1994 Ford Mustang Heating and Defrosting REMOVAL AND INSTALLATION

Download 1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed.… Read More

1991 Infiniti G20 AXLE SHAFTS FRONT

Download 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts. REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose.… Read More

2002 Land Rover Freelander Camshaft Timing Belt Service Repair

Download Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated. Align Front Timing Belt. 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate.… Read More

1989-1990 Acura Legend Radio Replacement

Download 1 : Locate and remove two (2) phillips screws securing the top of the radio dash panel. The 2 screws will be located between the air conditioner vents and the air conditioner controls. STEP 2 : Pull the ashtray out of the dash. Locate and remove two (2) phillips screws hidden underneath the ashtray. STEP 3 : The plastic panel surrounding the gear shift must be removed. This panel simply unsnaps upward from the rest of the center console. With a flat head screwdriver or other flat object, gently pry up the left corner closest to the emergency break. Once this corner is unsnapped, gently pull the panel upward to unsnap the rest of the clips. Remove Factory Radio STEP 4 : Once the plastic panel surrounding the gear shift has been removed, locate and remove two (2) phillips screws securing the lower part of the black plastic dash panel.… Read More

2001 Pontiac Grand Prix Shifter A/T: Service and Repair

Download 2001 Pontiac Grand Prix V6-3.8L VIN K. Shifter A/T: Service and Repair Shift Control Replacement Removal Procedure 1. Remove the horseshoe clip (1) from front of shift control knob, and remove knob. 2. Remove the Console Trim Plate. 3. Remove the console wiring harness. 4. Remove the console shift control wiring harness. 5. Remove the automatic transaxle range selector cable. 6. Remove the park/lock cable. 7. Remove the console shift control nuts. 8. Remove the console shift control. Installation Procedure 1. Install the console shift control. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the console shift control nuts. ^Tighten the console shift control nuts to 24 Nm (18 ft. lbs.) . 3. install the park/lock cable. 4. Install the automatic transaxle range selector cable. 5. Install the console shift control wiring harness. 6. Install the console wiring harness. 7. Install the Console Trim Plate. 8. Adjust the transaxle range selector cable.… Read More

Honda S2000 Installation Instructions

Download
HARDWARE KIT: • 2 – front foot plates (1 left / 1 right) • 2 – rear foot plates • 12 – 3/8″ X 1-1/4″ bolts • 6 – 3/8″ self locking nuts 18 – 3/8″ SAE flat washers TOOLS NEEDED: • wrenches • 2 – 9/16″ • 10mm • 12mm • 14mm • #2 phillips head screwdriver • Floor jack and jack stands • hack saw or aviation snips for cutting sheet metal and plastic interior panels belt sander or half round file for fitting plastic interior panels 1. Remove the seats. Slide the seat belt out of the loop. Unclip the seat belt warning sensor. 2. Remove the laundry hooks on the rear trim panel. Pop out the rear trim panel. 3. Remove the door sill trim. Pull up carefully. 4. Remove the nut under the shifter knob (left hand thread?) and remove the shifter knob. 5. Pop the center console up after pulling up the e-brake handle.… Read More

1997-2002 CHEVY S-10 BLAZER KIT #152 INSTALLATION INSTRUCTIONS

Download 1. Read all warnings and instructions completely and carefully before you begin. 2. Check to make sure the kit is complete (refer to the Parts List, section E). 3. Only install this kit on the vehicle for which it is intended. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-0979. 4. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. 5. Disconnect both battery cables. Disconnect the negative cable (1) first, then the positive cable (2) from the battery (3). 6. Remove cover (4) and airbag “SIR” fuse (5) from fuse panel (6).Get ready to install the kit. 1. Remove the grille. a. Remove ten pull clips (7) and grille (8) from core support (9). b. Remove two turn signal lamps (10) from turn signal housings (11).… Read More

2002 Acura RSX-Type S Short Throw Shift Adapter Installation Manual

Download 1. Pull down chrome collar and carefully unscrew and remove the stock shift knob. 2. Remove the front console cover. Pull up from the front to unclip the clips and remove from the vehicle. 3. Remove the 2 screws securing the front part of the console. Remove any additional screws that may be holding the center part of the console in place, this may vary by year and model. Lift the 2 tabs shown to the right over the center section of the console so that they rest on the outside of the console assembly. 4. Spread the front sections of the console away from the center console to unclip the 2 clips securing them in place. This may be simplified by pushing from the inside with a hard object next to the clip. 5. Pull the center console to the rear of the vehicle ensuring the sides of the front section of the console remain apart and out of the way.… Read More

2006 Honda Civic SI Comptech Supercharger Kit Installation Instructions

Download STEP #1 Evacuate A/C system: • Have your local Air conditioning shop remove the HFC-134a refrigerant from your A/C system. They can reuse your coolant. After the supercharger installation you will need to return the car to them and have them refill and charge the system. This service should cost approximately $80.00. STEP #2 Remove ECM and ship to Hondata: • Remove the battery. • Remove ECM cover (A). • Remove bolts (D), then lift up the ECM. • Disconnect the ECM connectors A, B, and C. • Remove ECM and ship to Hondata (see Address to right.) STEP #3 Drain Coolant: • Jack up and support the front of the car on jack stands. • Make sure the engine is cool and remove the radiator cap. • Drain the cooling system by loosening the drain plug (A) at the bottom of the radiator. • Once all of the coolant is drained close the drain plug.… Read More

1988 Jeep Cherokee Clutch Hydraulic Installation Guide

Download
REMOVAL & INSTALLATION TRANSMISSION Removal 1) Remove the shift knob and lock nut from transmission and transfer case shift levers (if equipped). On Wrangler models, remove screws attaching transmission and transfer case shift lever boots and remove both boots. 2) On all other models, raise outer gearshift lever boot and remove upper part on center console. Remove lower part of console, remove inner boot and gearshift lever. 3) On Wrangler models, remove transmission shift tower dust cover. Remove transmission shift lever and stub shaft. DO NOT remove shift lever from stub shaft. 4) On all models, raise and support vehicle. Drain transmission lubricant. Mark rear drive shaft for reassembly and remove rear drive shaft. Support transmission assembly and remove crossmember. Disconnect speedometer cable and wiring from back-up light switch. 5) On 4WD models, drain transfer case lubricant. Disconnect transfer case vacuum hoses and linkage. Tag vacuum hoses for reassembly. Disconnect front drive shaft and secure out of way.… Read More