… Read More

2003 Chevrolet Tahoe Test Details

Download  2002 Chevrolet Silverado 1500 4.8L, GAS, Vin V, Eng Cfg V8, USA/Canada 2003 Chevrolet Tahoe 4.8L, GAS, Vin V 2003 Chevrolet Silverado 1500 4.8L, GAS, Vin V, Eng Cfg V8 2003 Chevrolet Tahoe 5.3L, FLEX, Vin Z Customer Concern: The engine runs, but lacks power when driving. Has codes P0101 and P0300. Scanner shows misfires all on the same side of the engine. Tests/Procedures: 1. Check the catalytic converter, on the “suspect” bank of the engine, for a restricted (plugged) exhaust system to that side of the engine. 2. Disconnect both front O2 sensors, re-set the fuel trims and see if the problem goes away. 3. If gone with the O2 sensors disconnected, then swap the sensors side to side and see if the problem follows the O2 sensor. Potential Causes: Plugged Exhaust System Oxygen Sensor Diagnostic Codes: P0101, P0300 Author: Christopher Pittman Average Reported Mileage: 92479 Confirmed Fix Summary Confirmed Fix 9 – Catalytic Converter 1 – Exhaust System 1 – Intake Manifold Gasket(s) 1 – Right Catalytic Converter Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Phil Zeuner March 04, 2009 2003 Chevrolet Tahoe, 5.3L, FLEX, Vin Z Replaced Catalytic Converter – Replaced cat.… Read More

Ford CADC Installation Instructions

Download Package Contents: • CADC Module • CADC Harness • CADC Small Parts (if applicable) Ford 7.3L 1994-2003 (International T444e as well) Installation Location: ICP sensor is located on Driver’s side valve cover just to the side of the fuel filter. Install to sensor and factory harness then route harness through firewall. Install harness to module Ford 6.0L 2003 Installation Location: ICP sensor is located behind the turbo. You will need to install this from under the truck. There is a heat shield behind the turbo that needs loosened to expose the ICP sensor. Install to sensor and factory harness then route harness through firewall. Install harness to module Ford 6.0L 2004-2007 Installation Location ICP sensor is located on Passenger- side valve cover very close to the glow plug module. Install to sensor and factory harness then route harness through firewall. Install harness to module Dodge Ram Cummins 5.9L (2003-2007) The rail sensor is on the top of the engine near the intake manifold.… Read More

2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR

Download SELF-DIAGNOSTICS – EEC-V (DIESEL) -2000 Ford Pickup F250 Super Duty EXHAUST BACKPRESSURE (EBP) SENSOR. Perform this test when directed by QUICK TEST. This test is intended to diagnose: Exhaust Backpressure (EBP) Sensor • Wiring Harness Circuits (SIG RTN, VREF & EBP Signal) • Powertrain Control Module (PCM) • 1) DTC P0470 This DTC indicates PCM detected EBP sensor malfunction during KOEO ON-DEMAND SELF-TEST. Possible causes for this DTC are: Faulty EBP Sensor • Open Or Shorted Circuit • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. If EBP reading is less than 18.5 psi, clear DTCs. Repeat KOEO ON-DEMAND SELF-TEST . If DTC is still present, replace PCM. If EBP reading is 18.5 psi or more, go to next step. 2) Check Signal Ground Circuit Turn ignition off. Disconnect EBP sensor connector. Sensor is located on top front of engine.… Read More

2000-2002 Infiniti G20 MIL “ON” REAR O2 SENSOR DTC P0138/P0139/P0140

Download If a 2000 to 2002 G20 has a MIL “On” and any of the following DTCs stored in the ECM: • P0138 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Max. Voltage Monitoring) • P0139 Heated Oxygen Sensor 2 (Rear) (Bank 1) (Response Monitoring) • P0140 Heated Oxygen Sensor 2 (Rear) (Bank 1) (High Voltage) Start with the Service Procedure to find out if the bulletin applies to this vehicle. If it does apply, complete the Service Procedure to repair the incident, if it should occur. SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed).… Read More